- 您现在的位置：买卖IC网 > PDF目录22034 > ADT7467ARQ-REEL (ON Semiconductor)IC REMOTE THERMAL CTRLR 16-QSOP PDF资料下载
参数资料
| 型号： | ADT7467ARQ-REEL |
| 厂商： | ON Semiconductor |
| 文件页数： | 8/72页 |
| 文件大小： | 0K |
| 描述： | IC REMOTE THERMAL CTRLR 16-QSOP |
| 产品变化通告： | MFG CHG Notification ADI to ON Semi Product Obsolescence 11/Feb/2009 |
| 标准包装： | 2,500 |
| 系列： | dBCool® |
| 功能： | 风扇控制，温度监控器 |
| 传感器类型： | 内部和外部 |
| 感应温度： | -40°C ~ 120°C，外部传感器 |
| 精确度： | ±1.5°C |
| 拓扑： | ADC，比较器，风扇速度计数器，多路复用器，寄存器库 |
| 输出类型： | SMBus? |
| 输出警报： | 无 |
| 输出风扇： | 是 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 120°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页
ADT7467
Product Description
The ADT7467 is a complete thermal monitor and multiple
fan controller for systems requiring thermal monitoring and
cooling. The device communicates with the system via a
serial system management bus. The serial bus controller has
a serial data line for reading and writing addresses and data
(Pin 16) and an input line for the serial clock (Pin 1). All
control and programming functions for the ADT7467 are
performed over the serial bus. In addition, one of two pins
can be reconfigured as an SMBALERT output to signal
out-of-limit conditions.
Comparison between ADT7460 and ADT7467
The ADT7467 is an upgrade from the ADT7460. The
ADT7467 and ADT7460 are almost pin and register map
compatible. The ADT7467 and ADT7460 have the
following differences:
1. On the ADT7467, the PWM drive signals can be
configured as either high frequency or low
frequency drives. The low frequency option is
programmable between 10 Hz and 100 Hz. The
high frequency option is 22.5 kHz. On the
ADT7460, only the low frequency option is
available.
2. Once V CC and V CCP are powered up, monitoring
of temperature and fan speeds is enabled on the
ADT7467. If V CCP is never powered up,
monitoring is enabled when the first SMBus
transaction with the ADT7467 is complete. On the
ADT7460, the STRT bit in Configuration Register
1 must be set to enable monitoring.
3. The fans are switched off by default upon
power-up of the ADT7467. On the ADT7460, the
fans run at full speed upon power-up.
Fail-safe cooling is provided on the ADT7467. If
the measured temperature exceeds the THERM
limit (100 ? C), the fans run at full speed.
Fail-safe cooling is also provided 4.6 sec after
V CCP is powered up. The fans operate at full speed
if the ADT7467 has not been addressed via the
SMBus within 4.6 sec of when the V CCP is
powered up. This protects the system in the event
that the SMBus fails. The ADT7467 can be
programmed at any time, and it behaves as
programmed. If V CCP is never powered up,
fail-safe cooling is effectively disabled. If V CCP is
disabled, writing to the ADT7467 at any time
causes the ADT7467 to operate normally.
4. Series resistance cancellation (SRC) is provided
on the remote temperature channels on the
ADT7467, but not on the ADT7460. SRC
automatically cancels linear offset introduced by a
series resistance between the thermal diode and the
sensor.
5. The ADT7467 has an extended temperature
measurement range. The measurement range goes
from ? 64 ? C to +191 ? C. On the ADT7460, the
measurement range is from ? 127 ? C to +127 ? C.
This means that the ADT7467 can measure higher
temperatures. The ADT7467 also includes the
ADT7460 temperature range; the temperature
measurement range can be switched by setting
Bit 0 of Configuration Register 5.
6. The ADT7467 maximum fan speed (% duty cycle)
in the automatic fan speed control loop can be
programmed. The maximum fan speed is 100%
duty cycle on the ADT7460 and is not
programmable.
7. The offset register in the ADT7467 is
programmable up to ? 64 ? C with 0.50 ? C
resolution. The offset register of the ADT7460 is
programmable up to ? 32 ? C with 0.25 ? C
resolution.
8. V CCP is monitored on Pin 14 of the ADT7467 and
can be used to set the threshold for THERM
(PROCHOT) (2/3 of V CCP ). 2.5 V is monitored on
Pin 14 o f the ADT7460. The threshold for
THERM (PROCHOT) is set at V IH = 1.7 V and
V IL = 0.8 V on the ADT7460.
9. On the ADT7460, Pin 14 could be reconfigured as
SMBALERT. This is not available on the ADT7467.
SMBALERT can be enabled instead on Pin 9.
10. A GPIO can also be made available on Pin 9 on the
ADT7467. This is not available on the ADT7460.
Set the GPIO polarity and direction in Configuration
Register 5. The GPIO status bit is Bit 5 of Status
Register 2 (it is shared with TACH4 and THERM
because only one can be enabled at a time).
11. The ADT7460 has three possible SMBus
addresses, which are selectable using the address
select and address enable pins. The ADT7467 has
one SMBus address available at Address 0x2E.
Due to the inclusion of extra functionality, the register
map has changed, including an additional configuration
register, Configuration Register 5 at Address 0x7C.
Configuration Register 5
Bit 0: If Bit 0 is set to 1, the ADT7467, in terms of
temperature, is backward compatible with the ADT7460.
Measurements, including T MIN calibration circuit and fan
control, work in the range ? 127 ? C to +127 ? C. In addition,
care should be taken in reprogramming the temperature
limits (T MIN , operating point, THERM) to their desired twos
complement value, because the power-on default for them
is at Offset 64. The extended temperature range is ? 64 ? C to
191 ? C. The default is 1, which is in the ? 64 ? C to +191 ? C
temperature range.
Bit 1 = 0 is the high frequency (22.5 kHz) fan drive signal.
Bit 1 = 1 switches the fan drive to low frequency PWM,
programmable between 10 Hz and 100 Hz, the same as the
ADT7460. The default is 0, or HF PWM.
http://onsemi.com
8
相关PDF资料 |
PDF描述 |
|---|---|
| ADT7467ARQ | IC PWM FAN CTRLR W/MONITR 16QSOP |
| ADM1026JST-REEL7 | IC CNTRL SYS REF/EEPROM 48LQFP |
| EP1K30TC144-3N | IC ACEX 1K FPGA 30K 144-TQFP |
| 7-1624113-2 | INDUCTOR 2.7UH 5% 0805 |
| EP1K30TC144-3 | IC ACEX 1K FPGA 30K 144-TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADT7467ARQ-REEL7 | 功能描述:IC REMOTE THERMAL CTRLR 16-QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:dBCool® 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| ADT7467ARQZ | 功能描述:马达/运动/点火控制器和驱动器 FAN CNTRLR/INT MON RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| ADT7467ARQZ | 制造商:Analog Devices 功能描述:Temperature Sensor IC |
| ADT7467ARQZ-R7 | 功能描述:板上安装温度传感器 RMT THRM MON FAN CTL RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| ADT7467ARQZ-REEL | 功能描述:板上安装温度传感器 FAN CNTRLR/INT MON RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。