收藏本站
参数资料
型号： AGLN125V5-ZCSG81I
厂商： Microsemi SoC
文件页数： 8/150页
文件大小： 0K
描述： IC FPGA NANO 1KB 125K 81-CSP
标准包装： 640
系列： IGLOO nano
逻辑元件/单元数： 3072
RAM 位总计： 36864
输入/输出数： 60
门数： 125000
电源电压： 1.425 V ~ 1.575 V
安装类型： 表面贴装
工作温度： -40°C ~ 85°C
封装/外壳： 81-WFBGA，CSBGA
供应商设备封装： 81-CSP（5x5）
Revision 17
3-1
3 – Pin Descriptions
Supply Pins
GND
Ground
Ground supply voltage to the core, I/O outputs, and I/O logic.
GNDQ
Ground (quiet)
Quiet ground supply voltage to input buffers of I/O banks. Within the package, the GNDQ plane is
decoupled from the simultaneous switching noise originated from the output buffer ground domain. This
minimizes the noise transfer within the package and improves input signal integrity. GNDQ must always
be connected to GND on the board.
VCC
Core Supply Voltage
Supply voltage to the FPGA core, nominally 1.5 V for IGLOO nano V5 devices, and 1.2 V or 1.5 V for
IGLOO nano V2 devices. VCC is required for powering the JTAG state machine in addition to VJTAG.
Even when a device is in bypass mode in a JTAG chain of interconnected devices, both VCC and VJTAG
must remain powered to allow JTAG signals to pass through the device.
VCCIBx
I/O Supply Voltage
Supply voltage to the bank's I/O output buffers and I/O logic. Bx is the I/O bank number. There are up to
eight I/O banks on low power flash devices plus a dedicated VJTAG bank. Each bank can have a
separate VCCI connection. All I/Os in a bank will run off the same VCCIBx supply. VCCI can be 1.2 V,
1.5 V, 1.8 V, 2.5 V, or 3.3 V, nominal voltage. Unused I/O banks should have their corresponding VCCI
pins tied to GND.
VMVx
I/O Supply Voltage (quiet)
Quiet supply voltage to the input buffers of each I/O bank. x is the bank number. Within the package, the
VMV plane biases the input stage of the I/Os in the I/O banks. This minimizes the noise transfer within
the package and improves input signal integrity. Each bank must have at least one VMV connection, and
no VMV should be left unconnected. All I/Os in a bank run off the same VMVx supply. VMV is used to
provide a quiet supply voltage to the input buffers of each I/O bank. VMVx can be 1.2 V, 1.5 V, 1.8 V,
2.5 V, or 3.3 V, nominal voltage. Unused I/O banks should have their corresponding VMV pins tied to GND.
VMV and VCCI should be at the same voltage within a given I/O bank. Used VMV pins must be
connected to the corresponding VCCI pins of the same bank (i.e., VMV0 to VCCIB0, VMV1 to VCCIB1,
etc.).
VCCPLA/B/C/D/E/F
PLL Supply Voltage
Supply voltage to analog PLL, nominally 1.5 V or 1.2 V.
When the PLLs are not used, the Microsemi Designer place-and-route tool automatically disables the
unused PLLs to lower power consumption. The user should tie unused VCCPLx and VCOMPLx pins to
ground. Microsemi recommends tying VCCPLx to VCC and using proper filtering circuits to decouple
VCC noise from the PLLs. Refer to the PLL Power Supply Decoupling section of the "Clock Conditioning
Circuits in IGLOO and ProASIC3 Devices" chapter in the IGLOO nano FPGA Fabric User’s Guide for a
complete board solution for the PLL analog power supply and ground.
There is one VCCPLF pin on IGLOO nano devices.
VCOMPLA/B/C/D/E/F
PLL Ground
Ground to analog PLL power supplies. When the PLLs are not used, the Microsemi Designer place-and-
route tool automatically disables the unused PLLs to lower power consumption. The user should tie
unused VCCPLx and VCOMPLx pins to ground.
There is one VCOMPLF pin on IGLOO nano devices.
VJTAG
JTAG Supply Voltage
Low power flash devices have a separate bank for the dedicated JTAG pins. The JTAG pins can be run
at any voltage from 1.5 V to 3.3 V (nominal). Isolating the JTAG power supply in a separate I/O bank
gives greater flexibility in supply selection and simplifies power supply and PCB design. If the JTAG
相关PDF资料
PDF描述
AGLP030V5-CS201 IC FPGA IGLOO PLUS 30K 201-CSP
AGLP030V5-CSG201 IC FPGA IGLOO PLUS 30K 201-CSP
A3P250-1QNG132 IC FPGA 1KB FLASH 250K 132-QFN
A3P060-TQ144 IC FPGA 1KB FLASH 60K 144-TQFP
RMC50DRTS-S734 CONN EDGECARD 100PS DIP .100 SLD
相关代理商/技术参数
参数描述
AGLN125V5-ZVQ100 功能描述:IC FPGA NANO 1KB 125K 100VQFP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:IGLOO nano 标准包装:152 系列:IGLOO PLUS LAB/CLB数:- 逻辑元件/单元数:792 RAM 位总计:- 输入/输出数:120 门数:30000 电源电压:1.14 V ~ 1.575 V 安装类型:表面贴装 工作温度:-40°C ~ 85°C 封装/外壳:289-TFBGA，CSBGA 供应商设备封装:289-CSP（14x14）
AGLN125V5-ZVQ100I 功能描述:IC FPGA NANO 1KB 125K 100VQFP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:IGLOO nano 标准包装:152 系列:IGLOO PLUS LAB/CLB数:- 逻辑元件/单元数:792 RAM 位总计:- 输入/输出数:120 门数:30000 电源电压:1.14 V ~ 1.575 V 安装类型:表面贴装 工作温度:-40°C ~ 85°C 封装/外壳:289-TFBGA，CSBGA 供应商设备封装:289-CSP（14x14）
AGLN125V5-ZVQG100 功能描述:IC FPGA NANO 1KB 125K 100VQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:IGLOO nano 标准包装:152 系列:IGLOO PLUS LAB/CLB数:- 逻辑元件/单元数:792 RAM 位总计:- 输入/输出数:120 门数:30000 电源电压:1.14 V ~ 1.575 V 安装类型:表面贴装 工作温度:-40°C ~ 85°C 封装/外壳:289-TFBGA，CSBGA 供应商设备封装:289-CSP（14x14）
AGLN125V5-ZVQG100I 功能描述:IC FPGA NANO 1KB 125K 100VQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:IGLOO nano 标准包装:152 系列:IGLOO PLUS LAB/CLB数:- 逻辑元件/单元数:792 RAM 位总计:- 输入/输出数:120 门数:30000 电源电压:1.14 V ~ 1.575 V 安装类型:表面贴装 工作温度:-40°C ~ 85°C 封装/外壳:289-TFBGA，CSBGA 供应商设备封装:289-CSP（14x14）
AGLN250V2-CSG81 功能描述:IC FPGA 250K 1.2-1.5V CSP81 RoHS:是 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:IGLOO nano 标准包装:24 系列:ECP2 LAB/CLB数:1500 逻辑元件/单元数:12000 RAM 位总计:226304 输入/输出数:131 门数:- 电源电压:1.14 V ~ 1.26 V 安装类型:表面贴装 工作温度:0°C ~ 85°C 封装/外壳:208-BFQFP 供应商设备封装:208-PQFP（28x28）
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*