- 您现在的位置：买卖IC网 > PDF目录19426 > AL8807MP-13 (Diodes Inc)IC LED DRVR CONS CURR MSOP-8EP PDF资料下载
参数资料
| 型号： | AL8807MP-13 |
| 厂商： | Diodes Inc |
| 文件页数： | 11/20页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR CONS CURR MSOP-8EP |
| 标准包装： | 2,500 |
| 恒定电流： | 是 |
| 拓扑： | PWM，降压（降压） |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 通用 |
| 类型 - 次要： | 白色 LED |
| 频率： | 1MHz |
| 电源电压： | 6 V ~ 36 V |
| 输出电压： | 36V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 供应商设备封装： | 8-MSOP-EP |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 125°C |
| 其它名称： | AL8807-MP-13DIDKR AL8807-MP-13DIDKR-ND |
AL8807
Application Information (cont.)
Soft Start
The AL8807 does not have in-built soft-start action – this provides very fast turn off of the output the stage improving PWM dimming accuracy;
nonetheless, adding an external capacitor from the CTRL pin to ground will provide a soft-start delay. This is achieved by increasing the time taken
for the CTRL voltage to rise to the turn-on threshold and by slowing down the rate of rise of the control voltage at the input of the comparator.
Adding a capacitor increases the time taken for the output to reach 90% of its final value, this delay is 0.1ms/nF, but will impact on the PWM
dimming accuracy depending on the delay introduced.
Figure 33 Soft start with 22nF capacitor on CTRL pin (V IN = 30V, I LED = 667mA, 1 LED)
Reducing Output Ripple
Peak to peak ripple current in the LED(s) can be reduced, if required, by shunting a capacitor C2 across the LED(s) as shown already in the circuit
schematic.
A value of 1 μ F will reduce the supply ripple current by a factor three (approx.). Proportionally lower ripple can be achieved with higher capacitor
values. Note that the capacitor will not affect operating frequency or efficiency, but it will increase start-up delay, by reducing the rate of rise of LED
voltage. By adding this capacitor the current waveform through the LED(s) changes from a triangular ramp to a more sinusoidal version without
altering the mean current value.
Capacitor Selection
The small size of ceramic capacitors makes them ideal for AL8807 applications. X5R and X7R types are recommended because they retain their
capacitance over wider voltage and temperature ranges than other types such as Z5U.
A 2.2 μ F input capacitor is sufficient for most intended applications of AL8807; however a 4.7 μ F input capacitor is suggested for input voltages
approaching 36V.
AL8807
Document number: DS35281 Rev. 5 - 2
11 of 20
www.diodes.com
March 2013
? Diodes Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| 172-050-242R001 | CONN DB50 FEMALE WIRE WRAP TIN |
| HK100A-12/A | PWR SUP IND LOW PRO 12V 8.5A |
| RS3-4805S | CONV DC/DC 3W 36-72VIN 05VOUT |
| 189-037-413R571 | CONN DB37 MALE-FEM .625" SPACING |
| 2100LL-220-H-RC | INDUCTOR TOROID 22UH 15% HORIZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AL8807MP-7 | 功能描述:LED照明驱动器 36V High EFF Low EMI 1A Buck LED Driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| AL8807QMP-13 | 功能描述:LED 驱动器 IC 1 输出 DC DC 稳压器 降压（降压） 模拟，PWM 调光 1.3A（开关） 8-MSOP-EP 制造商:diodes incorporated 系列:汽车级，AEC-Q100 包装:剪切带（CT） 零件状态:有效 类型:DC DC 稳压器 拓扑:降压（降压） 内部开关:是 输出数:1 电压 - 供电（最低）:6V 电压 -?供电（最高）:30V 电压 - 输出:- 电流 - 输出/通道:1.3A（开关） 频率:1MHz 调光:模拟，PWM 应用:汽车级 工作温度:-40°C ~ 125°C （TJ） 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽）裸焊盘 供应商器件封装:8-MSOP-EP 标准包装:1 |
| AL8807W5-7 | 功能描述:LED显示驱动器 LED LV Int Switch RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| AL8808EV1 | 功能描述:AL8808 1, Non-Isolated Output LED Driver Evaluation Board 制造商:diodes incorporated 系列:- 零件状态:有效 电流 - 输出/通道:680mA 输出和类型:1，非隔离 电压 - 输出:- 特性:可调光 电压 - 输入:6 V ~ 30 V 所含物品:板 使用的 IC/零件:AL8808 标准包装:1 |
| AL8808EV2 | 功能描述:AL8808 1, Non-Isolated Output LED Driver Evaluation Board 制造商:diodes incorporated 系列:- 零件状态:有效 电流 - 输出/通道:680mA 输出和类型:1，非隔离 电压 - 输出:- 特性:- 电压 - 输入:12VAC，12 V ~ 20 V 所含物品:板 使用的 IC/零件:AL8808 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。