- 您现在的位置：买卖IC网 > PDF目录10378 > ADS8412IBPFBR (Texas Instruments)IC ADC 16BIT 2MSPS 48-TQFP PDF资料下载
参数资料
| 型号： | ADS8412IBPFBR |
| 厂商： | Texas Instruments |
| 文件页数： | 13/30页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 2MSPS 48-TQFP |
| 产品培训模块： | Data Converter Basics |
| 标准包装： | 1,000 |
| 位数： | 16 |
| 采样率（每秒）： | 2M |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 200mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-TQFP |
| 供应商设备封装： | 48-TQFP（7x7） |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 1 个差分，单极 |
| 配用： | 296-18385-ND - EVALUATION MODULE FOR ADS8412 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
www.ti.com
PRINCIPLES OF OPERATION
REFERENCE
ANALOG INPUT
ADS8412
SLAS384A – JUNE 2003 – REVISED DECEMBER 2004
The ADS8412 is a high-speed successive approximation register (SAR) analog-to-digital converter (ADC). The
architecture is based on charge redistribution, which inherently includes a sample/hold function. See Figure 29
for the application circuit for the ADS8412.
The conversion clock is generated internally. The conversion time of 400 ns is capable of sustaining a 2-MHz
throughput.
The analog input is provided to two input pins: +IN and –IN. When a conversion is initiated, the differential input
on these pins is sampled on the internal capacitor array. While a conversion is in progress, both inputs are
disconnected from any internal function.
The ADS8412 can operate with an external reference with a range from 3.9 V to 4.2 V. A 4.096-V internal
reference is included. When internal reference is used, pin 2 (REFOUT) should be connected to pin 1 (REFIN)
with an 0.1 F decoupling capacitor and 1 F storage capacitor between pin 2 (REFOUT) and pins 47 and 48
(REFM) (see Figure 33). The internal reference of the converter is double buffered. If an external reference is
used, the second buffer provides isolation between the external reference and the CDAC. This buffer is also
used to recharge all of the capacitors of the CDAC during conversion. Pin 2 (REFOUT) can be left unconnected
(floating) if external reference is used.
When the converter enters the hold mode, the voltage difference between the +IN and -IN inputs is captured on
the internal capacitor array. Both +IN and -IN input has a range of –0.2 V to Vref + 0.2 V. The input span(+IN –
(–IN)) is limited to –Vref to Vref.
The input current on the analog inputs depends upon a number of factors: sample rate, input voltage, and source
impedance. Essentially, the current into the ADS8412 charges the internal capacitor array during the sample
period. After this capacitance has been fully charged, there is no further input current. The source of the analog
input voltage must be able to charge the input capacitance (25 pF) to an 16-bit settling level within the acquisition
time (100 ns) of the device. When the converter goes into the hold mode, the input impedance is greater than 1
G
.
Care must be taken regarding the absolute analog input voltage. To maintain the linearity of the converter, the
+IN and –IN inputs and the span (+IN – (–IN)) should be within the limits specified. Outside of these ranges, the
converter's linearity may not meet specifications. To minimize noise, low bandwidth input signals with low-pass
filters should be used.
Care should be taken to ensure that the output impedance of the sources driving +IN and –IN inputs are
matched. If this is not observed, the two inputs could have different setting time. This may result in offset error,
gain error and linearity error which varies with temperature and input voltage.
A typical input circuit using TI's THS4503 is shown Figure 31. Input from a single-ended source may be
converted into differential signal for ADS8412 as shown in the figure. In case the source itself is differential then
THS4503 may be used in differential input and differential output mode.
20
相关PDF资料 |
PDF描述 |
|---|---|
| D38999/20WC98PBLC | CONN HSG RCPT 10POS WALL MT PINS |
| D38999/20WD18SNLC | CONN HSG RCPT 18POS WALL MT SCKT |
| D38999/20FD18BN | CONN HSG RCPT 18POS WALL MT SCKT |
| MS27467T13B8SLC | CONN HSG PLUG 8POS STRGHT SCKT |
| D38999/24WD19AN | CONN HSG RCPT 19POS JAM NUT PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADS8412IBPFBRG4 | 功能描述:模数转换器 - ADC 16 Bit 2MSPS Parallel RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| ADS8412IBPFBT | 功能描述:模数转换器 - ADC 16 Bit 2MSPS Parallel RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| ADS8412IBPFBT | 制造商:Texas Instruments 功能描述:IC ADC 16BIT 2MSPS ((NW)) |
| ADS8412IBPFBTG4 | 功能描述:模数转换器 - ADC 16 Bit 2MSPS Parallel RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| ADS8412IPFB | 制造商:Texas Instruments 功能描述:16 BIT 2MSPS PARALLEL ADC W/REF, PSEUDO BIPOLAR FULLY DIFFER - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。