- 您现在的位置：买卖IC网 > PDF目录22030 > ADT7461ARMZ-2REEL (ON Semiconductor)IC SENSOR TEMP DGTL 2CH 8MSOP PDF资料下载
参数资料
| 型号： | ADT7461ARMZ-2REEL |
| 厂商： | ON Semiconductor |
| 文件页数： | 7/20页 |
| 文件大小： | 268K |
| 描述： | IC SENSOR TEMP DGTL 2CH 8MSOP |
| 产品变化通告： | MFG CHG Notification ADI to ON Semi |
| 标准包装： | 3,000 |
| 功能： | 温度监控系统（传感器） |
| 传感器类型： | 内部和外部 |
| 感应温度： | 0°C ~ 127°C，-55°C ~ 150°C |
| 精确度： | ±3°C |
| 拓扑： | ADC，比较器，多路复用器，寄存器库 |
| 输出类型： | 2 线 SMBus? |
| 输出警报： | 是 |
| 输出风扇： | 是 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 120°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | Micro8? |
| 包装： | 带卷 (TR) |
ADT7461
http://onsemi.com
7
Functional Description
The ADT7461 is a local and remote temperature sensor
and over/under temperature alarm, with the added ability to
automatically cancel the effect of 3 kW (typical) of
resistance in series with the temperature monitoring diode.
When the ADT7461 is operating normally, the on-board
ADC operates in a free-running mode. The analog input
multiplexer alternately selects either the on-chip
temperature sensor to measure its local temperature or the
remote temperature sensor. The ADC digitizes these signals
and the results are stored in the local and remote temperature
value registers.
The local and remote measurement results are compared
with the corresponding high, low, and THERM
temperature
limits, stored in eight on-chip registers. Out-of-limit
comparisons generate flags that are stored in the status register.
A result that exceeds the high temperature limit, the low
temperature limit, or an external diode fault causes the ALERT
output to assert low. Exceeding THERM
temperature limits
causes the THERM
output to assert low. The ALERT
output
can be reprogrammed as a second THERM
output.
The limit registers can be programmed and the device
controlled and configured via the serial SMBus. The
contents of any register can also be read back via the SMBus.
Control and configuration functions consist of switching
the device between normal operation and standby mode,
selecting the temperature measurement scale, masking or
enabling the ALERT
output, switching Pin 6 between
ALERT
and THERM2
, and selecting the conversion rate.
Series Resistance Cancellation
Parasitic resistance to the D+ and D inputs to the
ADT7461, seen in series with the remote diode, is caused by
a variety of factors, including PCB track resistance and track
length. This series resistance appears as a temperature offset
in the remote sensors temperature measurement. This error
typically causes a 0.5癈 offset per ohm of parasitic resistance
in series with the remote diode.
The ADT7461 automatically cancels out the effect of this
series resistance on the temperature reading, giving a more
accurate result, without the need for user characterization of
this resistance. The ADT7461 is designed to automatically
cancel typically up to 3 kW of resistance. By using an
advanced temperature measurement method, this is
transparent to the user. This feature allows resistances to be
added to the sensor path to produce a filter, allowing the part
to be used in noisy environments. See the Noise Filtering
section for more details.
Temperature Measurement Method
A simple method of measuring temperature is to exploit
the negative temperature coefficient of a diode by measuring
the base-emitter voltage (V
BE
) of a transistor operated at
constant current. However, this technique requires
calibration to null out the effect of the absolute value of V
BE
,
which varies from device to device.
The technique used in the ADT7461 is to measure the
change in V
BE
when the device is operated at three different
currents. Previous devices have used only two operating
currents, but it is the use of a third current that allows
automatic cancellation of resistances in series with the
external temperature sensor.
Figure 15 shows the input signal conditioning used to
measure the output of an external temperature sensor. This
figure shows the external sensor as a substrate transistor, but
it could equally be a discrete transistor. If a discrete
transistor is used, the collector will not be grounded and
should be linked to the base. To prevent ground noise
interfering with the measurement, the more negative
terminal of the sensor is not referenced to ground, but is
biased above ground by an internal diode at the D input. C1
may be added as a noise filter (a recommended maximum
value of 1,000 pF). However, a better option in noisy
environments is to add a filter, as described in the Noise
Filtering section. See the Layout Considerations section for
more information on C1.
To measure DV
BE
, the operating current through the
sensor is switched among three related currents. Figure 15
shows N1 ?I and N2 ?I as different multiples of the
current, I. The currents through the temperature diode are
switched between I and N1 ?I, giving DV
BE1
, and then
between I and N2 ?I, giving DV
BE2
. The temperature may
then be calculated using the two DV
BE
measurements. This
method can also be shown to cancel the effect of any series
resistance on the temperature measurement.
The resulting DV
BE
waveforms are passed through a
65 kHz low-pass filter to remove noise and then to a
chopper-stabilized amplifier. This amplifies and rectifies the
waveform to produce a dc voltage proportional to DV
BE
. The
ADC digitizes this voltage and a temperature measurement is
produced. To reduce the effects of noise, digital filtering is
performed by averaging the results of 16 measurement cycles
for low conversion rates. At rates of 16, 32, and 64
conversions per second, no digital averaging takes place.
Signal conditioning and measurement of the internal
temperature sensor is performed in the same manner.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-BWF-CV-F2 | CONVERTER MOD DC/DC 72V 150W |
| NCP1086T-ADJ | IC REG LDO ADJ 1.5A TO220AB |
| ADT7467ARQZ | IC PWM FAN CTRLR W/MONITR 16QSOP |
| D09P13A4PL00LF | CONN DSUB PLUG 9 POS R/A GOLD |
| VE-BWD-CV-F3 | CONVERTER MOD DC/DC 85V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADT7461ARMZ-2REEL7 | 功能描述:IC SENSOR TEMP DGTL 2CH 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| ADT7461ARMZ-2RL7 | 功能描述:板上安装温度传感器 EXT TMP RGE IC 1C TDM SRC RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| ADT7461ARMZ-R2 | 制造商:ON Semiconductor 功能描述:ADT7461ARMZ-2REEL |
| ADT7461ARMZ-R7 | 功能描述:板上安装温度传感器 EXT TMP RGE IC 1C TDM SRC RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| ADT7461ARMZ-REEL | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:?±1a?? Temperature Monitor with Series Resistance Cancellation |
发布紧急采购，3分钟左右您将得到回复。