- 您现在的位置：买卖IC网 > PDF目录21456 > AEV16024 (Panasonic Electric Works)RELAY AUTOMOTIVE SPST 60A 24V PDF资料下载
参数资料
| 型号： | AEV16024 |
| 厂商： | Panasonic Electric Works |
| 文件页数： | 9/9页 |
| 文件大小： | 0K |
| 描述： | RELAY AUTOMOTIVE SPST 60A 24V |
| 其它有关文件： | Standards Chart |
| 标准包装： | 1 |
| 系列： | AEV |
| 继电器类型： | 自动 |
| 线圈类型： | 无锁存 |
| 线圈电流： | 208mA |
| 线圈电压： | 24VDC |
| 触点形式： | SPST-NO（1 A 型） |
| 触点额定值（电流）： | 60A |
| 切换电压： | 400VDC - 标称 |
| 关闭电压（最大）： | 18 VDC |
| 关闭电压（最小）： | 2 VDC |
| 安装类型： | 底座安装 |
| 端接类型： | 螺丝端子 |
| 包装： | 托盘 |
| 操作时间： | 50ms |
| 释放时间： | 30ms |
| 工作温度： | -40°C ~ 80°C |
EV (AEV)
13. Cautions for use
1) Regarding cautions for use and explanation of technical
terms, please refer to our “Automotive Relays Automation
Controls Group Catalog”.
2) Additionally the ambient temperature and condition for your
application should be considered because pick-up and drop-out
voltage will be changed.
3) If it includes ripple, the ripple factor should be less than 5%.
For coil surge absorption, please use a zener diode or varistor,
etc., so that the clamp voltage reaches 1.5 times or more (at
least 18 V for rated 12 V type) the rated operation voltage.
If only a diode is connected in parallel with the relay coil, the
contact opening velocity will become slow and suf?cient cutoff
performance cannot be guaranteed. Please avoid such usage.
Ex. 1: When using a varistor
Recommended Varistor; Maximum Energy: more than 1J
(However, please make settings using values that take into
consideration the worst case scenario.)
Varistor voltage: For 12 V DC input, Min. 18 V
Ex. 2: When using a zener diode (circuit)
12) The relay contacts are encapsulated in an inert gas
atmosphere. Care must be exercised when the relay is to be
used or stored at high ambient temperature.
13) If the power is turned off and then immediately on after
applying the rated voltage (current) continuously to the relay’s
coil and contact, the resistance of the coil will increase due to a
rise in the coil temperature.
This causes the pick-up voltage to rise, and possibly exceed the
rated pick-up voltage. In these circumstances, take measures
such as reducing the load current, limiting the duration of current
?ow, and applying a coil voltage higher than the rated operating
voltage (quick start).
14) In case using a capacitive load (C-load), please take a
countermeasure as pre-charging to the capacitive load so that
the inrush current will not surpass 60A.
The relay might have a contact welding without such
countermeasure.
15) If the relay is used for an inductive load (L load) such that
L/R > 1ms, add surge protection in parallel with the inductive
load. If this is not done, the electrical life will decrease and cut-
(1)
12V
ZD18V
off failure may occur.
16) Use the suitable wire for wire at the load side according to
the current. If the wire diameter is small, the maximum rated
Relay
Coil
D
ZD18V +
Diode voltage
Clamp voltage
contact current cannot be guaranteed.
(Ex.) Carrying current; 60A: diameter of 15mm 2 or more
17) Take care to disconnect to the power supply when wiring.
18) Do not switch the contacts without any load as the contact
resistance may become increased rapidly.
19) The relay satis?es the protection level of JIS D 0203 R2 (of
(2)
12V
waterproof). Please take any countermeasures additionally if it
should be installed in the place where higher protection level is
Relay
Coil
ZD30V
ZD30V Zener voltage
30V ? 12V=18V
Clamp voltage
required.
20) Do not use this product in such atmosphere where any kind
of organic solvent (as benzene, thinner and alcohol) and the
strong alkali (as ammonia and caustic soda) might be adhered
to this product.
21) Be careful that foreign matter and oils and fats kind don’t
4) Lifetime is speci?ed under the standard test conditions in JIS
C 5442. (temperature 15 to 35 ° C 59 to 95 ° F , humidity 25%RH to
85%RH)
Lifetime is dependent on the coil driving circuit, load type,
operation frequency and ambient conditions. Check lifetime
under the actual condition.
stick to the main terminal parts because it is likely to cause
terminal parts to give off unusual heat.
22) Do not make additional manufacturing upon the relay
housing.
23) For AC shutoff these is no contact polarity, but con?rm the
electric life using the actual load.
Especially, Contact terminals have polarity. So if the contact
terminals were connected with opposite pole, the electric life
would be shorter.
5) When applying current which includes precipitous changes or
ripple, the relay may generate buzzing sound. Therefore, please
con?rm with the actual load.
6) If the relay is used while exceeding the coil rating, contact
rating or cycle lifetime, this may result in the risk of overheating.
7) As a general rule, do not use a relay if it has been dropped.
8) Take care to avoid cross connections as they may cause
malfunctions or overheating.
9) When the screws for ?xing relay-body and for additional
terminal are tightened, it should be used within the range of
decided torque.
10) Avoid mounting the relay in strong magnetic ?elds (near a
transformer or magnet) or close to an object that radiates heat.
11) If the several relays are mounted closely or a heat-
generation object is close to the relay, take care to check the
abnormal temperature-rise and the insulation distance between
the terminals outside of the relay.
For general cautions for use, please refer to the “CAUTIONS FOR USE OF AUTOMOTIVE RELAYS”
http://industrial.panasonic.com/ac/e/
Panasonic Corporation
Automation Controls Business Unit
industrial.panasonic.com/ac/e/
ASCTB233E 201209-T
相关PDF资料 |
PDF描述 |
|---|---|
| ADUM6401ARWZ | IC ISOLATOR 4CH DCDC CONV 16SOIC |
| 71600-126LF | CONN SOCKET IDC 26POS DUAL 30AU |
| D89140-0031HK | CONN 40POS IDC SOCKET 10GOLD |
| AEV16012 | RELAY AUTOMOTIVE SPST 60A 12V |
| ADUM4401CRWZ | IC DIGITAL ISOLATOR 4CH 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AEV17012 | 功能描述:车用继电器 EV200A Automotive Relay RoHS:否 制造商:Panasonic Electric Works 触点形式:1 Form A (SPST-NO) 触点电流额定值:200 A 线圈电压:12 VDC 线圈电阻: 线圈电流: 切换电压: 安装风格:Screw 触点材料: |
| AEV17024 | 功能描述:车用继电器 EV200A Automotive Relay RoHS:否 制造商:Panasonic Electric Works 触点形式:1 Form A (SPST-NO) 触点电流额定值:200 A 线圈电压:12 VDC 线圈电阻: 线圈电流: 切换电压: 安装风格:Screw 触点材料: |
| AEV18012 | 功能描述:车用继电器 80A 12VDC SPST NO SCREW RoHS:否 制造商:Panasonic Electric Works 触点形式:1 Form A (SPST-NO) 触点电流额定值:200 A 线圈电压:12 VDC 线圈电阻: 线圈电流: 切换电压: 安装风格:Screw 触点材料: |
| AEV18012J | 制造商:Panasonic Electric Works 功能描述: |
| AEV18012W | 功能描述:车用继电器 SPST-NO 80A 12VDC 32Ohm, Relay RoHS:否 制造商:Panasonic Electric Works 触点形式:1 Form A (SPST-NO) 触点电流额定值:200 A 线圈电压:12 VDC 线圈电阻: 线圈电流: 切换电压: 安装风格:Screw 触点材料: |
发布紧急采购，3分钟左右您将得到回复。