- 您现在的位置：买卖IC网 > PDF目录10600 > ADV7180WBCPZ-REEL (Analog Devices Inc)IC VIDEO DECODER SDTV 40LFCSP PDF资料下载
参数资料
| 型号： | ADV7180WBCPZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 50/116页 |
| 文件大小： | 0K |
| 描述： | IC VIDEO DECODER SDTV 40LFCSP |
| 标准包装： | 2,500 |
| 类型： | 视频解码器 |
| 应用： | 数码相机，手机，便携式视频 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 40-LFCSP-VQ（6x6） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页当前第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页
Data Sheet
ADV7180
Rev. I | Page 39 of 116
CAGT[1:0], Chroma Automatic Gain Timing,
Address 0x2D[7:6]
The chroma automatic gain timing register allows the user to
influence the tracking speed of the chroma automatic gain
control. This register has an effect only if the CAGC[1:0]
register is set to 10 (automatic gain).
Table 45. CAGT Function
CAGT[1:0]
Description
00
Slow (TC = 2 sec)
01
Medium (TC = 1 sec)
10
Reserved
11 (default)
Adaptive
CG[11:0], Chroma Gain, Address 0x2D[3:0],
Address 0x2E[7:0]; CMG[11:0], Chroma Manual Gain,
Address 0x2D[3:0], Address 0x2E[7:0]
Chroma gain[11:0] is a dual-function register. If written to, a
desired manual chroma gain can be programmed. This gain
becomes active if the CAGC[1:0] function is switched to manual
fixed gain. See Equation 2 for calculating a desired gain.
If read back, this register returns the current gain value.
Depending on the setting in the CAGC[1:0] bits, this is either:
The chroma manual gain value (CAGC[1:0] set to chroma
manual gain mode).
The chroma automatic gain value (CAGC[1:0] set to any of
the automatic modes).
Table 46. CG/CMG Function
CG[11:0]/CMG[11:0]
Read/Write
Description
CMG[11:0]
Write
Manual gain for chroma
path
CG[11:0]
Read
Currently active gain
Chroma_Gain
tor
brationFac
ChromaCali
CMG
decimal
]
0
:
11
[
(2)
where ChromaCalibrationFactor is a decimal value between 0
and 4095.
Calculation of the Chroma Calibration Factor
1. Apply a CVBS signal with the color bars/SMPTE bars test
pattern content directly to the measurement equipment.
2. Ensure correct termination of 75 on the measurement
equipment. Measure chroma output levels.
3. Reconnect the source to the CVBS input of the ADV7180
system that has a backend gain of 1. Repeat the
measurement of chroma levels.
4. Turn off the Chroma AGC and manually change the
Chroma Gain Control Register CMG[11:0] until the
chroma level matches that measured directly from the
source.
This value, in decimal, is the chroma calibration factor.
CKE, Color Kill Enable, Address 0x2B[6]
The color kill enable bit allows the optional color kill function
to be switched on or off.
For QAM-based video standards (PAL and NTSC) as well as
FM-based systems (SECAM), the threshold for the color kill
decision is selectable via the CKILLTHR[2:0] bits.
If color kill is enabled and the color carrier of the incoming
video signal is less than the threshold for 128 consecutive video
lines, color processing is switched off (black and white output).
To switch the color processing back on, another 128 consecutive
lines with a color burst greater than the threshold are required.
The color kill option works only for input signals with a modulated
chroma part. For component input (YPrPb), there is no color kill.
Setting CKE to 0 disables color kill.
Setting CKE to 1 (default) enables color kill.
CKILLTHR[2:0], Color Kill Threshold, Address 0x3D[6:4]
The CKILLTHR[2:0] bits allow the user to select a threshold for
the color kill function. The threshold applies only to QAM-based
(NTSC and PAL) or FM-modulated (SECAM) video standards.
To enable the color kill function, the CKE bit must be set. For
Setting 000, Setting 001, Setting 010, and Setting 011, chroma
demodulation inside the ADV7180 may not work satisfactorily
for poor input video signals.
Table 47. CKILLTHR Function
Description
CKILLTHR[2:0]
SECAM
NTSC, PAL
000
No color kill
Kill at <0.5%
001
Kill at <5%
Kill at <1.5%
010
Kill at <7%
Kill at <2.5%
011 (default)
Kill at <8%
Kill at <4%
100
Kill at <9.5%
Kill at <8.5%
101
Kill at <15%
Kill at <16%
110
Kill at <32%
111
Reserved for Analog Devices internal use only;
do not select
相关PDF资料 |
PDF描述 |
|---|---|
| VI-2WF-IW-F1 | CONVERTER MOD DC/DC 72V 100W |
| VE-B7R-MX-F4 | CONVERTER MOD DC/DC 7.5V 75W |
| ADV7180KST48Z | IC VID DECOD SDTV 10BIT 48LQFP |
| VI-2WD-IW-F4 | CONVERTER MOD DC/DC 85V 100W |
| VE-B7R-MX-F2 | CONVERTER MOD DC/DC 7.5V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADV7180WBST48Z | 制造商:Analog Devices 功能描述: |
| ADV7180WBST48Z-RL | 功能描述:视频 IC 10-bit 4x Oversampling SDTV Decoder RoHS:否 制造商:Fairchild Semiconductor 工作电源电压:5 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-28 封装:Reel |
| ADV7180WBSTZ | 功能描述:视频 IC 10-bit 4x Oversampling SDTV Decoder RoHS:否 制造商:Fairchild Semiconductor 工作电源电压:5 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-28 封装:Reel |
| ADV7180WBSTZ-REEL | 功能描述:视频 IC 10-bit 4x Oversampling SDTV Decoder RoHS:否 制造商:Fairchild Semiconductor 工作电源电压:5 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-28 封装:Reel |
| ADV7181 | 制造商:AD 制造商全称:Analog Devices 功能描述:Multiformat SDTV Video Decoder |
发布紧急采购，3分钟左右您将得到回复。