参数资料
型号: ADUM7442ARQZ
厂商: Analog Devices Inc
文件页数: 15/20页
文件大小: 0K
描述: IC ISOLATOR DGTL QUAD 16QSOP
特色产品: ADuM744x Digital Isolator
标准包装: 98
系列: iCoupler®
输入 - 1 侧/2 侧: 2/2
通道数: 4
电源电压: 3 V ~ 5.5 V
电压 - 隔离: 1000Vrms
数据速率: 1Mbps
传输延迟: 75ns
输出类型: 逻辑
封装/外壳: 16-SSOP(0.154",3.90mm 宽)
供应商设备封装: 16-QSOP
包装: 管件
工作温度: -40°C ~ 105°C
产品目录页面: 2766 (CN2011-ZH PDF)
Data Sheet
1000
100
10
ADuM7440/ADuM7441/ADuM7442
POWER CONSUMPTION
The supply current at a given channel of the ADuM744x
isolator is a function of the supply voltage, the data rate of
the channel, and the output load of the channel.
For each input channel, the supply current is given by
1
0.1
I DDI = I DDI ( Q )
I DDI = I DDI (D) × (2 f ? f r ) + I DDI ( Q )
f ≤ 0.5 f r
f > 0.5 f r
0.01
For each output channel, the supply current is given by
I DDO = I DDO ( Q ) f ≤ 0.5 f r
1k
I DDO = ( I DDO ( D ) + (0.5 × 10 ) × C L × V DDO ) × (2 f ? f r ) + I DDO ( Q )
0.001
10k 100k 1M 10M
MAGNETIC FIELD FREQUENCY (Hz)
100M
?3
f > 0.5 f r
10k
10M
100M
100k
1M
1k
Figure 18. Maximum Allowable External Magnetic Flux Density
For example, at a magnetic field frequency of 1 MHz, the
maximum allowable magnetic field of 0.5 kgauss induces a
voltage of 0.25 V at the receiving coil. This is about 50% of the
sensing threshold and does not cause a faulty output transition.
Similarly, if such an event occurred during a transmitted pulse
(and was of the worst-case polarity), it would reduce the
received pulse from >1.0 V to 0.75 V, still well above the 0.5 V
sensing threshold of the decoder.
The preceding magnetic flux density values correspond to
specific current magnitudes at given distances from the
ADuM744x transformers. Figure 19 shows these allowable
current magnitudes as a function of frequency for selected
distances. As shown, the ADuM744x is extremely immune and
can be affected only by extremely large currents operated at
high frequency very close to the component. For the 1 MHz
example noted previously, a 1.2 kA current would have to be
placed 5 mm away from the ADuM744x to affect the operation
of the component.
1000
100
10
1
0.1 DISTANCE = 5mm
DISTANCE = 100mm
DISTANCE = 1m
0.01
MAGNETIC FIELD FREQUENCY (Hz)
Figure 19. Maximum Allowable Current for Various
Current-to-ADuM744x Spacings
Note that at combinations of strong magnetic field and high
frequency, any loops formed by printed circuit board traces can
induce error voltages sufficiently large enough to trigger the
thresholds of succeeding circuitry. Care should be taken in the
layout of such traces to avoid this possibility.
where:
I DDI (D) , I DDO (D) are the input and output dynamic supply currents
per channel (mA/Mbps).
C L is the output load capacitance (pF).
V DDO is the output supply voltage (V).
f is the input logic signal frequency (MHz); it is half the input
data rate, expressed in units of Mbps.
f r is the input stage refresh rate (Mbps).
I DDI (Q) , I DDO (Q) are the specified input and output quiescent
supply currents (mA).
To calculate the total V DD1 and V DD2 supply current, the supply
currents for each input and output channel corresponding to
V DD1 and V DD2 are calculated and totaled. Figure 8 and Figure 9
show per-channel supply currents as a function of data rate for
an unloaded output condition. Figure 10 shows the per-channel
supply current as a function of data rate for a 15 pF output
condition. Figure 11 through Figure 15 show the total V DD1 and
V DD2 supply current as a function of data rate for ADuM7440/
ADuM7441/ADuM7442 channel configurations.
INSULATION LIFETIME
All insulation structures eventually break down when subjected
to voltage stress over a sufficiently long period. The rate of
insulation degradation is dependent on the characteristics of
the voltage waveform applied across the insulation. In addition
to the testing performed by the regulatory agencies, Analog
Devices carries out an extensive set of evaluations to determine
the lifetime of the insulation structure within the ADuM744x.
Analog Devices performs accelerated life testing using voltage
levels higher than the rated continuous working voltage.
Acceleration factors for several operating conditions are
determined. These factors allow calculation of the time to
failure at the actual working voltage. The values shown in
Table 18 summarize the peak voltage for 50 years of service life
for a bipolar ac operating condition and the maximum CSA
approved working voltages. In many cases, the approved
working voltage is higher than 50-year service life voltage.
Operation at these high working voltages can lead to shortened
insulation life in some cases.
Rev. C | Page 15 of 20
相关PDF资料
PDF描述
3-1437020-9 CONN SOCKET IDC 10POS GOLD
SBH31-NBPB-D25-SP-BK CONN HDR 1.27MM 50POS GOLD SMD
5-102398-4 CONN RECEPT 12POS .100 IDC GOLD
BG0702-B044-00S-00 BLOWER DC 12V 75X25 TAC
3627-6002 PROTECT HEADER STRT 24 CONTACT
相关代理商/技术参数
参数描述
ADUM7442ARQZ 制造商:Analog Devices 功能描述:IC DIGITAL ISOLATOR 50NS QSOP-16 制造商:Analog Devices 功能描述:IC, DIGITAL ISOLATOR, 50NS, QSOP-16
ADUM7442ARQZ-RL7 功能描述:IC DIGITAL ISOLATOR 4CH 16QSOP RoHS:是 类别:隔离器 >> 数字隔离器 系列:iCoupler® 产品培训模块:IsoLoop® Isolator 标准包装:50 系列:IsoLoop® 输入 - 1 侧/2 侧:5/0 通道数:5 电源电压:3 V ~ 5.5 V 电压 - 隔离:2500Vrms 数据速率:110Mbps 传输延迟:12ns 输出类型:CMOS 封装/外壳:16-SOIC(0.154",3.90mm 宽) 供应商设备封装:16-SOIC N 包装:管件 工作温度:-40°C ~ 85°C 其它名称:390-1053-5
ADUM7442CRQZ 功能描述:IC ISOLATOR DGTL QUAD 16QSOP RoHS:是 类别:隔离器 >> 数字隔离器 系列:iCoupler® 标准包装:66 系列:iCoupler® 输入 - 1 侧/2 侧:2/2 通道数:4 电源电压:3.3V,5V 电压 - 隔离:2500Vrms 数据速率:25Mbps 传输延迟:60ns 输出类型:逻辑 封装/外壳:20-SSOP(0.209",5.30mm 宽) 供应商设备封装:20-SSOP 包装:管件 工作温度:-40°C ~ 105°C
ADUM7442CRQZ 制造商:Analog Devices 功能描述:DIGITAL ISOLATOR, 4CH, 50NS, QSOP-16
ADUM7442CRQZ-RL7 功能描述:IC DIGITAL ISOLATOR 4CH 16QSOP RoHS:是 类别:隔离器 >> 数字隔离器 系列:iCoupler® 产品培训模块:IsoLoop® Isolator 标准包装:50 系列:IsoLoop® 输入 - 1 侧/2 侧:5/0 通道数:5 电源电压:3 V ~ 5.5 V 电压 - 隔离:2500Vrms 数据速率:110Mbps 传输延迟:12ns 输出类型:CMOS 封装/外壳:16-SOIC(0.154",3.90mm 宽) 供应商设备封装:16-SOIC N 包装:管件 工作温度:-40°C ~ 85°C 其它名称:390-1053-5