参数资料
| 型号： | ADP7102ARDZ-1.5-R7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 21/28页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 1.5V .3A 8SOIC |
| 标准包装： | 1,000 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 1.5V |
| 输入电压： | 3.3 V ~ 20 V |
| 稳压器数量： | 1 |
| 电流 - 输出： | 300mA（最小值） |
| 电流 - 限制（最小）： | 450mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm Width）裸露焊盘 |
| 供应商设备封装： | 8-SOIC-EP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页
Data Sheet
CURRENT LIMIT AND THERMAL OVERLOAD
PROTECTION
The ADP7102 is protected against damage due to excessive
power dissipation by current and thermal overload protection
circuits. The ADP7102 is designed to current limit when the
output load reaches 400 mA (typical). When the output load
exceeds 400 mA, the output voltage is reduced to maintain a
constant current limit.
Thermal overload protection is included, which limits the
junction temperature to a maximum of 150°C (typical). Under
extreme conditions (that is, high ambient temperature and/or
high power dissipation) when the junction temperature starts to
rise above 150°C, the output is turned off, reducing the output
current to zero. When the junction temperature drops below
ADP7102
To guarantee reliable operation, the junction temperature
of the ADP7102 must not exceed 125°C. To ensure that the
junction temperature stays below this maximum value, the
user must be aware of the parameters that contribute to
junction temperature changes. These parameters include
ambient temperature, power dissipation in the power device,
and thermal resistances between the junction and ambient air
(θ JA ). The θ JA number is dependent on the package assembly
compounds that are used and the amount of copper used to
solder the package GND pins to the PCB.
LFCSP packages for various PCB copper sizes. Table 7 shows
the typical Ψ JB values of the 8-lead SOIC and 8-lead LFCSP.
Table 6. Typical θ JA Values
135°C, the output is turned on again, and output current is
restored to its operating value.
Consider the case where a hard short from VOUT to ground
occurs. At first, the ADP7102 current limits, so that only 400 mA
is conducted into the short. If self heating of the junction is
great enough to cause its temperature to rise above 150°C,
thermal shutdown activates, turning off the output and
Copper Size (mm 2 )
25 1
100
500
1000
6400
LFCSP
165.1
125.8
68.1
56.4
42.1
θ JA (°C/W)
SOIC
167.8
111
65.9
56.1
45.8
Device soldered to minimum size pin traces.
reducing the output current to zero. As the junction
temperature cools and drops below 135°C, the output turns on
and conducts 400 mA into the short, again causing the junction
temperature to rise above 150°C. This thermal oscillation
1
Table 7. Typical Ψ JB Values
Model Ψ JB (°C/W)
between 135°C and 150°C causes a current oscillation between
LFCSP
15.1
400 mA and 0 mA that continues as long as the short remains at
the output.
Current and thermal limit protections are intended to protect
the device against accidental overload conditions. For reliable
operation, device power dissipation must be externally limited
so the junction temperature does not exceed 125°C.
THERMAL CONSIDERATIONS
In applications with low input-to-output voltage differential,
the ADP7102 does not dissipate much heat. However, in
applications with high ambient temperature and/or high
input voltage, the heat dissipated in the package may become
large enough that it causes the junction temperature of the
die to exceed the maximum junction temperature of 125°C.
When the junction temperature exceeds 150°C, the converter
enters thermal shutdown. It recovers only after the junction
temperature has decreased below 135°C to prevent any permanent
damage. Therefore, thermal analysis for the chosen application
SOIC 31.3
The junction temperature of the ADP7102 is calculated from
the following equation:
T J = T A + ( P D × θ JA )
where:
T A is the ambient temperature.
P D is the power dissipation in the die, given by
P D = [( V IN ? V OUT ) × I LOAD ] + ( V IN × I GND )
where:
I LOAD is the load current.
I GND is the ground current.
V IN and V OUT are input and output voltages, respectively.
Power dissipation due to ground current is quite small and
can be ignored. Therefore, the junction temperature equation
simplifies to the following:
T J = T A + {[( V IN ? V OUT ) × I LOAD ] × θ JA }
(2)
(3)
(4)
is very important to guarantee reliable performance over all
conditions. The junction temperature of the die is the sum of
the ambient temperature of the environment and the tempera-
ture rise of the package due to the power dissipation, as shown
in Equation 2.
As shown in Equation 4, for a given ambient temperature,
input-to-output voltage differential, and continuous load
current, there exists a minimum copper size requirement for
the PCB to ensure that the junction temperature does not rise
above 125°C. Figure 71 to Figure 78 show junction temperature
calculations for different ambient temperatures, power dissipa-
tion, and areas of PCB copper.
Rev. C | Page 21 of 28
相关PDF资料 |
PDF描述 |
|---|---|
| LT3082IDD#PBF | IC REG LDO ADJ .2A 8DFN |
| MIC29201-5.0WU TR | IC REG LDO 5V .4A TO-263-5 |
| MIC29201-4.8WU TR | IC REG LDO 4.85V .4A TO-263-5 |
| MIC5367-3.3YMT TR | IC REG LDO 3.3V .15A 6-TMLF |
| RMM22DTBN-S664 | CONN EDGECARD 44POS R/A .156 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP7102ARDZ-2.5-R7 | 功能描述:IC REG LDO 2.5V .3A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 产品培训模块:More Information on LDOs 标准包装:50 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:最高 15V 电压 - 压降（标准）:1.1V @ 800mA 稳压器数量:1 电流 - 输出:800mA 电流 - 限制（最小）:800mA 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-4，D²Pak（3 引线+接片），TO-263AA 供应商设备封装:D2PAK-3 包装:管件 |
| ADP7102ARDZ-3.0-R7 | 功能描述:IC REG LDO 3V .3A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 产品培训模块:More Information on LDOs 标准包装:50 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:最高 15V 电压 - 压降（标准）:1.1V @ 800mA 稳压器数量:1 电流 - 输出:800mA 电流 - 限制（最小）:800mA 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-4，D²Pak（3 引线+接片），TO-263AA 供应商设备封装:D2PAK-3 包装:管件 |
| ADP7102ARDZ-3.3-R7 | 功能描述:IC REG LDO 3.3V .3A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 产品培训模块:More Information on LDOs 标准包装:50 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:最高 15V 电压 - 压降（标准）:1.1V @ 800mA 稳压器数量:1 电流 - 输出:800mA 电流 - 限制（最小）:800mA 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-4，D²Pak（3 引线+接片），TO-263AA 供应商设备封装:D2PAK-3 包装:管件 |
| ADP7102ARDZ-5.0-R7 | 功能描述:IC REG LDO 5V .3A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 产品培训模块:More Information on LDOs 标准包装:50 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:最高 15V 电压 - 压降（标准）:1.1V @ 800mA 稳压器数量:1 电流 - 输出:800mA 电流 - 限制（最小）:800mA 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-4，D²Pak（3 引线+接片），TO-263AA 供应商设备封装:D2PAK-3 包装:管件 |
| ADP7102ARDZ-9.0-R7 | 功能描述:IC REG LDO 9V .3A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 产品培训模块:More Information on LDOs 标准包装:50 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:最高 15V 电压 - 压降（标准）:1.1V @ 800mA 稳压器数量:1 电流 - 输出:800mA 电流 - 限制（最小）:800mA 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-4，D²Pak（3 引线+接片），TO-263AA 供应商设备封装:D2PAK-3 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。