- 您现在的位置：买卖IC网 > PDF目录5888 > ALD2701APAL (Advanced Linear Devices Inc)IC OPAMP GP R-R CMOS DUAL 8PDIP PDF资料下载
参数资料
| 型号： | ALD2701APAL |
| 厂商： | Advanced Linear Devices Inc |
| 文件页数： | 4/9页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP GP R-R CMOS DUAL 8PDIP |
| 标准包装： | 50 |
| 放大器类型： | 通用 |
| 电路数： | 2 |
| 输出类型： | 满摆幅 |
| 转换速率： | 1 V/µs |
| 增益带宽积： | 700kHz |
| 电流 - 输入偏压： | 1pA |
| 电压 - 输入偏移： | 2000µV |
| 电流 - 电源： | 240µA |
| 电流 - 输出 / 通道： | 1mA |
| 电压 - 电源，单路/双路(±)： | 2 V ~ 10 V，±1 V ~ 5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
| 其它名称： | 1014-1130 |
ALD2701A/ALD2701B
Advanced Linear Devices
4 of 9
ALD2701
TYPICAL PERFORMANCE CHARACTERISTICS
INPUT BIAS CURRENT AS A FUNCTION
OF AMBIENT TEMPERATURE
AMBIENT TEMPERATURE (°C)
1000
100
10
0.1
1.0
INPUT
BIAS
CURRENT
(pA)
100
-25
0
75
125
50
25
-50
10000
VS = ±2.5V
OPEN LOOP VOLTAGE GAIN AS A
FUNCTION OF LOAD RESISTANCE
10M
LOAD RESISTANCE ()
10K
100K
1M
1000
100
10
1
OPEN
LOOP
VOLTAGE
GAIN
(V/mV)
VS = ±2.5V
TA = 25°C
Design & Operating Notes:
1. The ALD2701A/ALD2701B/ALD2701 CMOS operational amplifier uses
a 3 gain stage architecture and an improved frequency compensation
scheme to achieve large voltage gain, high output driving capability,
and better frequency stability. In a conventional CMOS operational
amplifier design, compensation is achieved with a pole splitting
capacitor together with a nulling resistor. This method is, however,
very bias dependent and thus cannot accommodate the large range
of supply voltage operation as is required from a stand alone CMOS
operational amplifier. The ALD2701A/ALD2701B/ALD2701 is internally
compensated for unity gain stability using a novel scheme that does
not use a nulling resistor. This scheme produces a clean single pole
roll off in the gain characteristics while providing for more than 70
degrees of phase margin at the unity gain frequency.
2. The ALD2701A/ALD2701B/ALD2701 has complementary p-channel
and n-channel input differential stages connected in parallel to
accomplish rail to rail input common mode voltage range. This means
that with the ranges of common mode input voltage close to the power
supplies, one of the two differential stages is switched off internally.
To maintain compatibility with other operational amplifiers, this switching
point has been selected to be about 1.5V below the positive supply
voltage. Since offset voltage trimming on the ALD2701A/ALD2701B/
ALD2701 is made when the input voltage is symmetrical to the supply
voltages, this internal switching does not affect a large variety of
applications such as an inverting amplifier or non-inverting amplifier
with a gain larger than 2.5 (5V operation), where the common mode
voltage does not make excursions above this switching point. The
user should however, be aware that this switching does take place if
the operational amplifier is connected as a unity gain buffer, and should
make provision in his design to allow for input offset voltage variations.
3. The input bias and offset currents are essentially input protection diode
reverse bias leakage currents, and are typically less than 1pA at room
temperature. This low input bias current assures that the analog signal
from the source will not be distorted by input bias currents. Normally,
this extremely high input impedance of greater than 1012 would not
be a problem as the source impedance would limit the node impedance.
However, for applications where source impedance is very high, it may
be necessary to limit noise and hum pickup through proper shielding.
4. The output stage consists of class AB complementary output drivers,
capable of driving a low resistance load. The output voltage swing is
limited by the drain to source on-resistance of the output transistors as
determined by the bias circuitry, and the value of the load resistor.
When connected in the voltage follower configuration, the oscillation
resistant feature, combined with the rail to rail input and output feature,
makes an effective analog signal buffer for medium to high source
impedance sensors, transducers, and other circuit networks.
5. The ALD2701A/ALD2701B/ALD2701 operational amplifier has been
designed to provide full static discharge protection. Internally, the
design has been carefully implemented to minimize latch up. However,
care must be exercised when handling the device to avoid strong static
fields that may degrade a diode junction, causing increased input
leakage currents. In using the operational amplifier, the user is advised
to power up the circuit before, or simultaneously with, any input voltages
applied and to limit input voltages not to exceed 0.3V of the power
supply voltage levels.
6. The ALD2701A/ALD2701B/ALD2701, with its micropower operation,
offers numerous benefits in reduced power supply requirements, less
noise coupling and current spikes, less thermally induced drift, better
overall reliability due to lower self heating, and lower input bias current.
It requires practically no warm up time as the chip junction heats up to
only
0.2°C above ambient temperature under most operating
conditions.
COMMON MODE INPUT VOLTAGE RANGE
AS A FUNCTION OF SUPPLY VOLTAGE
SUPPLY VOLTAGE (V)
COMMON
MODE
INPUT
VOLTAGE
RANGE
(V)
±7
±6
±5
±4
±3
±2
±1
0
±1
±2
±3
±4
±5
±6
±7
TA = 25°C
SUPPLY
CURRENT
(
A)
SUPPLY CURRENT AS A FUNCTION
OF SUPPLY VOLTAGE
SUPPLY VOLTAGE (V)
800
400
600
0
200
0
±1
±2
±3
±4
±5
±6
TA = -55°C
+25°C
+70°C
+125°C
INPUTS GROUNDED
OUTPUT UNLOADED
-25°C
相关PDF资料 |
PDF描述 |
|---|---|
| TSW-135-07-S-D | CONN HEADER 70POS .100" DL GOLD |
| LT1228CN8 | IC CURRNT FEEDBCK AMP100MHZ 8DIP |
| ALD2706BSAL | IC OPAMP GP R-R CMOS DUAL 8SOIC |
| LT1013ACN8 | IC PRECISION OP-AMP DUAL 8-DIP |
| LTC6244HVHDD#TRPBF | IC OPAMP CMOS R-R DUAL 8-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ALD2701ASA | 功能描述:运算放大器 - 运放 Micropower RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| ALD2701ASAL | 功能描述:运算放大器 - 运放 2.0mV Dual CMOS RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| ALD2701B | 制造商:ALD 制造商全称:Advanced Linear Devices 功能描述:DUAL MICROPOWER RAIL-TO-RAIL CMOS OPERATIONAL AMPLIFIER |
| ALD2701BDA | 制造商:ALD 制造商全称:Advanced Linear Devices 功能描述:DUAL MICROPOWER RAIL-TO-RAIL CMOS OPERATIONAL AMPLIFIER |
| ALD2701BPA | 制造商:ALD 制造商全称:Advanced Linear Devices 功能描述:DUAL MICROPOWER RAIL-TO-RAIL CMOS OPERATIONAL AMPLIFIER |
发布紧急采购，3分钟左右您将得到回复。