- 您现在的位置：买卖IC网 > PDF目录166205 > ALD4702B (Advanced Linear Devices, Inc.) QUAD 5V RAIL-TO-RAIL PRECISION OPERATIONAL AMPLIFIER PDF资料下载
参数资料
| 型号： | ALD4702B |
| 厂商： | Advanced Linear Devices, Inc. |
| 元件分类： | 运算放大器 |
| 英文描述： | QUAD 5V RAIL-TO-RAIL PRECISION OPERATIONAL AMPLIFIER |
| 中文描述： | 四5V电压轨至轨高精度运算放大器 |
| 文件页数： | 4/6页 |
| 文件大小： | 59K |
| 代理商： | ALD4702B |
ALD4702A/ALD4702B
Advanced Linear Devices
4
ALD4702
Design & Operating Notes:
1. The ALD4702 CMOS operational amplifier uses a 3 gain stage
architecture and an improved frequency compensation scheme to
achieve large voltage gain, high output driving capability, and better
frequency stability. The ALD4702 is internally compensated for unity
gain stability using a novel scheme. This design produces a clean
single pole roll off in the gain characteristics while providing for more
than 70 degrees of phase margin at the unity gain frequency. A unity
gain buffer using the ALD4702 will typically drive 400pF of external
load capacitance without stability problems. In the inverting unity gain
configuration, it can drive up to 800pF of load capacitance. Compared
to other CMOS operational amplifiers, the ALD4702 is much more
resistant to parasitic oscillations.
2. The ALD4702 has complementary p-channel and n-channel input
differential stages connected in parallel to accomplish rail-to-rail input
common mode voltage range. With the common mode input voltage
close to the power supplies, one of the two differential stages is
switched off internally. To maintain compatibility with other opera-
tional amplifiers, this switching point has been selected to be about
1.5V above the negative supply voltage. As offset voltage trimming on
the ALD4702 is made when the input voltage is symmetrical to the
supply voltages, this internal switching does not affect a large variety
of applications such as an inverting amplifier or non-inverting amplifier
with a gain greater than 2.5 (5V operation), where the common mode
voltage does not make excursions below this switching point.
3. The input bias and offset currents are essentially input protection diode
reverse bias leakage currents, and are typically less than 1pA at
room temperature. This low input bias current assures that the
analog signal from the source will not be distorted by input bias
currents. For applications where source impedance is very high,
it may be necessary to limit noise and hum pickup through proper
shielding.
4. The output stage consists of class AB complementary output
drivers, capable of driving a low resistance load. The output
voltage swing is limited by the drain to source on-resistance of the
output transistors as determined by the bias circuitry, and the
value of the load resistor when connected. In the voltage follower
configuration, the oscillation resistant feature, combined with the
rail to rail input and output feature, makes the ALD4702 an
effective analog signal buffer for medium to high source imped-
ance sensors, transducers, and other circuit networks.
5. The ALD4702 operational amplifier has been designed with static
discharge protection. Internally, the design has been carefully
implemented to minimize latch up.
However, care must be
exercised when handling the device to avoid strong static fields.
In using the operational amplifier, the user is advised to power up
the circuit before, or simultaneously with, any input voltages
applied and to limit input voltages to not exceed 0.3V of the power
supply voltage levels. Alternatively, a 100K
or higher value
resistor at the input terminals will limit input currents to acceptable
levels while causing very small or negligible accuracy effects.
TYPICAL PERFORMANCE CHARACTERISTICS
INPUT BIAS CURRENT AS A FUNCTION
OF AMBIENT TEMPERATURE
AMBIENT TEMPERATURE (
°C)
1000
100
10
0.1
1.0
INPUT
BIAS
CURRENT
(pA)
100
-25
0
75
125
50
25
-50
VS = ± 2.5V
10000
OPEN LOOP VOLTAGE GAIN AS A FUNCTION
OF SUPPLY VOLTAGE AND TEMPERATURE
SUPPLY VOLTAGE (V)
1000
100
10
1
OPEN
LOOP
VOLTAGE
GAIN
(V/mV)
0
±2
±4
±6
RL= 10K
RL= 5K
} -55
°C
} +25
°C
} +125
°C
±8
SUPPLY CURRENT AS A FUNCTION
OF SUPPLY VOLTAGE
SUPPLY VOLTAGE (V)
SUPPLY
CURRENT
(mA)
12
10
8
6
2
4
0
±6
±5
±4
±3
±1
±2
INPUTS GROUNDED
OUTPUTS UNLOADED
TA = -55°C
-25
°C
+80
°C
+125
°C
+25
°C
COMMON MODE INPUT VOLTAGE RANGE
AS A FUNCTION OF SUPPLY VOLTAGE
SUPPLY VOLTAGE (V)
COMMON
MODE
INPUT
VOLTAGE
RANGE
(V
)
±7
±6
±5
±4
±3
±2
±1
0
±1
±2
±3
±4
±5
±6
±7
TA = 25°C
相关PDF资料 |
PDF描述 |
|---|---|
| ALD4704 | QUAD RAIL-TO-RAIL CMOS OPERATIONAL AMPLIFIER |
| ALD4704A | QUAD RAIL-TO-RAIL CMOS OPERATIONAL AMPLIFIER |
| ALD4704B | QUAD RAIL-TO-RAIL CMOS OPERATIONAL AMPLIFIER |
| ALD4706 | QUAD ULTRA MICROPOWER RAIL-TO-RAIL CMOS OPERATIONAL AMPLIFIER |
| ALD4706A | QUAD ULTRA MICROPOWER RAIL-TO-RAIL CMOS OPERATIONAL AMPLIFIER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ALD4702BDB | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Operational Amplifier |
| ALD4702BPB | 功能描述:运算放大器 - 运放 5V Precision RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| ALD4702BPBL | 功能描述:运算放大器 - 运放 2.0mV Quad Prec CMOS RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| ALD4702BSB | 功能描述:运算放大器 - 运放 5V Precision RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| ALD4702BSBL | 功能描述:运算放大器 - 运放 2.0mV Quad Prec CMOS RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。