参数资料
| 型号： | ADP3301ARZ-3.2 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 6/8页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 3.2V .1A 8SOIC |
| 标准包装： | 98 |
| 系列： | anyCAP® |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 3.2V |
| 输入电压： | 最高 12V |
| 电压 - 压降（标准）： | 0.1V @ 100mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 100mA |
| 工作温度： | -20°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
ADP3301
APPLICATION INFORMATION
anyCAP?*
The ADP3301 is very easy to use. The only external component
required for stability is a small 0.47 μ F bypass capacitor on the
output. Unlike the conventional LDO designs, the ADP3301 is
stable with virtually any type of capacitors (anyCAP?*) indepen-
dent of the capacitor’s ESR (Effective Series Resistance) value.
In a typical application, if the shutdown feature is not used, the
shutdown pin (Pin 5) should be tied to the input pin. Pins 7
and 8 must be tied together, as well as Pins 1 and 2, for proper
operation.
Capacitor Selection
Output Capacitors: as with any micropower device, output
transient response is a function of the output capacitance. The
ADP3301 is stable with a wide range of capacitor values, types
and ESR (anyCAP?*). A capacitor as low as 0.47 μ F is all that
is needed for stability. However, larger capacitors can be used if
high output current surges are anticipated. The ADP3301 is
stable with extremely low ESR capacitors (ESR ≈ 0), such as
multilayer ceramic capacitors (MLCC) or OSCON.
Input Bypass Capacitor: an input bypass capacitor is not
required; however, for applications where the input source is
high impedance or far from the input pins, a bypass capacitor is
recommended. Connecting a 0.47 μ F capacitor from the input
pins (Pins 7 and 8) to ground reduces the circuit’s sensitivity to
PC board layout. If a bigger output capacitor is used, the input
capacitor should be 1 μ F minimum.
Low ESR capacitors offer better performance on a noisy supply;
however, for less demanding requirements a standard tantalum
or aluminum electrolythic capacitor is adequate.
Noise Reduction
A noise reduction capacitor (C NR ) can be used to further reduce
the noise by 6 dB–10 dB (Figure 20). Low leakage capacitors in
the 10 nF–100 nF range provide the best performance. Since
the noise reduction pin (NR) is internally connected to a high
impedance node, any connection to this node should be carefully
done to avoid noise pickup from external sources. The pad
connected to this pin should be as small as possible. Long PC
board traces are not recommended.
NR 3
Thermal Overload Protection
The ADP3301 is protected against damage due to excessive
power dissipation by its thermal overload protection circuit,
which limits the die temperature to a maximum of 165 ° C.
Under extreme conditions (i.e., high ambient temperature and
high power dissipation) where die temperature starts to rise
above 165 ° C, the output current is reduced until die tempera-
ture has dropped to a safe level. Output current is restored when
the die temperature is reduced.
Current and thermal limit protections are intended to protect
the device against accidental overload conditions. For normal
operation, device power dissipation should be externally limited
so that junction temperatures will not exceed 125 ° C.
Calculating Junction Temperature
Device power dissipation is calculated as follows :
PD = (V IN – V OUT ) I LOAD + (V IN ) I GND
Where I LOAD and I GND are load current and ground current, V IN
and V OUT are input and output voltages respectively.
Assuming I LOAD = 100 mA, I GND = 2 mA, V IN = 9 V and
V OUT = 5.0 V, device power dissipation is:
PD = (9 V – 5 V ) 100 mA + (9 V ) 2 mA = 418 mW
The proprietary package used in ADP3301 has a thermal
resistance of 96 ° C/W, significantly lower than a standard
8-pin SOIC package at 170 ° C/W.
Junction temperature above ambient temperature will be
approximately equal to :
0.418 W × 96 ° C/W = 40.1 ° C
To limit the maximum junction temperature to 125 ° C, maxi-
mum ambient temperature must be lower than:
T A(MAX) = 125 ° C – 40.1 ° C = 84.9 ° C
Printed Circuit Board Layout Consideration
All surface mount packages rely on the traces of the PC board to
conduct heat away from the package.
In standard packages the dominant component of the heat
resistance path is the plastic between the die attach pad and the
individual leads. In typical thermally enhanced packages, one or
more of the leads are fused to the die attach pad, significantly
V IN
C1 +
1μF
7
8
ADP3301-5.0
IN OUT
ERR
5 4
ON
OFF
1
2
6
C NR
10nF
R1
330k ?
E OUT
+
V OUT = 5V
C2
10μF
decreasing this component. However, to make the improvement
meaningful, a significant copper area on the PCB has to be
attached to these fused pins.
The ADP3301’s patented thermal coastline lead frame design
uniformly minimizes the value of the dominant portion of the
thermal resistance. It ensures that heat is conducted away by all
pins of the package. This yields a very low 96 ° C/W thermal
SD
GND
resistance for an SO-8 package, without any special board
layout requirements, relying on the normal traces connected to
Figure 20. Noise Reduction Circuit
–6 –
the leads. The thermal resistance can be decreased by approxi-
mately an additional 10% by attaching a few square cm of
copper area to the V IN pin of the ADP3301 package.
REV. A
相关PDF资料 |
PDF描述 |
|---|---|
| AMC13DRXN-S734 | CONN EDGECARD 26POS DIP .100 SLD |
| RYM36DTBN | CONN EDGECARD 72POS R/A .156 SLD |
| LT1117CST-5 | IC REG LDO 5V .8A SOT-223 |
| AMC13DRXH-S734 | CONN EDGECARD 26POS DIP .100 SLD |
| RYM36DTBH | CONN EDGECARD 72POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP3301ARZ-3-REEL | 功能描述:IC REG LDO 3V .1A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:anyCAP® 标准包装:1 系列:anyCAP® 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:最高 6V 电压 - 压降（标准）:0.23V @ 1.5A 稳压器数量:1 电流 - 输出:1.5A 电流 - 限制（最小）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:TO-261-4，TO-261AA 供应商设备封装:SOT-223-3 包装:Digi-Reel® 其它名称:ADP3339AKCZ-3.3-RLDKR |
| ADP3301ARZ-5 | 功能描述:IC REG LDO 5V .1A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:anyCAP® 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3V 输入电压:最高 5.5V 电压 - 压降（标准）:0.12V @ 150mA 稳压器数量:1 电流 - 输出:150mA（最小值） 电流 - 限制（最小）:220mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 供应商设备封装:TSOT-23-5 包装:带卷 (TR) 其它名称:ADP160AUJZ-3.0-R7TR |
| ADP3301ARZ-5 | 制造商:Analog Devices 功能描述:IC LINEAR REGULATOR 5.0V |
| ADP3301ARZ-5-REEL | 功能描述:IC REG LDO 5V .1A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:anyCAP® 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:2.5 V ~ 5.5 V 电压 - 压降（标准）:0.1V @ 200mA 稳压器数量:2 电流 - 输出:300mA 电流 - 限制（最小）:350mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-UFQFN 供应商设备封装:8-MLPQ-UT（1.5x1.5） 包装:剪切带 (CT) 产品目录页面:1358 (CN2011-ZH PDF) 其它名称:SC560HULCT |
| ADP3302 | 制造商:AD 制造商全称:Analog Devices 功能描述:High Accuracy anyCAP⑩ Adjustable 200 mA Low Dropout Linear Regulator |
发布紧急采购，3分钟左右您将得到回复。