- 您现在的位置：买卖IC网 > PDF目录20973 > AL9910-5SP-13 (Diodes Inc)IC LED DRVR HIGH BRIGHT SO8EP PDF资料下载
参数资料
| 型号： | AL9910-5SP-13 |
| 厂商： | Diodes Inc |
| 文件页数： | 8/15页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR HIGH BRIGHT SO8EP |
| 标准包装： | 1 |
| 恒定电流： | 是 |
| 拓扑： | 交直流离线开关，PWM |
| 输出数： | 1 |
| 内部驱动器： | 无 |
| 类型 - 主要： | 背光，通用 |
| 类型 - 次要： | 高亮度 LED（HBLED） |
| 频率： | 25kHz ~ 300kHz |
| 电源电压： | 85 V ~ 277 VAC |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm Width）裸露焊盘 |
| 供应商设备封装： | 8-SO 裸露焊盘 |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 105°C |
| 其它名称： | AL9910-5SP-13DIDKR |
R osc + 22
AL9910/ AL9910A/ AL9910-5
Applications Information (cont.)
Setting Operating Frequency
The AL9910 is capable of operating over a 25 and 300 kHz switching frequency range. The switching frequency is programmed by connecting an
external resistor between R OSC pin and ground. The corresponding oscillator period is:
t OSC = μs with R OSC in k Ω
25
The switching frequency is the reciprocal of the oscillator period. Typical values for R OSC vary from 75k Ω to 1M Ω
When driving smaller numbers of LEDs, care should be taken to ensure that t ON > t BLANK . The simplest way to do this is to reduce/limit the
switching frequency by increasing the R OSC value. Reducing the switching frequency will also improve the efficiency.
When operating in buck mode the designer must keep in mind that the input voltage must be maintained higher than 2 times the forward voltage
drop across the LEDs. This limitation is related to the output current instability that may develop when the AL9910 operates at a duty cycle greater
than 0.5. This instability reveals itself as an oscillation of the output current at a sub-harmonic (SBO) of the switching frequency.
The best solution is to adopt the so-called constant off-time operation as shown in Figure 2. The resistor (R OSC ) is, connected to ground by
default, to set operating frequency. To force the AL9910 to enter constant OFF time mode R OSC is connected to the gate of the external MOSFET.
This will decrease the duty cycle from 50% by increasing the total period, t OFF + t ON .
V IN
V DD
LD
V IN
AL9910/A GATE
Q1
PWM_D
R OSC
GND
CS
R OSC
Figure 2. Constant Off-Time Configuration
The oscillator period equation above now defines the AL9910 off time, t OFF .
When using this mode the nominal switching frequency is chosen and from the nominal input and output voltages the off-time can be calculated:
t OFF = ? 1 ?
?
V OUT ( nom ) ? 1
V IN ( nom ) ? ? f OSC
?
?
? ?
From this the timing resistor, R OSC , can be calculated: R OSC = ( t OFF ( μs ) ? 25 ) ? 22 ( k Ω )
Inductor Selection
The non-isolated buck circuit, Figure 1, is usually selected and it has two operation modes: continuous and discontinuous conduction modes. A
buck power stage can be designed to operate in continuous mode for load current above a certain level usually 15% to 30% of full load. Usually,
the input voltage range, the output voltage and load current are defined by the power stage specification. This leaves the inductor value as the
only design parameter to maintain continuous conduction mode. The minimum value of inductor to maintain continuous conduction mode can be
determined by the following example.
The required inductor value is determined from the desired peak-to-peak LED ripple current in the inductor; typically around 30% of the nominal
LED current.
L=
( V IN ? V LEDs ) × D
( 0 . 3 × I LED ) × f OSC
Where D is duty cycle
The next step is determining the total voltage drop across the LED string. For example, when the string consists of 10 High-Brightness LEDs and
each diode has a forward voltage drop of 3.0V at its nominal current; the total LED voltage V LEDS is 30V.
AL9910/ AL9910A/ AL9910-5
Document number: DS35103 Rev. 8 - 2
8 of 15
www.diodes.com
December 2012
? Diodes Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| GLC50GG | POWER SUPPLY SWITCHER 50W TRIPLE |
| P51-15-G-UCA-MD-4.5OVP-000-000 | SENSOR 15PSI 7/16-20UNF .5-4.5V |
| P51-100-A-I-MD-20MA-000-000 | SENSOR 100PSI 7/16-20 UNF 4-20MA |
| REC3-4805SRW/H4/C/SMD-R | CONV DC/DC 3W 36-72VIN 05VOUT |
| P51-2000-A-Z-I36-4.5V-000-000 | SENSOR 2000PSI 1/4-18NPT .5-4.5V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AL9910A | 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:UNIVERSAL HIGH VOLTAGE HIGH BRIGHTNESS LED DRIVER |
| AL9910A-5S-13 | 功能描述:LED 驱动器 IC 1 输出 交直流离线开关 降压（降压），升压（升压） 模拟，PWM 调光 8-SO 制造商:diodes incorporated 系列:- 包装:剪切带（CT） 零件状态:有效 类型:交直流离线开关 拓扑:降压（降压），升压（升压） 内部开关:无 输出数:1 电压 - 供电（最低）:20V 电压 -?供电（最高）:500V 电压 - 输出:- 电流 - 输出/通道:- 频率:300kHz 调光:模拟，PWM 应用:背光，照明，标牌 工作温度:-40°C ~ 85°C（TA） 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商器件封装:8-SO 标准包装:1 |
| AL9910A-5SP-13 | 功能描述:LED 驱动器 IC 1 输出 交直流离线开关 降压（降压），升压（升压） 模拟，PWM 调光 8-SO 裸露焊盘 制造商:diodes incorporated 系列:- 包装:剪切带（CT） 零件状态:有效 类型:交直流离线开关 拓扑:降压（降压），升压（升压） 内部开关:无 输出数:1 电压 - 供电（最低）:20V 电压 -?供电（最高）:500V 电压 - 输出:- 电流 - 输出/通道:- 频率:300kHz 调光:模拟，PWM 应用:背光，照明，标牌 工作温度:-40°C ~ 105°C（TA） 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽）裸焊盘 供应商器件封装:8-SO 裸露焊盘 标准包装:1 |
| AL9910AEV1 | 功能描述:AL9910A 1, Non-Isolated Output LED Driver Evaluation Board 制造商:diodes incorporated 系列:- 零件状态:有效 电流 - 输出/通道:140mA 输出和类型:1，非隔离 电压 - 输出:51V 特性:- 电压 - 输入:100 ~ 240 VAC 所含物品:板 使用的 IC/零件:AL9910A 标准包装:1 |
| AL9910AEV2 | 功能描述:AL9910A 1, Non-Isolated Output LED Driver Evaluation Board 制造商:diodes incorporated 系列:- 零件状态:有效 电流 - 输出/通道:2.5A 输出和类型:1，非隔离 电压 - 输出:25V 特性:- 电压 - 输入:40 V ~ 80 V 所含物品:板 使用的 IC/零件:AL9910A 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。