- 您现在的位置：买卖IC网 > PDF目录21371 > ADUM5401ARWZ (Analog Devices Inc)IC ISOLATOR 4CH DCDC CONV 16SOIC PDF资料下载
参数资料
| 型号： | ADUM5401ARWZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 22/28页 |
| 文件大小： | 0K |
| 描述： | IC ISOLATOR 4CH DCDC CONV 16SOIC |
| 产品培训模块： | isoPower Technology |
| 设计资源： | Fully Isolated Input Module Based on AD7793 and ADuM5401(CN0066) Fully Isolated Input Module Based on AD7793, ADuM5401, and a High Performance In-Amp (CN0067) |
| 特色产品： | ADuM540x Isolators |
| 其它图纸： | ADUM Series Quad Channel ADUM5401 Series |
| 标准包装： | 47 |
| 系列： | IsoPower®, iCoupler® |
| 输入 - 1 侧/2 侧： | 3/1 |
| 通道数： | 4 |
| 电源电压： | 3.3V，5V |
| 电压 - 隔离： | 2500Vrms |
| 数据速率： | 1Mbps |
| 传输延迟： | 55ns |
| 输出类型： | 逻辑 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC W |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 105°C |
| 产品目录页面： | 2766 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页
ADuM5401/ADuM5402/ADuM5403/ADuM5404
PROPAGATION DELAY-RELATED PARAMETERS
Propagation delay is a parameter that describes the time it takes
a logic signal to propagate through a component (see Figure 26).
The propagation delay to a logic low output may differ from the
propagation delay to a logic high.
INPUT (V Ix ) 50%
t PLH t PHL
Data Sheet
As a result, the ADuM5401 / ADuM5402 / ADuM5403 / ADuM5404
devices can draw large amounts of current at low voltage for
extended periods of time.
The output voltage of the ADuM5401 / ADuM5402 / ADuM5403 /
ADuM5404 devices exhibits V ISO overshoot during startup. If
this overshoot could potentially damage components attached
to V ISO , a voltage-limiting device such as a Zener diode can be
used to clamp the voltage. Typical behavior is shown in Figure 19
OUTPUT (V Ox )
50%
and Figure 20.
Figure 26. Propagation Delay Parameters
Pulse width distortion is the maximum difference between
these two propagation delay values and is an indication of
how accurately the input signal timing is preserved.
Channel-to-channel matching refers to the maximum amount
the propagation delay differs between channels within a single
ADuM5401 / ADuM5402 / ADuM5403 / ADuM5404 component.
Propagation delay skew refers to the maximum amount the
propagation delay differs between multiple ADuM5401 /
ADuM5402 / ADuM5403 / ADuM5404 components operating
under the same conditions.
START-UP BEHAVIOR
The ADuM5401 / ADuM5402 / ADuM5403 / ADuM5404 do not
contain a soft start circuit. Therefore, the start-up current and
voltage behavior must be taken into account when designing
with this device.
When power is applied to V DD1 , the input switching circuit begins
to operate and draw current when the UVLO minimum voltage
is reached. The switching circuit drives the maximum available
power to the output until it reaches the regulation voltage where
PWM control begins. The amount of current and the time
required to reach regulation voltage depends on the load and
the V DD1 slew rate.
With a fast V DD1 slew rate (200 μs or less), the peak current draws
up to 100 mA/V of V DD1 . The input voltage goes high faster than
the output can turn on, so the peak current is proportional to
the maximum input voltage.
With a slow V DD1 slew rate (in the millisecond range), the input
voltage is not changing quickly when V DD1 reaches the UVLO
minimum voltage. The current surge is approximately 300 mA
because V DD1 is nearly constant at the 2.7 V UVLO voltage. The
behavior during startup is similar to when the device load is a
short circuit; these values are consistent with the short-circuit
current shown in Figure 14.
When starting the device for V ISO = 5 V operation, do not limit
the current available to the V DD1 power pin to less than 300 mA.
The ADuM5401 / ADuM5402 / ADuM5403 / ADuM5404 devices
may not be able to drive the output to the regulation point if a
current-limiting device clamps the V DD1 voltage during startup.
EMI CONSIDERATIONS
The dc-to-dc converter section of the ADuM5401 / ADuM5402 /
ADuM5403 / ADuM5404 devices must operate at 180 MHz to
allow efficient power transfer through the small transformers.
This creates high frequency currents that can propagate in circuit
board ground and power planes, causing edge emissions and
dipole radiation between the primary and secondary ground
planes. Grounded enclosures are recommended for applications
that use these devices. If grounded enclosures are not possible,
follow good RF design practices in the layout of the PCB. See the
AN-0971 Application Note for board layout recommendations
DC CORRECTNESS AND MAGNETIC FIELD IMMUNITY
Positive and negative logic transitions at the isolator input cause
narrow (~1 ns) pulses to be sent to the decoder via the transformer.
The decoder is bistable and is, therefore, either set or reset by the
pulses, indicating input logic transitions. In the absence of logic
transitions at the input for more than 1 μs, a periodic set of refresh
pulses indicative of the correct input state is sent to ensure dc
correctness at the output. If the decoder receives no internal pulses
for more than approximately 5 μs, the input side is assumed to
be unpowered or nonfunctional, and the isolator output is forced to
a default low state by the watchdog timer circuit. This situation
should occur in the ADuM5401 / ADuM5402 / ADuM5403 /
ADuM5404 during power-up and power-down operations.
The limitation on the magnetic field immunity of the
ADuM5401 / ADuM5402 / ADuM5403 / ADuM5404 is set by the
condition in which induced voltage in the receiving coil of the
transformer is sufficiently large to either falsely set or reset the
decoder. The following analysis defines the conditions under
which this may occur. The 3.3 V operating condition of the
ADuM5401 / ADuM5402 / ADuM5403 / ADuM5404 is examined
because it represents the most susceptible mode of operation.
The pulses at the transformer output have an amplitude greater
than 1.0 V. The decoder has a sensing threshold at approximately
0.5 V, thus establishing a 0.5 V margin in which induced voltages
can be tolerated. The voltage induced across the receiving coil is
given by
V = ( ?dβ/dt )∑π r n2 ; n = 1, 2, … , N
where:
β is the magnetic flux density (gauss).
r n is the radius of the n th turn in the receiving coil (cm).
N is the total number of turns in the receiving coil.
Rev. C | Page 22 of 28
相关PDF资料 |
PDF描述 |
|---|---|
| 2-1879477-3 | RES 68 OHM 1500W 5% WW WIRE |
| 1418N4SSY24 | CABINET ST STEEL 24.1X37.1X72.1 |
| 6820PL-04W-B30-D00 | FAN DC AXIAL 12V 172X50.8MM |
| 3051 WG005 | HOOK UP WIRE 22AWG WHITE/GREEN |
| 2-1879477-2 | RES 56 OHM 1500W 5% WW WIRE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUM5401ARWZ1 | 制造商:AD 制造商全称:Analog Devices 功能描述:Quad-Channel Isolators with Integrated DC-to-DC Converter |
| ADUM5401ARWZ2 | 制造商:AD 制造商全称:Analog Devices 功能描述:Quad-Channel Isolators with Integrated DC-to-DC Converter |
| ADUM5401ARWZ-RL | 功能描述:IC ISOLATOR 4CH DCDC CONV 16SOIC RoHS:是 类别:隔离器 >> 数字隔离器 系列:IsoPower®, iCoupler® 产品培训模块:IsoLoop® Isolator 标准包装:50 系列:IsoLoop® 输入 - 1 侧/2 侧:5/0 通道数:5 电源电压:3 V ~ 5.5 V 电压 - 隔离:2500Vrms 数据速率:110Mbps 传输延迟:12ns 输出类型:CMOS 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:管件 工作温度:-40°C ~ 85°C 其它名称:390-1053-5 |
| ADUM5401CRWZ | 功能描述:IC ISOLATOR 4CH DCDC CONV 16SOIC RoHS:是 类别:隔离器 >> 数字隔离器 系列:IsoPower®, iCoupler® 标准包装:66 系列:iCoupler® 输入 - 1 侧/2 侧:2/2 通道数:4 电源电压:3.3V，5V 电压 - 隔离:2500Vrms 数据速率:25Mbps 传输延迟:60ns 输出类型:逻辑 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商设备封装:20-SSOP 包装:管件 工作温度:-40°C ~ 105°C |
| ADUM5401CRWZ1 | 制造商:AD 制造商全称:Analog Devices 功能描述:Quad-Channel Isolators with Integrated DC-to-DC Converter |
发布紧急采购，3分钟左右您将得到回复。