参数资料
| 型号： | ALQ124 |
| 厂商： | Panasonic Electric Works |
| 文件页数： | 5/5页 |
| 文件大小： | 0K |
| 描述： | RELAY GEN PURPOSE SPDT 10A 24V |
| 标准包装： | 100 |
| 系列： | ALQ |
| 继电器类型： | 通用 |
| 线圈类型： | 无锁存 |
| 线圈电流： | 16.7mA |
| 线圈电压： | 24VDC |
| 触点形式： | SPDT（1 C 型） |
| 触点额定值（电流）： | 10A |
| 切换电压： | 250VAC - 最小值 |
| 关闭电压（最大）： | 18 VDC |
| 关闭电压（最小）： | 1.2 VDC |
| 特点： | 绝缘 - B 类 |
| 安装类型： | 通孔 |
| 端接类型： | PC 引脚 |
| 包装： | 管件 |
| 触点材料： | 银镍（AgNi） |
| 操作时间： | 20ms |
| 释放时间： | 20ms |
| 线圈功率： | 400 mW |
| 线圈电阻： | 1.44 千欧 |
| 工作温度： | -40°C ~ 85°C |
| 其它名称： | 255-3561 |
LQ (ALQ)
NOTES
Usage, transport and storage
conditions
1) Temperature:
–40 to +85 ° C –40 to +185 ° F
2) Humidity: 5 to 85% RH
(Avoid freezing and condensation.)
The humidity range varies with the
temperature. Use within the range
indicated in the graph below.
3) Atmospheric pressure: 86 to 106 kPa
Temperature and humidity range for
usage, transport, and storage
Humidity, %RH
85
Tolerance range
Solder and cleaning conditions
1) Please obey the following conditions
when soldering automatically.
(1) Preheating: Within 120 ° C 248 ° F
(solder surface terminal portion) and
within 120 seconds
(2) Soldering iron: 260 ° C ± 5 ° C
500 ° F ± 41 ° F (solder temperature) and
within 6 seconds (soldering time)
2) Do not use ultrasonic cleaning. This
will adversely affect relay characteristics.
When cleaning the relay, please use
alcoholic solvents.
Cautions for use
1) For precautions regarding use and
explanations of technical terminology,
please refer to our web site.
When highly frequent opening and
closing of the relay is performed with a
load that causes arcs at the contacts,
nitrogen and oxygen in the air is fused by
the arc energy and HNO 3 is formed. This
can corrode metal materials.
Three countermeasures for these are
listed here.
? Incorporate an arc-extinguishing circuit.
? Lower the operating frequency
? Lower the ambient humidity
5) This value can change due to the
switching frequency, environmental
conditions, and desired reliability level,
therefore it is recommended to check this
with the actual load.
6) Heat, smoke, and even a ?re may
(Avoid freezing
when used at
(Avoid
condensation
(panasonic-electric-works.net/ac)
occur if the relay is used in conditions
temperatures
lower than
0 ° C 32 ° F )
5
when used at
temperatures
higher than
0 ° C 32 ° F )
2) To ensure good operation, please keep
the voltage on the coil ends to ± 5% (at
20 ° C 68 ° F ) of the rated coil operation
outside of the allowable ranges for the
coil ratings, contact ratings, operating
cycle lifetime, and other speci?cations.
–40
–40
0
+32
Temperature, ° C ° F
85
+185
voltage. Also, please be aware that the
pick-up voltage and drop-out voltage may
Therefore, do not use the relay if these
ratings are exceeded.
change depending on the temperature
7) If the relay has been dropped, the
4) Condensation
Condensation forms when there is a
sudden change in temperature under
high temperature and high humidity
conditions. Condensation will cause
deterioration of the relay insulation.
5) Freezing
Condensation or other moisture may
freeze on the relay when the
temperatures is lower than 0 ° C 32 ° F . This
causes problems such as sticking of
movable parts or operational time lags.
6) Low temperature, low humidity
environments
The plastic becomes brittle if the relay is
exposed to a low temperature, low
humidity environment for long periods of
time.
and conditions of use.
3) Keep the ripple rate of the nominal coil
voltage below 5%.
4) The cycle lifetime is de?ned under the
standard test condition speci?ed in the
JIS C 5442 standard (temperature 15 to
35 ° C 59 to 95 ° F , humidity 25 to 75%).
Check this with the real device as it is
affected by coil driving circuit, load type,
activation frequency, activation phase,
ambient conditions and other factors.
Also, be especially careful of loads such
as those listed below.
(1) When used for AC load-operating and
the operating phase is synchronous.
Rocking and fusing can easily occur due
to contact shifting.
(2) Highly frequent load-operating
appearance and characteristics should
always be checked before use.
8) Incorrect wiring may cause
unexpected events or the generation of
heat or ?ames.
ASCTB92E 201206-T
Panasonic Corporation
Automation Controls Business Unit
industrial.panasonic.com/ac/e/
相关PDF资料 |
PDF描述 |
|---|---|
| 84530-102LF | MEG-ARR 200POS PLUG 6MM W/CAP |
| 77083122P | RES ARRAY 1.2K OHM 4 RES 8-SIP |
| FOD2741BSD | OPTOISOLATOR ERROR AMP 8-SMD |
| ALZ12F48W | RELAY GEN PURPOSE SPDT 16A 48V |
| 2-936321-3 | 90/SPT HYB 32P PLUG ASSY GRY |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ALQ12F48 | 功能描述:DC/DC转换器 DC-DC 1OUT 3.3V 12A 132W 8-Pin 1/4-Brick RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| ALQ12F48-L | 制造商:EMERSON-NETWORKPOWER 制造商全称:Emerson Network Power 功能描述:Delivers up to 12 A output current (6.3 A for the 8 Vo) |
| ALQ12F48N-L | 制造商:EMERSON-NETWORKPOWER 制造商全称:Emerson Network Power 功能描述:Delivers up to 12 A output current (6.3 A for the 8 Vo) |
| ALQ12K48 | 功能描述:DC/DC转换器 DC-DC 1OUT 14.4W 1.2Vout 12A 48V RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| ALQ12K48N-L | 功能描述:DC/DC转换器 18 TO 50.4 WATTS RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。