- 您现在的位置：买卖IC网 > Datasheet目录308 > ADUM5000ARWZ-RL (Analog Devices Inc)IC DIG ISOLATOR W/DC-DC 16SOIC Datasheet资料下载
参数资料
| 型号： | ADUM5000ARWZ-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/16页 |
| 文件大小： | 0K |
| 描述： | IC DIG ISOLATOR W/DC-DC 16SOIC |
| 设计资源： | USB Cable Isolator Circuit (CN0159) |
| 标准包装： | 1,000 |
| 系列： | IsoPower®, iCoupler® |
| 输入 - 1 侧/2 侧： | 2/0 |
| 通道数： | 2 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 电压 - 隔离： | 2500Vrms |
| 输出类型： | 逻辑 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC W |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 105°C |
Data Sheet
APPLICATIONS INFORMATION
The dc-to-dc converter section of the ADuM5000 works on
principles that are common to most switching power supplies.
It has a secondary side controller architecture with isolated pulse-
width modulation (PWM) feedback. V DD1 power is supplied to
an oscillating circuit that switches current into a chip scale air
core transformer. Power transferred to the secondary side is
rectified and regulated to either 3.3 V or 5 V. The secondary (V ISO )
side controller regulates the output by creating a PWM control
signal that is sent to the primary (V DD1 ) side by a dedicated
ADuM5000
To suppress noise and reduce ripple, a parallel combination of
at least two capacitors is required. The recommended capacitor
values are 0.1 μF and 10 μF. Best practice recommends using a
very low inductance ceramic capacitor, or its equivalent, for the
smaller value. The total lead length between both ends of the
capacitor and the input power supply pin should not exceed
10 mm. Consider bypassing between Pin 1 and Pin 8 and
between Pin 9 and Pin 16 unless both common ground pins
are connected together close to the package.
i Coupler data channel. The PWM modulates the oscillator circuit
to control the power being sent to the secondary side. Feedback
allows for significantly higher power and efficiency.
The ADuM5000 provides a regulation control output (RC OUT )
signal that can be connected to other iso Power devices. This feature
allows a single regulator to control multiple power modules without
contention. When auxiliary power modules are present, the V ISO
V DD1
GND 1
RC IN
RC OUT
RC SEL
V DD1
GND 1
NC
NC
NC
NC
V ISO
GND ISO
V SEL
V ISO
GND ISO
pins can be connected together to work as a single supply. Because
there is only one feedback control path, the supplies work together
seamlessly. The ADuM5000 can be a source of regulation control,
as well as being controlled by another iso Power device.
There is an undervoltage lockout (UVLO) with hysteresis in the
V DD1 input protection circuit. When the input voltage rises above
the UVLO threshold, the dc-to-dc converter becomes active.
The input voltage must be decreased below the turn-on threshold
by the hysteresis value to disable the converter. This feature has
many benefits in the power-up sequence of the converter, such
as ensuring that the system supply rises to a minimum level
before the ADuM5000 demands current. It also prevents any
voltage drop due to converter current from turning the supply
off and possibly oscillating.
PCB LAYOUT
The ADuM5000 digital isolator is a 0.5 W iso Power integrated
dc-to-dc converter that requires no external interface circuitry
for the logic interfaces. Power supply bypassing is required at
the input and output supply pins (see Figure 14).
The power supply section of the ADuM5000 uses a 180 MHz
oscillator frequency to pass power efficiently through its chip
scale transformers. In addition, the normal operation of the
data section of the i Coupler introduces switching transients
on the power supply pins. Bypass capacitors are required for
several operating frequencies. Noise suppression requires a low
inductance, high frequency capacitor, whereas ripple suppression
and proper regulation require a large value capacitor. These
capacitors are most conveniently connected between Pin 1 and
Pin 2 for V DD1 , and between Pin 15 and Pin 16 for V ISO .
Figure 14. Recommended PCB Layout
In applications involving high common-mode transients, ensure
that board coupling across the isolation barrier is minimized.
Furthermore, design the board layout such that any coupling that
does occur affects all pins equally on a given component side.
Failure to ensure this can cause voltage differentials between
pins exceeding the absolute maximum ratings for the device
as specified in Table 10, thereby leading to latch-up and/or
permanent damage.
The ADuM5000 is a power device that dissipates approximately
1 W of power when fully loaded. Because it is not possible to apply
a heat sink to an isolation device, the device primarily depends
on heat dissipation into the PCB through the GND pins. If the
device is used at high ambient temperatures, provide a thermal
path from the GND pins to the PCB ground plane. The board
layout in Figure 14 shows enlarged pads for Pin 2 and Pin 8
(GND 1 ) and for Pin 9 and Pin 15 (GND ISO ). Implement multiple
vias from the pad to the ground plane to significantly reduce the
temperature inside the chip. The dimensions of the expanded
pads are at the discretion of the designer and depend on the
available board space.
START-UP BEHAVIOR
The ADuM5000 does not contain a soft start circuit. Take the
start-up current and voltage behavior into account when designing
with this device.
When power is applied to V DD1 , the input switching circuit begins
to operate and draw current when the UVLO minimum voltage
is reached. The switching circuit drives the maximum available
power to the output until it reaches the regulation voltage where
PWM control begins. The amount of current and time this
takes depends on the load and the V DD1 slew rate.
Rev. B | Page 11 of 16
相关PDF资料 |
PDF描述 |
|---|---|
| ADUM5201CRWZ | IC DGTL ISOLATOR W/DC-DC 16SOIC |
| ADUM5230ARWZ-RL | IC ISOLATOR 2CH HBRIDGE 16-SOIC |
| ADUM5240ARZ-RL7 | IC ISOLATOR 2CH W/CONV 8-SOIC |
| ADUM5400CRWZ-RL | IC ISOLATOR 4CH DCDC CONV 16SOIC |
| ADUM5402WCRWZ | IC ISOLATOR 4CH DCDC CONV 16SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUM5000WARWZ | 制造商:Analog Devices 功能描述:IC DIG ISO Q100 W/DC-DC 16SOIC |
| ADUM5000WARWZ-RL | 制造商:Analog Devices 功能描述:AEC-Q100 AUTO ISOLATED DC/DC C 制造商:Analog Devices 功能描述:ISOLATED DC/DC CONVERTER - Tape and Reel 制造商:Analog Devices 功能描述:IC DIG ISO Q100 W/DC-DC 16SOIC |
| ADUM5010 | 制造商:AD 制造商全称:Analog Devices 功能描述:The ADuM50101 is an integrated, isolated dc-to-dc converter. |
| ADUM5010ARSZ | 功能描述:隔离器接口集成电路 Isolated DC/DC Conv 2.5kV RoHS:否 制造商:Texas Instruments 通道数量:2 传播延迟时间: 电源电压-最大:5.5 V 电源电压-最小:3 V 电源电流:3.6 mA 功率耗散: 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:SOIC-8 封装:Tube |
| ADUM5010ARSZ-RL7 | 功能描述:隔离器接口集成电路 Isolated DC/DC Conv 2.5kV RoHS:否 制造商:Texas Instruments 通道数量:2 传播延迟时间: 电源电压-最大:5.5 V 电源电压-最小:3 V 电源电流:3.6 mA 功率耗散: 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。