- 您现在的位置：买卖IC网 > PDF目录21443 > ADUM4160BRIZ (Analog Devices Inc)IC USB ISOLATOR FULL/LOW 16SOIC PDF资料下载
参数资料
| 型号： | ADUM4160BRIZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/16页 |
| 文件大小： | 0K |
| 描述： | IC USB ISOLATOR FULL/LOW 16SOIC |
| 产品培训模块： | iCoupler Digital Isolater Technology |
| 标准包装： | 37 |
| 系列： | iCoupler® |
| 输入 - 1 侧/2 侧： | 2/2 |
| 通道数： | 2 |
| 电源电压： | 3.1 V ~ 5.5 V |
| 电压 - 隔离： | 5000Vrms |
| 数据速率： | 12Mbps |
| 传输延迟： | 60ns |
| 输出类型： | 逻辑 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC-IC |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 105°C |
Data Sheet
COMPATIBILITY OF UPSTREAM APPLICATIONS
The ADuM4160 is designed specifically for isolating a USB
peripheral. However, the chip does have two USB interfaces that
meet the electrical requirements for driving USB cables. This
opens the possibility of implementing isolation in downstream
USB ports such as isolated cables, which have generic connections
to both upstream and downstream devices, as well as isolating
host ports.
In a fully compliant application, a downstream facing port must
be able to detect whether a peripheral is low speed or full speed
based on the application of the upstream pull-up. The buffers and
logic conventions must adjust to match the requested speed.
Because the ADuM4160 sets its speed by hard wiring pins, the
part cannot adjust to different peripherals on the fly.
ADuM4160
PRINTED CIRCUIT BOARD (PCB) LAYOUT
The ADuM4160 digital isolator requires no external interface
circuitry for the logic interfaces. For full speed operation, the
D+ and D? line on each side of the device requires a 24 Ω ± 1%
series termination resistor. These resistors are not required for
low speed applications. Power supply bypassing is required at
the input and output supply pins ( see Figure 5). Install bypass
capacitors between V BUSx and V DDx on each side of the chip. The
capacitor value should have a value of 0.1 μF and be of a low
ESR type. The total lead length between both ends of the
capacitor and the power supply pin should not exceed 10 mm.
Bypassing between Pin 2 and Pin 8 and between Pin 9 and
Pin 15 should also be considered, unless the ground pair on
each package side is connected close to the package.
V BUS1 = 5.0V INPUT V BUS2 = 3.3V INPUT
The practical result of using the ADuM4160 in a host port is
that the port works at a single speed. This behavior is acceptable
V DD1 = 3.3V OUTPUT
V BUS1
GND 1
V DD2 = 3.3V INPUT
V BUS2
GND 2
in embedded host applications; however, this type of interface is
not fully compliant as a general-purpose USB port.
Isolated cable applications have a similar issue. The cable operates
at the preset speed only; therefore, treat cable assemblies as
V DD1
PDEN
SPU
UD–
UD+
GND 1
ADuM4160
V DD2
SPD
PIN
DD–
DD+
GND 2
custom applications, not general-purpose isolated cables.
POWER SUPPLY OPTIONS
In most USB transceivers, 3.3 V is derived from the 5 V USB bus
through an LDO regulator. The ADuM4160 includes internal
LDO regulators on both the upstream and downstream sides.
The output of the LDO is available on the V DD1 and V DD2 pins.
In some cases, especially on the peripheral side of the isolation,
there may not be a 5 V power supply available. The ADuM4160
has the ability to bypass the regulator and run on a 3.3 V supply
directly.
Two power pins are present on each side, V BUSx and V DDx . If 5 V
is supplied to V BUSx , an internal regulator creates 3.3 V to power
the xD+ and xD? drivers. V DDx provides external access to the
3.3 V supply to allow external bypass as well as bias for external
pull-ups. If only 3.3 V is available, it can be supplied to both
V BUSx and V DDx . This disables the regulator and powers the
coupler directly from the 3.3 V supply.
upstream side of the coupler receives power directly from the
USB bus and the downstream side is receiving 3.3 V from the
peripheral power supply. The downstream side can run from a
5 V V BUS2 power supply as well. It can be connected in the same
Figure 5. Recommended Printed Circuit Board Layout
In applications involving high common-mode transients, it
is important to minimize board coupling across the isolation
barrier. Furthermore, design the board layout such that any
coupling that does occur equally affects all pins on a given
component side. Failure to ensure this can cause voltage
differentials between pins exceeding the absolute maximum
ratings of the device, thereby leading to latch-up or permanent
damage.
DC CORRECTNESS AND MAGNETIC FIELD
IMMUNITY
Positive and negative logic transitions at the isolator input
cause narrow (~1 ns) pulses to be sent to the decoder via the
transformer. The decoder is bistable and is, therefore, either set
or reset by the pulses, indicating input logic transitions. In the
absence of logic transitions at the input for more than about
12 USB bit times, a periodic set of refresh pulses indicative of
the correct input state are sent to ensure dc correctness at the
output. If the decoder receives no internal pulses for more than
about 36 USB bit times, the input side is assumed to be unpowered
or nonfunctional, in which case the isolator output is forced to a
default state (see Table 10) by the watchdog timer circuit.
manner as V BUS1 as shown in Figure 5, if needed.
Rev. D | Page 11 of 16
相关PDF资料 |
PDF描述 |
|---|---|
| ADUM6200ARWZ | ISOLAT DGTL 5KVRMS 2CH 16SOIC-W |
| CHG-1014-001010-KCP | CONN RECEPT IDC 14POS 28-26 AWG |
| 35505-6180-A00GF | CONN SKT 2-2.3MM BLUE WIREMNT |
| ADUM6201ARWZ | ISOLAT DGTL 5KVRMS 2CH 16SOIC-W |
| ADUM3472CRSZ | ISOLAT DGTL 2.5KVRMS 4CH 20SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUM4160BRIZ-RL | 功能描述:IC USB ISOLATOR FULL/LO SPD RoHS:是 类别:隔离器 >> 数字隔离器 系列:iCoupler® 产品培训模块:IsoLoop® Isolator 标准包装:50 系列:IsoLoop® 输入 - 1 侧/2 侧:5/0 通道数:5 电源电压:3 V ~ 5.5 V 电压 - 隔离:2500Vrms 数据速率:110Mbps 传输延迟:12ns 输出类型:CMOS 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:管件 工作温度:-40°C ~ 85°C 其它名称:390-1053-5 |
| ADUM4160BRWZ | 功能描述:IC USB ISOLATOR FULL/LOW 16SOIC RoHS:是 类别:隔离器 >> 数字隔离器 系列:iCoupler® 标准包装:66 系列:iCoupler® 输入 - 1 侧/2 侧:2/2 通道数:4 电源电压:3.3V，5V 电压 - 隔离:2500Vrms 数据速率:25Mbps 传输延迟:60ns 输出类型:逻辑 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商设备封装:20-SSOP 包装:管件 工作温度:-40°C ~ 105°C |
| ADUM4160BRWZ-RL | 功能描述:ISOLATOR DGTL 5KVRMS 2CH 16-SOIC RoHS:是 类别:隔离器 >> 数字隔离器 系列:iCoupler® 产品培训模块:IsoLoop® Isolator 标准包装:50 系列:IsoLoop® 输入 - 1 侧/2 侧:5/0 通道数:5 电源电压:3 V ~ 5.5 V 电压 - 隔离:2500Vrms 数据速率:110Mbps 传输延迟:12ns 输出类型:CMOS 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:管件 工作温度:-40°C ~ 85°C 其它名称:390-1053-5 |
| ADUM4190 | 制造商:AD 制造商全称:Analog Devices 功能描述:High-stability Isolated Error Amplifier |
| ADUM4190ARIZ | 制造商:Analog Devices 功能描述:ISOLATED ERROR AMP 5KV 16SOI |
发布紧急采购，3分钟左右您将得到回复。