- 您现在的位置：买卖IC网 > PDF目录21381 > ADUM2402CRWZ-RL (Analog Devices Inc)IC ISOLATOR DIGITAL QUAD 16SOIC PDF资料下载
参数资料
| 型号： | ADUM2402CRWZ-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 18/24页 |
| 文件大小： | 0K |
| 描述： | IC ISOLATOR DIGITAL QUAD 16SOIC |
| 标准包装： | 1,000 |
| 系列： | iCoupler® |
| 输入 - 1 侧/2 侧： | 2/2 |
| 通道数： | 4 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 电压 - 隔离： | 5000Vrms |
| 数据速率： | 120Mbps |
| 传输延迟： | 27ns |
| 输出类型： | 逻辑 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC W |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 105°C |
ADuM2400/ADuM2401/ADuM2402
APPLICATION INFORMATION
PC BOARD LAYOUT
The ADuM240x digital isolator requires no external interface
circuitry for the logic interfaces. Power supply bypassing is
strongly recommended at the input and output supply pins (see
Figure 17). Bypass capacitors are most conveniently connected
between Pin 1 and Pin 2 for V DD1 and between Pin 15 and Pin 16
for V DD2 . The capacitor value should be between 0.01 μF and 0.1 μF.
The total lead length between both ends of the capacitor and
the input power supply pin should not exceed 20 mm. Bypassing
between Pin 1 and Pin 8 and between Pin 9 and Pin 16 should
be considered unless the ground pair on each package side are
connected close to the package.
Data Sheet
DC CORRECTNESS AND MAGNETIC FIELD IMMUNITY
Positive and negative logic transitions at the isolator input cause
narrow (~1 ns) pulses to be sent via the transformer to the decoder.
The decoder is bistable and is therefore either set or reset by the
pulses, indicating input logic transitions. In the absence of logic
transitions at the input for more than ~1 μs, a periodic set of
refresh pulses indicative of the correct input state are sent to
ensure dc correctness at the output. If the decoder receives no
internal pulses for more than approximately 5 μs, the input side
is assumed to be without power or nonfunctional; in which
case, the isolator output is forced to a default state (see Table 11)
by the watchdog timer circuit.
V DD1
GND 1
V IA
V IB
V IC/ V OC
V ID/ V OD
V DD2
GND 2
V OA
V OB
V OC/ V IC
V OD/ V ID
The limitation on the ADuM240x’s magnetic field immunity is
set by the condition in which induced voltage in the transformer’s
receiving coil is large enough to either falsely set or reset the
decoder. The following analysis defines the conditions under
V E1 V E2
GND 1 GND 2
Figure 17. Recommended Printed Circuit Board Layout
In applications involving high common-mode transients, ensure
that board coupling across the isolation barrier is minimized.
Furthermore, the board layout should be designed such that
any coupling that does occur equally affects all pins on a given
component side. Failure to ensure this could cause voltage
differentials between pins exceeding the device’s Absolute
Maximum Ratings, thereby leading to latch-up or permanent
damage.
See the AN-1109 Application Note for board layout guidelines.
PROPAGATION DELAY-RELATED PARAMETERS
Propagation delay is a parameter that describes the length of time
it takes for a logic signal to propagate through a component.
The propagation delay to a logic low output can differ from the
propagation delay to logic high.
which this can occur. The 3 V operating condition of the
ADuM240x is examined because it represents the most
susceptible mode of operation.
The pulses at the transformer output have an amplitude greater
than 1.0 V. The decoder has a sensing threshold at about 0.5 V,
therefore establishing a 0.5 V margin in which induced voltages
can be tolerated. The voltage induced across the receiving coil is
given by
V = (? dβ / dt )Σ∏r n2 ; n = 1, 2,…, N
where:
β is the magnetic flux density (gauss).
N is the number of turns in the receiving coil.
r n is the radius of the n th turn in the receiving coil (cm).
Given the geometry of the receiving coil in the ADuM240x and
an imposed requirement that the induced voltage be at most
50% of the 0.5 V margin at the decoder, a maximum allowable
magnetic field is calculated as shown in Figure 19.
INPUT (V Ix )
OUTPUT (V Ox )
50%
t PLH
t PHL
50%
Figure 18. Propagation Delay Parameters
100
10
1
Pulse width distortion is the maximum difference between these
two propagation delay values and is an indication of how
accurately the input signal’s timing is preserved.
Channel-to-channel matching refers to the maximum amount
the propagation delay differs among channels within a single
ADuM240x component.
0.1
0.01
Propagation delay skew refers to the maximum amount the
0.001
1k
10k
100k
1M
10M
100M
propagation delay differs among multiple ADuM240x components
operated under the same conditions.
Rev. E | Page 18 of 24
MAGNETIC FIELD FREQUENCY (Hz)
Figure 19. Maximum Allowable External Magnetic Flux Density
相关PDF资料 |
PDF描述 |
|---|---|
| SMCJ64CA | DIODE TVS 64V 1500W BI 5% SMD |
| 11K5014-JCNG | KNOB PLASTIC .125 DIA GRAY |
| 6-353293-4 | MINI CT MT REC ASSY 14P BLUR |
| ADUM2400ARWZ | IC ISOLATOR DIGITAL QUAD 16SOIC |
| 281783-3 | PLUG HE14 IDC 180 3 P AWG 26-24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUM2402XAZ | 制造商:Analog Devices 功能描述:QUAD-CHANNEL DIGITAL ISOLATORS - Bulk |
| ADUM2402XBZ | 制造商:Analog Devices 功能描述:QUAD-CHANNEL DIGITAL ISOLATORS - Bulk |
| ADUM2402XCZ | 制造商:Analog Devices 功能描述:QUAD-CHANNEL DIGITAL ISOLATORS - Bulk |
| ADUM240D0BRIZ | 功能描述:General Purpose Digital Isolator 5000Vrms 4 Channel 150Mbps 75kV/μs CMTI 16-SOIC (0.295", 7.50mm Width) 制造商:analog devices inc. 系列:iCoupler? 包装:带卷（TR） 零件状态:有效 技术:磁耦合 类型:通用 隔离式电源:无 通道数:4 输入 - 输入侧 1/输入侧 2:3/1 通道类型:单向 电压 - 隔离:5000Vrms 共模瞬态抗扰度（最小值）:75kV/μs 数据速率:150Mbps 传播延迟 tpLH / tpHL（最大值）:13ns，13ns 脉宽失真（最大）:3ns 上升/下降时间（典型值）:2.5ns，2.5ns 电压 - 电源:1.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商器件封装:16-SOIC 标准包装:37 |
| ADUM240D0BRIZ-RL | 功能描述:General Purpose Digital Isolator 5000Vrms 4 Channel 150Mbps 75kV/μs CMTI 16-SOIC (0.295", 7.50mm Width) 制造商:analog devices inc. 系列:iCoupler? 包装:带卷（TR） 零件状态:有效 技术:磁耦合 类型:通用 隔离式电源:无 通道数:4 输入 - 输入侧 1/输入侧 2:4/0 通道类型:单向 电压 - 隔离:5000Vrms 共模瞬态抗扰度（最小值）:75kV/μs 数据速率:150Mbps 传播延迟 tpLH / tpHL（最大值）:13ns，13ns 脉宽失真（最大）:3ns 上升/下降时间（典型值）:2.5ns，2.5ns 电压 - 电源:1.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商器件封装:16-SOIC 标准包装:1,000 |
发布紧急采购，3分钟左右您将得到回复。