- 您现在的位置：买卖IC网 > PDF目录5884 > ALD2711ASAL (Advanced Linear Devices Inc)IC OPAMP GP R-R CMOS DUAL 8SOIC PDF资料下载
参数资料
| 型号： | ALD2711ASAL |
| 厂商： | Advanced Linear Devices Inc |
| 文件页数： | 4/9页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP GP R-R CMOS DUAL 8SOIC |
| 标准包装： | 50 |
| 放大器类型： | 通用 |
| 电路数： | 2 |
| 输出类型： | 满摆幅 |
| 转换速率： | 1 V/µs |
| 增益带宽积： | 700kHz |
| 电流 - 输入偏压： | 0.01pA |
| 电压 - 输入偏移： | 250µV |
| 电流 - 电源： | 200µA |
| 电流 - 输出 / 通道： | 1mA |
| 电压 - 电源，单路/双路(±)： | 2 V ~ 10 V，±1 V ~ 5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
| 其它名称： | 1014-1146 |
ALD2711A/ALD2711B
Advanced Linear Devices
4 of 9
ALD2711
TYPICAL PERFORMANCE CHARACTERISTICS
OPEN LOOP VOLTAGE GAIN AS A
FUNCTION OF LOAD RESISTANCE
10M
LOAD RESISTANCE ()
10K
100K
1M
1000
100
10
1
OPEN
LOOP
VOLTAGE
GAIN
(V/mV)
VS = ±2.5V
TA = 25°C
COMMON MODE INPUT VOLTAGE RANGE
AS A FUNCTION OF SUPPLY VOLTAGE
SUPPLY VOLTAGE (V)
COMMON
MODE
INPUT
VOLTAGE
RANGE
(V)
±7
±6
±5
±4
±3
±2
±1
0
±1
±2
±3
±4
±5
±6
±7
TA = 25°C
Design & Operating Notes:
1. The ALD2711A/ALD2711B/ALD2711 CMOS operational amplifier
uses a 3 gain stage architecture and an improved frequency
compensation scheme to achieve large voltage gain, high output
driving capability, and better frequency stability. In a conventional
CMOS operational amplifier design, compensation is achieved with
a pole splitting capacitor together with a nulling resistor. This method
is, however, very bias dependent and thus cannot accommodate the
large range of supply voltage operation as is required from a stand
alone CMOS operational amplifier. The ALD2711A/ALD2711B/
ALD2711 is internally compensated for unity gain stability using a
novel scheme that does not use a nulling resistor. This scheme
produces a clean single pole roll off in the gain characteristics while
providing for more than 70 degrees of phase margin at the unity gain
frequency.
2. The ALD2711A/ALD2711B/ALD2711 has complementary p-channel
and n-channel input differential stages connected in parallel to
accomplish rail to rail input common mode voltage range. This means
that with the ranges of common mode input voltage close to the power
supplies, one of the two differential stages is switched off internally.
To maintain compatibility with other operational amplifiers, this
switching point has been selected to be about 1.5V below the positive
supply voltage. Since offset voltage trimming on the ALD2711A/
ALD2711B/ALD2711 is made when the input voltage is symmetrical
to the supply voltages, this internal switching does not affect a large
variety of applications such as an inverting amplifier or non-inverting
amplifier with a gain larger than 2.5 (5V operation), where the common
mode voltage does not make excursions above this switching point.
The user should however, be aware that this switching does take
place if the operational amplifier is connected as a unity gain buffer
and should make provision in his design to allow for input offset voltage
variations.
3. The input bias and offset currents are essentially input protection
diode reverse bias leakage currents, and are typically less than 1pA
at room temperature. This low input bias current assures that the
analog signal from the source will not be distorted by input bias
currents. Normally, this extremely high input impedance of greater
than 1012 would not be a problem as the source impedance would
limit the node impedance. However, for applications where source
impedance is very high, it may be necessary to limit noise and hum
pickup through proper shielding.
4. The output stage consists of class AB complementary output drivers,
capable of driving a low resistance load. The output voltage swing is
limited by the drain to source on-resistance of the output transistors
as determined by the bias circuitry, and the value of the load resistor.
When connected in the voltage follower configuration, the oscillation
resistant feature, combined with the rail to rail input and output feature,
makes an effective analog signal buffer for medium to high source
impedance sensors, transducers, and other circuit networks.
5. The ALD2711A/ALD2711B/ALD2711 operational amplifier has been
designed to provide full static discharge protection. Internally, the
design has been carefully implemented to minimize latch up. However,
care must be exercised when handling the device to avoid strong
static fields that may degrade a diode junction, causing increased
input leakage currents. In using the operational amplifier, the user is
advised to power up the circuit before, or simultaneously with, any
input voltages applied and to limit input voltages to not exceed 0.3V
of the power supply voltage levels.
6. The ALD2711A/ALD2711B/ALD2711, with its micropower operation,
offers numerous benefits in reduced power supply requirements, less
noise coupling and current spikes, less thermally induced drift, better
overall reliability due to lower self heating, and lower input bias current.
It requires practically no warm up time as the chip junction heats up
to only 0.2°C above ambient temperature under most operating
conditions.
SUPPLY
CURRENT
(
A)
SUPPLY CURRENT AS A FUNCTION
OF SUPPLY VOLTAGE
SUPPLY VOLTAGE (V)
500
300
400
0
200
0
±1
±2
±3
±4
±5
±6
TA = -55°C
+25°C
+70°C
+125°C
INPUTS GROUNDED
OUTPUT UNLOADED
-25°C
INPUT BIAS CURRENT AS A FUNCTION
OF AMBIENT TEMPERATURE
AMBIENT TEMPERATURE (°C)
100
10
1.0
0.01
0.1
INPUT
BIAS
CURRENT
(pA)
100
-25
0
75
125
50
25
-50
1000
VS = ±2.5V
相关PDF资料 |
PDF描述 |
|---|---|
| HTSW-103-07-L-S | CONN HEADER 3POS .100" T/H GOLD |
| LT1206CS8#TR | IC AMP CURR FEEDBACK 250MA 8SOIC |
| 0314006.MXP | FUSE CERAMIC 250V FAST 3AB 6A |
| 961106-6300-AR-TP | CONN HEADER VERT 6POS GOLD SMD |
| PBC29DBEN | CONN HEADER .100 DUAL R/A 58POS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ALD2711B | 制造商:ALD 制造商全称:Advanced Linear Devices 功能描述:DUAL MICROPOWER PRECISION RAIL-TO-RAIL CMOS OPERATIONAL AMPLIFIER |
| ALD2711BDA | 制造商:未知厂家 制造商全称:未知厂家 功能描述:DUAL MICROPOWER PRECISION RAIL TO RAIL CMOS OPERATIONAL AMPLIFIER |
| ALD2711BPA | 功能描述:运算放大器 - 运放 1mV Dual Low Power RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| ALD2711BPAL | 功能描述:运算放大器 - 运放 1mV Dual Low Power RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| ALD2711BSA | 制造商:ALD 制造商全称:Advanced Linear Devices 功能描述:DUAL MICROPOWER PRECISION RAIL TO RAIL CMOS OPERATIONAL AMPLIFIER |
发布紧急采购，3分钟左右您将得到回复。