- 您现在的位置：买卖IC网 > PDF目录19416 > ADT7461AARMZ-2RL (ON Semiconductor)IC TEMP SENSOR DGTL 2CH 8-MSOP PDF资料下载
参数资料
| 型号： | ADT7461AARMZ-2RL |
| 厂商： | ON Semiconductor |
| 文件页数： | 15/19页 |
| 文件大小： | 294K |
| 描述： | IC TEMP SENSOR DGTL 2CH 8-MSOP |
| 产品变化通告： | MFG CHG Notification ADI to ON Semi |
| 标准包装： | 3,000 |
| 功能： | 温度监控系统（传感器） |
| 传感器类型： | 内部和外部 |
| 感应温度： | 0°C ~ 127°C，-55°C ~ 150°C |
| 精确度： | ±3°C |
| 拓扑： | ADC，比较器，多路复用器，寄存器库 |
| 输出类型： | 2 线 SMBus? |
| 输出警报： | 是 |
| 输出风扇： | 是 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 120°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | Micro8? |
| 包装： | 带卷 (TR) |
ADT7461A
http://onsemi.com
15
The ADT7461A Interrupt System
The ADT7461A has two interrupt outputs, ALERT
and
THERM
. Both have different functions and behavior.
ALERT
is maskable and responds to violations of software
programmed temperature limits or an open-circuit fault on
the external diode. THERM
is intended as a fail-safe
interrupt output that cannot be masked.
If the external or local temperature exceeds the
programmed high temperature limits, or equals or exceeds
the low temperature limits, the ALERT
output is asserted
low. An open-circuit fault on the external diode also causes
ALERT
to assert. ALERT
is reset when serviced by a master
reading its device address, provided the error condition has
gone away and the status register has been reset.
The THERM
output asserts low if the external or local
temperature exceeds the programmed THERM
limits.
THERM
temperature limits should normally be equal to or
greater than the high temperature limits. THERM
is reset
automatically when the temperature falls back within the
THERM
limit. The external and local limits are set by
default to 85癈. A hysteresis value can be programmed; in
which case, THERM
resets when the temperature falls to the
limit value minus the hysteresis value. This applies to both
local and remote measurement channels. The power-on
hysteresis default value is 10癈, but this can be
reprogrammed to any value after powerup.
The hysteresis loop on the THERM
outputs is useful when
THERM
is used, for example, as an on/off controller for a
fan. The users system can be set up so that when THERM
asserts, a fan is switched on to cool the system. When
THERM
goes high again, the fan can be switched off.
Programming a hysteresis value protects from fan jitter,
where the temperature hovers around the THERM
limit, and
the fan is constantly switched.
Table 15. THERM
HYSTERESIS
THERM
Hysteresis
Binary Representation
0癈
0 000 0000
1癈
0 000 0001
10癈
0 000 1010
Figure 19 shows how the THERM
and ALERT
outputs
operate. The ALERT
output can be used as a SMBALERT
to signal to the host via the SMBus that the temperature has
risen. The user can use the THERM
output to turn on a fan
to cool the system, if the temperature continues to increase.
This method ensures that there is a fail-safe mechanism to
cool the system, without the need for host intervention.
Figure 19. Operation of the ALERT
and THERM
Interrupts
1005C
THERM
LIMIT
905C
805C
705C
605C
505C
405C
THERM
LIMIT HYSTERESIS
HIGH TEMP LIMIT
RESET BY MASTER
TEMPERATURE
1
2
3
4
ALERT
THERM
" If the measured temperature exceeds the high
temperature limit, the ALERT
output asserts low.
" If the temperature continues to increase and exceeds the
THERM
limit, the THERM
output asserts low. This can
be used to throttle the CPU clock or switch on a fan.
" The THERM
output deasserts (goes high) when the
temperature falls to THERM
limit minus hysteresis. In ,
the default hysteresis value of 10癈 is shown.
" The ALERT
output deasserts only when the
temperature has fallen below the high temperature
limit, and the master has read the device address and
cleared the status register.
" Pin 6 on the ADT7461A can be configured as either an
ALERT
output or as an additional THERM
output.
" THERM2
asserts low when the temperature exceeds the
programmed local and/or remote high temperature
limits. It is reset in the same manner as THERM
and is
not maskable.
" The programmed hysteresis value also applies to
THERM2
.
Figure 20 shows how THERM
and THERM2
operate
together to implement two methods of cooling the system.
In this example, the THERM2
limits are set lower than the
THERM
limits. The THERM2
output is used to turn on a
fan. If the temperature continues to rise and exceeds the
THERM
limits, the THERM
output provides additional
cooling by throttling the CPU.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B3B-EU-B1 | CONVERTER MOD DC/DC 95V 200W |
| B82496C3479J | INDUCTOR 4.7NH .8A 0603 5% |
| ECC12DCAT | CONN EDGECARD 24POS R/A .100 SLD |
| VI-BWW-CY-F1 | CONVERTER MOD DC/DC 5.5V 50W |
| VE-B32-EU-B1 | CONVERTER MOD DC/DC 15V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADT7461AARMZ2RL7 | 功能描述:板上安装温度传感器 1 TMP DIO MON W/SMBUS ITF RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| ADT7461AARMZ-2RL7 | 功能描述:IC SENSOR TEMP DGTL 2CH 8-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| ADT7461AARMZ-R | 功能描述:板上安装温度传感器 1 TMP DIO MON W/SMBUS ITF RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| ADT7461AARMZ-REEL | 功能描述:IC SENSOR TEMP DGTL 2CH 8-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| ADT7461AARMZ-REEL7 | 功能描述:IC SENSOR TEMP DGTL 2CH 8-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
发布紧急采购，3分钟左右您将得到回复。