参数资料
| 型号： | ADP3338AKC-3-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/16页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 3V 1A SOT223 |
| 标准包装： | 1 |
| 系列： | anyCAP® |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 3V |
| 输入电压： | 最高 8V |
| 电压 - 压降（标准）： | 0.19V @ 1A |
| 稳压器数量： | 1 |
| 电流 - 输出： | 1A |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-261-4，TO-261AA |
| 供应商设备封装： | SOT-223-3 |
| 包装： | 标准包装 |
| 其它名称： | ADP3338AKC-3-RLDKR |
ADP3338
APPLICATION INFORMATION
CAPACITOR SELECTION
Output Capacitor
The stability and transient response of the LDO is a function of
the output capacitor. The ADP3338 is stable with a wide range
of capacitor values, types, and ESR (anyCAP). A capacitor as
low as 1 μF is the only requirement for stability. A higher ca-
pacitance may be necessary if high output current surges are
anticipated, or if the output capacitor cannot be located near the
output and ground pins. The ADP3338 is stable with extremely
low ESR capacitors (ESR ≈ 0) such as multilayer ceramic capacitors
(MLCC) or OSCON. Note that the effective capacitance of some
capacitor types falls below the minimum over temperature or
with dc voltage.
Input Capacitor
CALCULATING POWER DISSIPATION
Device power dissipation is calculated as
P D = ( V IN – V OUT ) × I LOAD + ( V IN × I GND )
Where I LOAD and I GND are load current and ground current, and
V IN and V OUT are the input and output voltages, respectively.
Assuming the worst-case operating conditions are I LOAD = 1.0 A,
I GND = 10 mA, V IN = 3.3 V, and V OUT = 2.5 V, the device power
dissipation is
P D = (3.3 V – 2.5 V) × 1000 mA + (3.3 V × 10 mA) = 833 mW
So, for a junction temperature of 125°C and a maximum
ambient temperature of 85°C, the required thermal resistance
from junction to ambient is
An input bypass capacitor is not strictly required, but is recom-
mended in any application involving long input wires or high
source impedance. Connecting a 1 μF capacitor from the input
θ JA =
125 ° C ? 85 ° C
0 . 833 W
= 48 ° C/W
to ground reduces the sensitivity of the circuit to PC board
layout and input transients. If a larger output capacitor is
necessary, a larger value input capacitor is recommended.
OUTPUT CURRENT LIMIT
The ADP3338 is short-circuit protected by limiting the pass
transistor’s base drive current. The maximum output current is
THERMAL OVERLOAD PROTECTION
The ADP3338 is protected against damage due to excessive
power dissipation by its thermal overload protection circuit.
Thermal protection limits the die temperature to a maximum of
160°C. Under extreme conditions, such as high ambient
temperature and power dissipation where the die temperature
starts to rise above 160°C, the output current is reduced until
the die temperature has dropped to a safe level.
Current and thermal limit protections are intended to protect
the device against accidental overload conditions. For normal
operation, externally limit the power dissipation of the device
so the junction temperature does not exceed 150°C.
PRINTED CIRCUIT BOARD LAYOUT
CONSIDERATIONS
The thermal resistance, θ JA , of the SOT-223 is determined by the
sum of the junction-to-case and the case-to-ambient thermal
resistances. The junction-to-case thermal resistance, θ JC , is
determined by the package design and is specified at 26.8°C/W.
However, the case-to-ambient thermal resistance is determined
by the printed circuit board design.
As shown in Figure 22, the amount of copper to which the
ADP3338 is mounted affects thermal performance. When
mounted to the minimal pads of 2 oz. copper, as shown in
under the ADP3338, as shown in Figure 22 (b), reduces the θ JA to
102.9°C/W. Increasing the copper pad to one square inch, as
shown in Figure 22 (c), reduces the θ JA even further to 52.8°C/W.
a
b
c
Figure 22. PCB Layouts
Rev. B | Page 10 of 16
相关PDF资料 |
PDF描述 |
|---|---|
| HSM22DRYN-S13 | CONN EDGECARD 44POS .156 EXTEND |
| NCP4682DMU25TCG | IC REG LDO 2.5V .15A UDFN4 |
| LT1121IN8-3.3 | IC REG LDO 3.3V .15A 8-DIP |
| LT1121IN8#PBF | IC REG LDO ADJ .15A 8-DIP |
| HMM22DRYN-S13 | CONN EDGECARD 44POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP3338AKC-3-RL7 | 制造商:Analog Devices 功能描述:LDO Regulator Pos 3V 1.6A 4-Pin(3+Tab) SOT-223 T/R |
| ADP3338AKC-5 | 制造商:AD 制造商全称:Analog Devices 功能描述:High-Accuracy Ultralow IQ, 1 A, anyCAP Low Dropout Regulator |
| ADP3338AKC-5-REEL | 制造商:AD 制造商全称:Analog Devices 功能描述:High Accuracy, Ultralow IQ, 1A, anyCAP Low Dropout Regulator |
| ADP3338AKC-5-REEL7 | 功能描述:IC REG LDO 5V 1A SOT-223 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:anyCAP® 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式和可调式 输出电压:3.3V，1.25 V ~ 5.7 V 输入电压:4.5 V ~ 7 V 电压 - 压降（标准）:1.1V @ 1A 稳压器数量:2 电流 - 输出:1A 电流 - 限制（最小）:1A 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-252-5，DPak（4 引线 + 接片），TO-252AD 供应商设备封装:PPAK 包装:管件 其它名称:497-3576-5 |
| ADP3338AKCZ-1.5-R7 | 功能描述:IC REG LDO 1.5V 1A SOT-223 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:anyCAP® 产品培训模块:MIC5365/66 Ultra-small LDO Regulators 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:3V 输入电压:最高 5.5V 电压 - 压降（标准）:0.155V @ 150mA 稳压器数量:1 电流 - 输出:150mA 电流 - 限制（最小）:200mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:4-UDFN 裸露焊盘，4-TMLF? 供应商设备封装:4-TMLF?（1x1） 包装:Digi-Reel® 其它名称:576-3192-6 |
发布紧急采购，3分钟左右您将得到回复。