参数资料
| 型号： | ADR827ARMZ-R2 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/20页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP GP R-R 1MHZ LP 10MSOP |
| 产品变化通告： | Product Discontinuance 27/Oct/2011 |
| 标准包装： | 250 |
| 放大器类型： | 通用 |
| 电路数： | 1 |
| 输出类型： | 满摆幅 |
| 转换速率： | 0.5 V/µs |
| 增益带宽积： | 1MHz |
| 电流 - 输入偏压： | 10nA |
| 电压 - 输入偏移： | 100µV |
| 电流 - 电源： | 400µA |
| 电流 - 输出 / 通道： | 20mA |
| 电压 - 电源，单路/双路(±)： | 2.7 V ~ 15 V，±2.7 V ~ 15 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 带卷 (TR) |
ADR821/ADR827
Rev. 0 | Page 18 of 20
APPLICATIONS INFORMATION
+2.5 V AND 2.5 V OUTPUTS (ADR821)
0
66
65
-0
03
REF
REF_OUT
AMP_OUT
V–
V+
10k
R1
R2
+2.5V
–2.5V
+IN
0.1F
Figure 38. +2.5 V and 2.5 V Outputs
In many dual-supply applications, it is desirable to have ±2.5 V
references. Using the configuration shown in Figure 38, it is
possible to generate 2.5 V with the help of a +2.5 V reference,
an internal op amp, and 10 kΩ resistors. The supply voltages V+
and V should be greater than +2.8 V and 2.8 V, respectively.
The op amp is configured as an inverting amplifier with a gain
of 1, which produces 2.5 V at the output of the op amp. The
output of the reference is fed to the amplifier inverting input.
Because the op amp has very low input offset voltage (500 μV
over the full temperature range) and the TC ratio of the
resistors is typically ±25 ppm/°C, the 2.5 V output is less than
7 mV away from the theoretical value.
2.5 V AND 5.0 V OUTPUTS (ADR821)
06
66
5-
00
4
REF_OUT
AMP_OUT
V–
V+
10k
R1
R2
2.5V
5.0V
+IN
–IN
0.1F
REF
Figure 39. 2.5 V and 5.0 V Outputs
In many single-supply applications, it is desirable to have
multiple reference voltages. Using the configuration shown in
Figure 39, it is possible to generate 5.0 V with the help of a
2.5 V reference, an internal op amp, and resistors. V+ should
be kept at greater than 5.8 V and V can be connected either
to ground or to negative supply. The output of the reference is
fed to the amplifier noninverting input. The op amp is config-
ured as a noninverting amplifier with a gain of +2, which
produces 5 V at the output of the op amp. Using the guaranteed
maximum offset voltage over the temperature, and the typical
TC ratio of the resistors over the full temperature range, the
output is within 15 mV of the calculated value.
MULTIPLE 2.5 V OUTPUTS (ADR821)
06
66
5-
04
0
REF_OUT
AMP_OUT
V–
V+
10k
R1
R2
2.5V
+IN
–IN
0.1F
REF
Figure 40. Multiple 2.5 V Outputs
On some boards, sensitive analog circuits, such as a VCO, exist
with noisy digital circuits. If the supply current requirements
are low (less than 3 mA), series references and op amps can be
used. Using the configuration shown in Figure 40, two different
2.5 V supplies can be created using a single ADR821. The supply
voltage V+ should be greater than 2.8 V and V can be con-
nected to ground or a negative voltage. The op amp is configured
as a voltage follower with a gain of +1, which produces 2.5 V at
the output of the op amp. The output of the reference is fed
to the amplifier noninverting input. Because the op amp has
very low input offset voltage (500 μV maximum over the full
temperature range), the output voltage from the op amp section
tracks the reference voltage within 1 mV. For a dynamic load,
such as the reference input pin on some analog-to-digital
converters, the load should be connected to an op amp output
and the noise sensitive circuitry, such as a VCO, should be
connected to the reference output. If the dynamic load is con-
nected to the reference voltage, any perturbations appear as a
signal to the input of the voltage follower and appear on the
other output.
相关PDF资料 |
PDF描述 |
|---|---|
| 6-534998-5 | CONN RECEPT 30POS .100 VERT DUAL |
| WSLT2512R2000FEA | RES .2 OHM 1W 1% 2512 SMD |
| 5-534206-7 | CONN RECEPT 14POS .100 VERT DUAL |
| MMA25-0141R1 | CONN RACK/PANEL 14POS 5A |
| 350833-4 | CONN HEADER 4POS VERT .250 GOLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADR827ARMZ-R21 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Power, Precision Reference and Op Amp |
| ADR827ARMZ-REEL7 | 功能描述:IC OPAMP GP R-R 1MHZ LP 10MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:0.11 V/µs 增益带宽积:350kHz -3db带宽:- 电流 - 输入偏压:4nA 电压 - 输入偏移:20µV 电流 - 电源:260µA 电流 - 输出 / 通道:20mA 电压 - 电源，单路/双路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SO 包装:带卷 (TR) |
| ADR827ARMZ-REEL71 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Power, Precision Reference and Op Amp |
| ADR827BRMZ | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Power, Precision Reference and Op Amp |
| ADR827BRMZ-R2 | 功能描述:IC OPAMP GP R-R 1MHZ LP 10MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.028 V/µs 增益带宽积:105kHz -3db带宽:- 电流 - 输入偏压:3nA 电压 - 输入偏移:100µV 电流 - 电源:3.3µA 电流 - 输出 / 通道:12mA 电压 - 电源，单路/双路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:剪切带 (CT) 其它名称:OP481GRUZ-REELCT |
发布紧急采购，3分钟左右您将得到回复。