- 您现在的位置：买卖IC网 > PDF目录366380 > AM28F010-150PEB (ADVANCED MICRO DEVICES INC) 1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory PDF资料下载
参数资料
| 型号： | AM28F010-150PEB |
| 厂商： | ADVANCED MICRO DEVICES INC |
| 元件分类： | PROM |
| 英文描述： | 1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory |
| 中文描述： | 128K X 8 FLASH 12V PROM, 150 ns, PDIP32 |
| 封装： | PLASTIC, DIP-32 |
| 文件页数： | 11/35页 |
| 文件大小： | 492K |
| 代理商： | AM28F010-150PEB |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
Am28F010
11
FLASHERASE
ERASE SEQUENCE
Erase Setup
Erase Setup is the first of a two-cycle erase command.
It is a command-only operation that stages the device
for bulk chip erase. The array contents are not altered
with this command. 20h is written to the command reg-
ister in order to perform the Erase Setup operation.
Erase
The second two-cycle erase command initiates the
bulk erase operation. You must write the Erase com-
mand (20h) again to the register. The erase operation
begins with the rising edge of the WE# pulse. The
erase operation must be terminated by writing a new
command (Erase-verify) to the register.
This two step sequence of the Setup and Erase com-
mands helps to ensure that memory contents are not
accidentally erased. Also, chip erasure can only occur
when high voltage is applied to the V
PP
pin and all con-
trol pins are in their proper state. In absence of this high
voltage, memory contents cannot be altered. Refer to
AC Erase Characteristics and Waveforms for specific
timing parameters.
Note:
The Flash memory device must be fully
programmed to 00h data prior to erasure. This
equalizes the charge on all memory cells ensuring
reliable erasure.
Erase-Verify Command
The erase operation erases all bytes of the array
in parallel. After the erase operation, all bytes must be
sequentially verified. The Erase-verify operation is initi-
ated by writing A0h to the register. The byte address to
be verified must be supplied with the command. Ad-
dresses are latched on the falling edge of the WE#
pulse or CE# pulse, whichever occurs later. The rising
edge of the WE# pulse terminates the erase operation.
Margin Verify
During the Erase-verify operation, the device applies
an internally generated margin voltage to the
addressed byte. Reading FFh from the addressed byte
indicates that all bits in the byte are properly erased.
Verify Next Address
You must write the Erase-verify command with the ap-
propriate address to the register prior to verification of
each address. Each new address is latched on the fall-
ing edge of WE# or CE# pulse, whichever occurs later.
The process continues for each byte in the memory
array until a byte does not return FFh data or all the
bytes in the array are accessed and verified.
If an address is not verified to FFh data, the entire chip
is erased again (refer to Erase Setup/Erase). Erase
verification then resumes at the address that failed to
verify. Erase is complete when all bytes in the array
have been verified. The device is now ready to be pro-
grammed. At this point, the verification operation is ter-
minated by writing a valid command (e.g. Program
Setup) to the command register. Figure 1 and Table 4,
the Flasherase
electrical erase algorithm, illustrate how
commands and bus operations are combined to per-
form electrical erasure. Refer to AC Erase Characteris-
tics and Waveforms for specific timing parameters.
相关PDF资料 |
PDF描述 |
|---|---|
| AM28F010-150PI | 1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory |
| AM28F010-150PIB | 1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory |
| AM28F010-200EC | 1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory |
| AM28F010-200ECB | 1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory |
| AM28F010-200EE | 1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AM28F010-150PI | 制造商:AMD 制造商全称:Advanced Micro Devices 功能描述:1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory |
| AM28F010-150PIB | 制造商:AMD 制造商全称:Advanced Micro Devices 功能描述:1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory |
| AM28F010-170C3/BUA | 制造商:未知厂家 制造商全称:未知厂家 功能描述:x8 Flash EEPROM |
| AM28F010-170C3/BXA | 制造商:未知厂家 制造商全称:未知厂家 功能描述:x8 Flash EEPROM |
| AM28F010-200C3/BUA | 制造商:未知厂家 制造商全称:未知厂家 功能描述:x8 Flash EEPROM |
发布紧急采购，3分钟左右您将得到回复。