- 您现在的位置：买卖IC网 > PDF目录10017 > ALD500RAU-20SEL (Advanced Linear Devices Inc)IC ADC 18BIT 20SOIC PDF资料下载
参数资料
| 型号： | ALD500RAU-20SEL |
| 厂商： | Advanced Linear Devices Inc |
| 文件页数： | 12/12页 |
| 文件大小： | 0K |
| 描述： | IC ADC 18BIT 20SOIC |
| 标准包装： | 36 |
| 位数： | 18 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 10mW |
| 电压电源： | 双 ± |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SOIC |
| 供应商设备封装： | 20-SOIC |
| 包装： | 管件 |
| 输入数目和类型： | * |
ALD500RAU/ALD500RA/ALD500R
Advanced Linear Devices
9
Differential Inputs (V+IN,V-IN)
The ALD500RAU/ALD500RA/ALD500R operates with
differential voltages within the input amplifier common-mode
voltage range. The amplifier common-mode range extends
from 1.5V below positive supply to 1.5V above negative
supply. Within this common-mode voltage range, common-
mode rejection is typically 95dB.
The integrator output also follows the common-mode voltage.
When large common-mode voltages with near full-scale
differential input voltages are applied, the input signal drives
the integrator output to near the supply rails where the
integrator output is near saturation. Under such conditions,
linearity of the converter may be adversely affected as the
integrator swing can be reduced. The integrator output must
not be allowed to saturate. Typically, the integrator output can
swing to within 0.9V of either supply rails without loss of
linearity.
Analog Ground
Analog Ground is V-IN during Auto Zero Phase and Reference
Voltage Deintegration Phase. If V-IN is different from analog
ground, a common-mode voltage exists at the inputs. This
common mode signal is rejected by the high common mode
rejection ratio of the converter. In most applications, V-IN is
set at a fixed known voltage (i.e., power supply ground). All
other ground connections should be connected to digital
ground in order to minimize noise at the inputs.
Differential Reference (V+REF, V-REF)
The reference voltage can be anywhere from 1V of the power
supply voltage rails of the converter. Roll-over error is caused
by the reference capacitor losing or gaining charge due to the
stray capacitance on its nodes. The difference in reference for
(+) or (-) input voltages will cause a roll-over error. This error
can be minimized by using a large reference capacitor in
comparison to the stray capacitance.
Phase Control Inputs (A, B)
The A and B logic inputs select the ALD500RAU/ALD500RA/
ALD500R operating phase. The A and B inputs are normally
driven by a microprocessor I/O port or external logic, using
CMOS logic levels. For logic control functions of A and B logic
inputs, see Table 1.
Comparator Output (COUT)
By monitoring the comparator output during the Input Signal
Integration Phase, which is a fixed signal integrate time
period, the input signal polarity can be determined by the
microcontroller controlling the conversion. The comparator
output is HIGH for positive signals and LOW for negative
signals during the Input Signal Integration Phase. The state of
the comparator should be checked by the microcontroller at
the end of the Input Signal Integration Phase, just before
transition to the Reference Voltage Deintegration Phase. For
very low level input signals noise may cause the comparator
output state to toggle between positive and negative states.
For the ALD500RAU/ALD500RA/ALD500R, this noise has
been minimized to typically within one count.
At the start of the Reference Voltage Deintegration Phase,
comparator output is set to HIGH state. During the Reference
Voltage Deintegration Phase, the microcontroller must monitor
the comparator output to make a HIGH-to-LOW transition as
the integrator output ramp crosses zero relative to analog
ground.
This transition indicates that the conversion is
complete. The microcontroller then stops and records the
pulse count. The internal comparator delay is 1
sec, typically.
The comparator output is undefined during the Auto Zero
Phase.
Figure 4. Comparator Output
ANALOG INPUT
INTEGRATE
REFERENCE
DEINTEGRATE
ZERO
CROSSING
COMPARATOR
OUTPUT
(COUT)
REFERENCE
DEINTEGRATE
ZERO
CROSSING
INTEGRATOR
OUTPUT
(VINT)
ANALOG INPUT
INTEGRATE
INTEGRATOR
OUTPUT
(VINT)
Negative Input Signal (VIN)
Positive Input Signal (VIN)
EXTERNAL INPUT
POLARITY DETECTION
COMPARATOR
OUTPUT
(COUT)
0V
EXTERNAL INPUT
POLARITY DETECTION
相关PDF资料 |
PDF描述 |
|---|---|
| AD8124ACPZ-RL | IC HS RCVR EQUALIZER 40VFQFN |
| VE-B6L-IV-F1 | CONVERTER MOD DC/DC 28V 150W |
| ALD500RA-10SEL | IC ADC 17BIT 20SOIC |
| VI-B2M-MX-B1 | CONVERTER MOD DC/DC 10V 75W |
| VE-B6K-IV-F4 | CONVERTER MOD DC/DC 40V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ALD500SC | 制造商:ALD 制造商全称:Advanced Linear Devices 功能描述:PRECISION INTEGRATING ANALOG PROCESSOR |
| ALD500SCL | 功能描述:模数转换器 - ADC 16 Bit A/D Processor RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| ALD500SWC | 制造商:ALD 制造商全称:Advanced Linear Devices 功能描述:PRECISION INTEGRATING ANALOG PROCESSOR |
| ALD500SWCL | 功能描述:模数转换器 - ADC 16 Bit A/D Processor RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| ALD514012PJ134 | 制造商:TDK-Lambda Corporation 功能描述:DC-DC LED DRIVER, 12VDC, FIVE OUTPUT 0.15A - Bulk |
发布紧急采购，3分钟左右您将得到回复。