参数资料
型号: ADT7476AARQZ
厂商: ON Semiconductor
文件页数: 62/66页
文件大小: 945K
描述: IC REMOTE THERM CTRLR 5V 24QSOP
产品变化通告: MFG CHG Notification ADI to ON Semi
QSOP 24ld Pkg (MSL) Change 17/Jun/2010
Product Discontinuation 30/Sept/2011
标准包装: 56
系列: dBCool®
功能: 风扇控制,温度监控器
传感器类型: 内部和外部
感应温度: -40°C ~ 125°C
精确度: ±2.5%
拓扑: ADC,比较器,风扇速度计数器,多路复用器,寄存器库
输出类型: SMBus?
输出警报:
输出风扇:
电源电压: 3 V ~ 3.6 V
工作温度: -40°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 24-SSOP(0.154",3.90mm 宽)
供应商设备封装: 24-QSOP
包装: 管件
产品目录页面: 1118 (CN2011-ZH PDF)
ADT7476A
http://onsemi.com
62
Table 82. REGISTER 0x78  CONFIGURATION REGISTER 3 (POWER-ON DEFAULT = 0x00) (Note 1)
Bit No.
Mnemonic
R/W
Description
[0]
ALERT
R/W
ALERT = 1, Pin 10 (PWM2/SMBALERT
) is configured as an SMBALERT
 interrupt output to
indicate out-of-limit error conditions.
ALERT = 0, Pin 10 (PWM2/SMBALERT
) is configured as the PWM2 output.
[1]
THERM
/
2.5V
R/W
THERM
= 1 enables THERM
 functionality on Pin 22 and Pin 14, if Pin 14 is configured as
THERM
, determined by Bits 0 and 1 (PIN14FUNC) of Configuration Register 4. When THERM
is asserted, if the fans are running and the BOOST bit is set, then the fans run at full speed.
Alternatively, THERM
 can be programmed so that a timer is triggered to time how long THERM
has been asserted.
THERM
= 0 enables 2.5V measurement on Pin 22 and disables THERM
. If Bits [5:7] of
Configuration Register 5 are set, THERM
 is bidirectional. If they are 0, THERM
 is a timer input
only.
Pin14FUNC
THERM
/2.5 V
Pin 22
Pin 14
00
01
10
11
00
01
10
11
0
0
0
0
1
1
1
1
+2.5 V
IN
+2.5 V
IN
+2.5 V
IN
+2.5 V
IN
THERM
+2.5 V
IN
THERM
THERM
TACH4
THERM
SMBALERT
GPIO6
TACH4
THERM
SMBALERT
GPIO6
[2]
BOOST
R/W
When THERM
 is an input and BOOST = 1, assertion of THERM
 causes all fans to run at the
maximum programmed duty cycle for fail-safe cooling.
[3]
FAST
R/W
FAST = 1 enables fast TACH measurements on all channels. This increases the TACH
measurement rate from once per second to once every 250 ms (4x).
[4]
DC1
R/W
DC1 = 1 enables TACH measurements to be continuously made on TACH1. Fans must be
driven by dc. Setting this bit prevents pulse stretching because it is not required for dc-driven
motors.
[5]
DC2
R/W
DC2 = 1 enables TACH measurements to be continuously made on TACH2. Fans must be
driven by dc. Setting this bit prevents pulse stretching because it is not required for dc-driven
motors.
[6]
DC3
R/W
DC3 = 1 enables TACH measurements to be continuously made on TACH3. Fans must be
driven by dc. Setting this bit prevents pulse stretching because it is not required for dc-driven
motors.
[7]
DC4
R/W
DC4 = 1 enables TACH measurements to be continuously made on TACH4. Fans must be
driven by dc. Setting this bit prevents pulse stretching because it is not required for dc-driven
motors.
1.  This register become read-only when the Configuration Register 1 Lock bit is set to 1. Any further attempts to write to to this register have no
effect.
Table 83. REGISTER 0x79  THERM
 TIMER STATUS REGISTER (POWER-ON DEFAULT = 0x00)
Bit No.
Mnemonic
R/W
Description
[7:1]
TMR
Read-only
Times how long THERM
 input is asserted. These seven bits read 0 until the THERM
assertion time exceeds 45.52 ms.
[0]
ASRT/
TMR0
Read-only
This bit is set high on the assertion of the THERM
 input and is cleared on read. If the THERM
assertion time exceeds 45.52 ms, this bit is set and becomes the LSB of the 8-bit TMR
reading. This allows THERM
 assertion times from 45.52 ms to 5.82 sec to be reported back
with a resolution of 22.76 ms.
Table 84. REGISTER 0x7A  THERM
 TIMER LIMIT REGISTER (POWER-ON DEFAULT = 0x00)
Bit No.
Mnemonic
R/W
Description
[7:0]
LIMT
R/W
Sets maximum THERM
 assertion length allowed before an interrupt is generated. This is an
8-bit limit with a resolution of 22.76 ms allowing THERM
 assertion limits of 45.52 ms to
5.82 sec to be programmed. If the THERM
 assertion time exceeds this limit, Bit 5 (F4P) of
Interrupt Status Register 2 (0x42) is set. If the limit value is 0x00, an interrupt is generated
immediately on the assertion of the THERM
 input.
相关PDF资料
PDF描述
ADM1032ARZ-1 IC TEMP MONITOR 108DEG 8SOIC
VI-J3F-CW CONVERTER MOD DC/DC 72V 100W
D09S13A6GV00LF CONN DSUB RCPT 9 POS R/A GOLD
TAJC686K016H CAP TANT 68UF 16V 10% 2312
VI-J3D-CW CONVERTER MOD DC/DC 85V 100W
相关代理商/技术参数
参数描述
ADT7476AARQZ-R 功能描述:板上安装温度传感器 MONITORS 5V/4 FANS RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
ADT7476AARQZ-REEL 功能描述:IC REMOTE THERMAL CTRLR 24-QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:dBCool® 标准包装:1 系列:- 功能:温度监控系统(传感器) 传感器类型:内部和外部 感应温度:-40°C ~ 125°C,外部传感器 精确度:±2.5°C 本地(最大值),±5°C 远程(最大值) 拓扑:ADC,比较器,寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6
ADT7476AARQZ-REEL7 功能描述:IC REMOTE THERMAL CTRLR 24-QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:dBCool® 标准包装:1 系列:- 功能:温度监控系统(传感器) 传感器类型:内部和外部 感应温度:-40°C ~ 125°C,外部传感器 精确度:±2.5°C 本地(最大值),±5°C 远程(最大值) 拓扑:ADC,比较器,寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6
ADT7476AARQZ-RL7 功能描述:板上安装温度传感器 MONITORS 5V/4 FANS RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
ADT7476ARQH 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:dBCOOL Remote Thermal Controller and Voltage Monitor