- 您现在的位置：买卖IC网 > PDF目录11199 > ADUC816BSZ-REEL (Analog Devices Inc)IC MCU FLASH 16BIT ADC 52MQFP PDF资料下载
参数资料
| 型号： | ADUC816BSZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 35/68页 |
| 文件大小： | 0K |
| 描述： | IC MCU FLASH 16BIT ADC 52MQFP |
| 标准包装： | 800 |
| 系列： | MicroConverter® ADuC8xx |
| 核心处理器： | 8052 |
| 芯体尺寸： | 8-位 |
| 速度： | 12.58MHz |
| 连通性： | I²C，SPI，UART/USART |
| 外围设备： | PSM，温度传感器，WDT |
| 输入/输出数： | 34 |
| 程序存储器容量： | 8KB（8K x 8） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 640 x 8 |
| RAM 容量： | 256 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.7 V ~ 5.5 V |
| 数据转换器： | A/D 7x16b; D/A 1x12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 52-QFP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页当前第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页
REV. 0
ADuC816
–40–
Flash/EE Memory Timing
The typical program/erase times for the Flash/EE Data
Memory are:
Erase Full Array (640 Bytes) – 2 ms
Erase Single Page (4 Bytes) – 2 ms
Program Page (4 Bytes) – 250
μs
Read Page (4 Bytes) – Within Single Instruction Cycle
Using the Flash/EE Memory Interface
As with all Flash/EE memory architectures, the array can be pro-
grammed in-system at a byte level, although it must be erased
first; the erasure being performed in page blocks (4-byte pages
in this case).
A typical access to the Flash/EE Data array will involve setting
up the page address to be accessed in the EADRL SFR, config-
uring the EDATA1–4 with data to be programmed to the array
(the EDATA SFRs will not be written for read accesses) and
finally, writing the ECON command word which initiates one
of the six modes shown in Table XIII.
It should be noted that a given mode of operation is initiated as
soon as the command word is written to the ECON SFR. The
core microcontroller operation on the ADuC816 is idled until the
requested Program/Read or Erase mode is completed.
In practice, this means that even though the Flash/EE memory
mode of operation is typically initiated with a two-machine cycle
MOV instruction (to write to the ECON SFR), the next instruc-
tion will not be executed until the Flash/EE operation is complete
(250
μs or 2 ms later). This means that the core will not respond
to Interrupt requests until the Flash/EE operation is complete,
although the core peripheral functions like Counter/Timers will
continue to count and time as configured throughout this period.
Erase-All
Although the 640-byte User Flash/EE array is shipped from the
factory pre-erased, i.e., Byte locations set to FFH, it is nonethe-
less good programming practice to include an erase-all routine as
part of any configuration/setup code running on the ADuC816.
An “ERASE-ALL” command consists of writing “06H” to the
ECON SFR, which initiates an erase of all 640 byte locations in
the Flash/EE array. This command coded in 8051 assembly would
appear as:
MOV ECON, #06H
; Erase all Command
; 2 ms Duration
Program a Byte
In general terms, a byte in the Flash/EE array can only be pro-
grammed if it has previously been erased. To be more specific, a
byte can only be programmed if it already holds the value FFH.
Because of the Flash/EE architecture, this erasure must happen
at a page level; therefore, a minimum of four bytes (1 page) will
be erased when an erase command is initiated.
A more specific example of the Program-Byte process is shown
below. In this example the user writes F3H into the second
byte on Page 03H of the Flash/EE Data Memory space while
preserving the other three bytes already in this page. As the user
is only required to modify one of the page bytes, the full page must
be first read so that this page can then be erased without the exist-
ing data being lost.
This example, coded in 8051 assembly, would appear as:
MOV EADRL,#03H
; Set Page Address Pointer
MOV ECON,#01H
; Read Page
MOV EDATA2,#0F3H ; Write New Byte
MOV ECON,#05H
; Erase Page
MOV ECON,#02H
; Write Page (Program Flash/EE)
REV. A
相关PDF资料 |
PDF描述 |
|---|---|
| NLVAS4599DFT2G | IC SWITCH SPDT SC88 |
| ADUC845BSZ8-5-RL | IC FLASH MCU W/24BIT ADC 56-CSP |
| MC74HCT4051ADG | ANALOG MULTIPLEXERS/DEMU SOIC16 |
| ADUC7036DCPZ | IC MCU 96K FLASH DUAL 48LFCSP |
| MC74HC4051ADTR2G | IC MUX/DEMUX 8X1 16TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC824 | 制造商:AD 制造商全称:Analog Devices 功能描述:MicroConverter, Dual-Channel 16-/24-Bit ADCs with Embedded FLASH MCU |
| ADUC824BCP | 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 8KB Flash 3.3V/5V 56-Pin LFCSP EP 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 8KB FLASH 12.58MHZ 3.3/5V 56LFCSP - Bulk |
| ADUC824BCP-REEL | 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 8KB Flash 3.3V/5V 56-Pin LFCSP EP T/R |
| ADUC824BCPZ | 功能描述:IC MCU 8K FLASH ADC/DAC 56LFCSP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
| ADUC824BS | 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 8KB Flash 3.3V/5V 52-Pin MQFP 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 8KB FLASH 12.58MHZ 3.3/5V 52MQFP - Bulk 制造商:Analog Devices 功能描述:8BIT MCU +24BIT ADC LQFP52 824 |
发布紧急采购，3分钟左右您将得到回复。