参数资料
| 型号： | AEV804 |
| 厂商： | Panasonic Electric Works |
| 文件页数： | 8/9页 |
| 文件大小： | 0K |
| 描述： | ACCY BUSBAR FOR 60A RELAY |
| 标准包装： | 1 |
| 附件类型： | 母线 |
| 适用于相关产品： | AEP 和 AEV 系列 |
EV (AEV)
NOTES
1. Usage, transport and storage conditions
1) Temperature: –40 to +80 ° C –40 to +176 ° F
2) Humidity: 5 to 85% RH (Avoid freezing and condensation.)
The humidity range varies with the temperature. Use within the
range indicated in the graph below.
3) Atmospheric pressure: 86 to 106 kPa
Temperature and humidity range for usage, transport, and
storage
Humidity, %RH
4. Electrical life
This relay is a high-voltage direct-current switch. In its ?nal
breakdown mode, it may lose the ability to provide the proper
cut-off. Therefore, do not exceed the indicated switching
capacity and life. (Please treat the relay as a product with limited
life and replace it when necessary.)
In the event that the relay loses cut-off ability, there is a
possibility that burning may spread to surrounding parts, so
con?gure the layout so that the power is turned off within one
second.
85
Tolerance range
5. Permeation life of internal gas
(Avoid freezing
when used at
temperatures
(Avoid
condensation
when used at
This relay uses a hermetically encased contact (capsule
contact) with gas inside. The gas has a permeation life that is
lower than
0 ° C 32 ° F )
5
temperatures
higher than
0 ° C 32 ° F )
affected by the temperature inside the capsule contact (ambient
temperature + temperature rise due to ?ow of electrical current).
4) Condensation
–40
–40
0
+32
80
+176
Temperature, ° C ° F
For this reason, make sure the ambient operating temperature is
between –40 and 80 ° C –40 and +176 ° F (200A and 300A types:
Max. 85 ° C 185 ° F ), and the ambient storage temperature is
between –40 and 85 ° C –40 and +185 ° F .
Condensation forms when there is a sudden change in
temperature under high temperature and high humidity
conditions. Condensation will cause deterioration of the relay
insulation.
5) Low temperature, low humidity environments
The plastic becomes brittle if the relay is exposed to a low
6. The coils (300 A type) and contacts (all type) of the relay
are polarized, so follow the connection schematic when
connecting the coils and contacts.
Type 300 A contains a reverse surge voltage absorption circuit;
therefore a surge protector is not needed.
temperature, low humidity environment for long periods of time.
7. For the 300 A type, drive the coil with a quick startup.
2. When installing the relay, always use washers to prevent
the screws from loosening.
? Regarding the torque value for contact terminal, it is intended
that secure an electrical connection stability by getting enough
contact pressure (Axial force) of ?xing part.
Therefore, please do not use the screw (a bolt and a nut)
preventing looseness needing running torque (Prevailing torque
type and Self lock type) because enough tightening force in axial
direction may not be secured.
In addition, there is high possibility that a case of a relay may be
broken if users use the nut for EV80A and EV120A.
Because excessive torque is applied to a case of a relay before
generation of contact pressure. (Axial force).
? Regarding the torque value for the main body of a relay, please
use suitable screw on own veri?cation.
3. Condition of tightening screw
Tighten each screw within the rated range given below.
Exceeding the maximum torque may result in breakage.
Mounting is possible in either direction.
<Relay attaching portion>
? M4 screw (for 10A type): 1.8 to 2.7 N·m
? M5 screw (for 20A, 80A, 120A, 200A and 300A types): 3 to 4
N·m
<Main terminal attaching portion>
? M5 (for 80A type): 3 to 4 N·m
? M6 (for 120A and 200A types): 6 to 8 N·m
? M8 (for 300A type): 10 to 12 N·m
(Built-in one-shot pulse generator circuit)
8. After the ON signal enters the 300A type, automatic coil
current switching occurs after approximately 0.1 seconds.
Do not repeatedly turn it OFF within that 0.1 seconds
interval, as doing so may damage the relay.
9. Be careful that foreign matter and oils and fats kind don’t
stick to the main terminal parts because it is likely to cause
terminal parts to give off unusual heat.
Also, please use the following materials for connected
harnesses and bus bars.
10A type: Min. 2 mm 2 nominal cross-sectional area
20A type: Min. 3 mm 2 nominal cross-sectional area
80A type: Min. 15 mm 2 nominal cross-sectional area
120A type: Min. 38 mm 2 nominal cross-sectional area
200A type: Min. 60 mm 2 nominal cross-sectional area
300A type: Min. 100 mm 2 nominal cross-sectional area
10. As a guide, the insertion strength of the plug-in terminal
into the relay tab terminal should be 40 to 70N (10A type), 40
to 80N (20A type). Please select a plug-in terminal (?at
connection terminal) which comply with JIS C2809-1999.
10A type: for plate thickness 0.5mm and #187 tab terminal
20A type: for plate thickness 0.8mm and #250 tab terminal
11. Avoid excessive load applied to the terminal in case of
installing such as a bus bar etc., Because it might adversely
affect the opening and closing performance.
12. Use the speci?ed connector for the connector terminal
connection (80A, 120A and 300A)
Yazaki Corporation 7283 – 1020 or equivalent
ASCTB233E 201209-T
Panasonic Corporation
Automation Controls Business Unit
industrial.panasonic.com/ac/e/
相关PDF资料 |
PDF描述 |
|---|---|
| OSTYK61420030 | CONN BARRIER STRIP 20CIRC 10MM |
| MF-SM100/33-2 | FUSE RESETTABLE 1.1A 33V SMD |
| OSTYK55118030 | CONN BARRIER STRIP 18CIRC 11MM |
| TQ4-4.5V-3 | RELAY TELECOM 4PDT 1A 4.5V |
| GBFTAX-8 | TERM BARRIER 8CIRC SGL ROW .438 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| aev-connector | 制造商:Panasonic Industrial Company 功能描述:AEV Series Automotive Relay Connector |
| AEVS16012 | 功能描述:RELAY AUTO SPST-NO 60A 12V RoHS:是 类别:继电器 >> 功率，高于 2 安 系列:AEVS 其它有关文件:Standards Chart 标准包装:50 系列:DK 继电器类型:通用 线圈类型:无锁存 线圈电流:16.7mA 线圈电压:12VDC 触点形式:SPST-NO（1 A 型） 触点额定值（电流）:10A 切换电压:250VAC，125VDC - 最小值 关闭电压（最大）:8.4 VDC 关闭电压（最小）:1.2 VDC 特点:密封式 - 全部 安装类型:通孔 端接类型:PC 引脚 包装:管件 触点材料:银锡氧化物（AgSnO） 操作时间:10ms 释放时间:8ms 线圈功率:200 mW 线圈电阻:720 欧姆 工作温度:-40°C ~ 65°C 其它名称:255-1096DK1AE-12V |
| AEVS960122 | 功能描述:RELAY AUTO SPST-NO 60A 12V RoHS:是 类别:继电器 >> 功率，高于 2 安 系列:AEVS 其它有关文件:Standards Chart 标准包装:50 系列:DK 继电器类型:通用 线圈类型:无锁存 线圈电流:16.7mA 线圈电压:12VDC 触点形式:SPST-NO（1 A 型） 触点额定值（电流）:10A 切换电压:250VAC，125VDC - 最小值 关闭电压（最大）:8.4 VDC 关闭电压（最小）:1.2 VDC 特点:密封式 - 全部 安装类型:通孔 端接类型:PC 引脚 包装:管件 触点材料:银锡氧化物（AgSnO） 操作时间:10ms 释放时间:8ms 线圈功率:200 mW 线圈电阻:720 欧姆 工作温度:-40°C ~ 65°C 其它名称:255-1096DK1AE-12V |
| AEW05ABB24 | 功能描述:CONV DC-DC 30W 24VIN 5/12/12V TR RoHS:否 类别:电源 - 板载 >> DC DC Converters 系列:AEW05 产品目录绘图:V(R,7)AH Series 标准包装:25 系列:V7AH 类型:非隔离（POL） 输出数:1 电压 - 输入（最小）:3V 电压 - 输入（最大）:5.5V Voltage - Output 1:1.8V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:12A 电源（瓦） - 制造商系列:21W 电压 - 隔离:- 特点:具有远程开/关功能和 UVLO 安装类型:通孔 封装/外壳:5-SIP 模块 尺寸/尺寸:0.70" L x 0.31" W x 0.65" H（17.8mm x 7.9mm x 16.5mm） 包装:管件 工作温度:-40°C ~ 85°C 效率:87% 电源（瓦特）- 最大:21.6W 其它名称:507-1141-5 |
| AEW07X250000GM0AA1 | 制造商:WASHERS 功能描述: |
发布紧急采购，3分钟左右您将得到回复。