- 您现在的位置：买卖IC网 > PDF目录4767 > ADP3330ARTZ-2.75RL (Analog Devices Inc)IC REG LDO 2.75V .2A SOT23-6 PDF资料下载
参数资料
| 型号： | ADP3330ARTZ-2.75RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 9/12页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 2.75V .2A SOT23-6 |
| 设计资源： | Half-Duplex, Isolated RS-485 Interface (CN0031) |
| 标准包装： | 1 |
| 系列： | anyCAP® |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 2.75V |
| 输入电压： | 2.9 V ~ 12 V |
| 电压 - 压降（标准）： | 0.14V @ 200mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 200mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 |
| 供应商设备封装： | SOT-23-6 |
| 包装： | 标准包装 |
| 其它名称： | ADP3330ARTZ-2.75RLDKR |
ADP3330
Printed Circuit Board Layout Considerations
All surface mount packages rely on the traces of the PC board
to conduct heat away from the package.
In standard packages the dominant component of the heat
resistance path is the plastic between the die attach pad and the
individual leads. In typical thermally enhanced packages one or
more of the leads are fused to the die attach pad, significantly
decreasing this component. To make the improvement mean-
ingful, however, a significant copper area on the PCB must be
attached to these fused pins.
The patented chip-on-lead frame design of the ADP3330
uniformly minimizes the value of the dominant portion of the
thermal resistance. It ensures that heat is conducted away by all
pins of the package. This yields a very low 165 ° C/W thermal
resistance for an SOT-23-6 package, without any special board
layout requirements, just relying on the normal traces con-
nected to the leads. This yields a 17% improvement in heat
dissipation capability as compared to a standard SOT-23-6
package. The thermal resistance can be decreased by, approxi-
mately, an additional 10% by attaching a few square cm of
Low Power, Low Dropout Applications
ADP3330 is well suited for applications such as cellular phone
handsets that require low quiescent current and low dropout
voltage features. ADP3330 draws 34 μ A typical under light load
situations (i.e., load current = 100 μ A), which results in low
power consumption when the cell phone is in standby mode.
Figure 23 shows an application in which the ADP3330 is used
in a handset to provide 2.75 V nominal output voltage. The cell
phone is powered from 3 cell NiCd or 1 cell Li-Ion battery.
ADP3330 guarantees an accuracy of 1.4%, even when the input/
output differential is merely 250 mV (worst case). This implies
that the output is regulated and within specification even when
the battery voltage has reached its end-of-discharge voltage of
3 V. The output voltage never falls below 2.7 V, even under
worst case load and temperature conditions. The low dropout
feature coupled with the high accuracy of the ADP3330 ensures
that the system is reliably powered until the end of the life of the
battery, which results in increased system talk time.
END OF DISCHARGE VOLTAGE
OF 3 CELL NiCd OR 1 CELL
copper area to the V IN pin of the ADP3303 package.
MINIMUM BATTERY
Li-Ion BATTERY
It is not recommended to use solder mask or silkscreen on the
PCB traces adjacent to the ADP3330’s pins since it will increase
the junction to ambient thermal resistance of the package.
Error Flag Dropout Detector
VOLTAGE 3.0V
NOMINAL OUTPUT
250mV MAXIMUM INPUT-OUTPUT
OVERHEAD FOR 200mA OUTPUT
CURRENT
The ADP3330 will maintain its output voltage over a wide
range of load, input voltage and temperature conditions. If the
VOLTAGE 2.75V
–1.4% OUTPUT
VOLTAGE ACCURACY
output is about to lose regulation by reducing the supply voltage
below the combined regulated output and dropout voltages,
2.712V
12mV TRANSIENT, LINE AND
the ERR flag will be activated. The ERR output is an open
ABSOLUTE MINIMUM
LOAD RESPECTIVE MARGIN
collector, which will be driven low.
Once set, the ERR flag’s hysteresis will keep the output low
until a small margin of operating range is restored either by
raising the supply voltage or reducing the load.
Shutdown Mode
Applying a TTL high signal to the shutdown ( SD ) pin, or tying
it to the input pin, will turn the output ON. Pulling SD down to
0.4 V or below, or tying it to ground, will turn the output OFF.
In shutdown mode, quiescent current is reduced to much less
than 1 μ A.
REV. A
–9 –
OUTPUT VOLTAGE
2.700V
Figure 23. LDO Budgeting for a 3 Cell NiCd/1 Cell
Li-Ion Supply
相关PDF资料 |
PDF描述 |
|---|---|
| ASM15DRMT | CONN EDGECARD 30POS .156 WW |
| AGM15DRMT | CONN EDGECARD 30POS .156 WW |
| SPX3940T-L-5-0/TR | IC REG LDO 5V 1A TO263-3 |
| HMC19DRTI-S93 | CONN EDGECARD 38POS DIP .100 SLD |
| AP130-25WL-7 | IC REG LDO 2.5V .3A SC59-3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP3330ARTZ3.3 | 制造商:Analog Devices 功能描述:LDO 2.9-12V 0.14VD 0.2A 3. 制造商:Analog Devices 功能描述:LDO, 2.9-12V, 0.14VD, 0.2A, 3.3V, 6SOT23; Primary Input Voltage:12V; Output Voltage Fixed:3.3V; Dropout Voltage Vdo:140mV; Voltage Regulator Case Style:SOT-23; No. of Pins:6; Output Current:200mA; Operating Temperature Min:-40C; ;RoHS Compliant: Yes |
| ADP3330ARTZ3.3-RL7 | 功能描述:IC REG LDO 3.3V .2A SOT23-6 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:anyCAP® 标准包装:75 系列:- 稳压器拓扑结构:正，可调式 输出电压:1.2 V ~ 37 V 输入电压:4.2 V ~ 40 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:500mA 电流 - 限制（最小）:500mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-252-3，DPak（2 引线+接片），SC-63 供应商设备封装:TO-252-3 包装:管件 产品目录页面:1286 (CN2011-ZH PDF) 其它名称:*LM317AMDT/NOPBLM317AMDT |
| ADP3330ARTZ-3.6-R7 | 功能描述:IC REG LDO 3.6V .2A SOT23-6 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:anyCAP® 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.7V 输入电压:最高 5.5V 电压 - 压降（标准）:0.21V @ 150mA 稳压器数量:1 电流 - 输出:150mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 供应商设备封装:TSOT-23-5 包装:剪切带 (CT) 产品目录页面:1100 (CN2011-ZH PDF) 其它名称:576-1852-1 |
| ADP3330ARTZ-3-RL7 | 功能描述:IC REG LDO 3V .2A SOT23-6 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:anyCAP® 标准包装:75 系列:- 稳压器拓扑结构:正，可调式 输出电压:1.2 V ~ 37 V 输入电压:4.2 V ~ 40 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:500mA 电流 - 限制（最小）:500mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-252-3，DPak（2 引线+接片），SC-63 供应商设备封装:TO-252-3 包装:管件 产品目录页面:1286 (CN2011-ZH PDF) 其它名称:*LM317AMDT/NOPBLM317AMDT |
| ADP3330ARTZ-5 | 制造商:Analog Devices 功能描述:LDO 2.9-12V 0.14VD 0.2A 5V 制造商:Analog Devices 功能描述:LDO, 2.9-12V, 0.14VD, 0.2A, 5V, 6SOT23; Primary Input Voltage:12V; Output Voltage Fixed:5V; Dropout Voltage Vdo:140mV; Voltage Regulator Case Style:SOT-23; No. of Pins:6; Output Current:200mA; Operating Temperature Min:-40C; ;RoHS Compliant: Yes |
发布紧急采购，3分钟左右您将得到回复。