- 您现在的位置：买卖IC网 > PDF目录223346 > AM29BDD160GB64CKI (ADVANCED MICRO DEVICES INC) 16 Megabit (1 M x 16-bit/512 K x 32-Bit), CMOS 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/Write Flash Memory PDF资料下载
参数资料
| 型号： | AM29BDD160GB64CKI |
| 厂商： | ADVANCED MICRO DEVICES INC |
| 元件分类： | PROM |
| 英文描述： | 16 Megabit (1 M x 16-bit/512 K x 32-Bit), CMOS 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/Write Flash Memory |
| 中文描述： | 512K X 32 FLASH 2.7V PROM, 64 ns, PQFP80 |
| 封装： | PLASTIC, QFP-80 |
| 文件页数： | 3/80页 |
| 文件大小： | 3476K |
| 代理商： | AM29BDD160GB64CKI |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页
Am29BDD160G
9
PIN CONFIGURATION
LOGIC SYMBOLS
A–1
=
Least significant address bit for the 16-
bit data bus, and selects between the
high and low word. A –1 is not used for
the 32-bit mode (WORD# = VIH).
A0–A18
=
19-bit address bus for 16 Mb device.
A9 supports 12 V autoselect inputs.
DQ0–DQ31
=
32-bit data inputs/outputs/float
WORD#
=
Selects 16-bit or 32-bit mode. When
WORD# = VIH, data is output on
DQ31–DQ0. When WORD# = VIL, data
is output on DQ15–DQ0.
CE#
=
Chip Enable Input. This signal is
asynchronous relative to CLK for the
burst mode.
OE#
=
Output Enable Input. This signal is
asynchronous relative to CLK for the
burst mode.
WE#
=
Write enable. This signal is
asynchronous relative to CLK for the
burst mode.
VSS
=
Device ground
NC
=
Pin not connected internally
RY/BY#
=
Ready/Busy output and open drain.
When RY/BY# = VIH, the device is
ready to accept read operations and
commands. When RY/BY# = VOL, the
device is either executing an
embedded algorithm or the device is
executing a hardware reset operation.
CLK
=
Clock Input that can be tied to the system
or microprocessor clock provides the
fundamental timing and internal
operating frequency.
ADV#
=
Load Burst Address input. Indicates that
the valid address is present on the
address inputs.
IND#
=
End of burst indicator for finite bursts
only. IND is low when the last word in the
burst sequence is at the data outputs.
WAIT#
=
Provides data valid feedback only when
the burst length is set to continuous.
WP#
=
Write Protect input. When WP# = VOL,
the two outermost boot block sector in
the 75% bank are write protected
regardless of other sector protection
configurations.
ACC
=
Acceleration input. When taken to 12 V,
program and erase operations are
accelerated. When not used for
acceleration, ACC = VSS to VCC.
VIO (VCCQ) =
Output Buffer Power Supply (1.65 V to
2.75 V)
VCC
=
Chip Power Supply (2.5 V to 2.75 V)
RESET#
=
Hardware reset input
X16 Mode
X32 Mode
相关PDF资料 |
PDF描述 |
|---|---|
| AM29BDD160GB64CKK | 16 Megabit (1 M x 16-bit/512 K x 32-Bit), CMOS 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/Write Flash Memory |
| AM29BDD160GB65APBE | 16 Megabit (1 M x 16-bit/512 K x 32-Bit), CMOS 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/Write Flash Memory |
| AM29BDD160GB65APBI | 16 Megabit (1 M x 16-bit/512 K x 32-Bit), CMOS 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/Write Flash Memory |
| AM29BDD160GT54DKE | 16 Megabit (1 M x 16-bit/512 K x 32-Bit), CMOS 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/Write Flash Memory |
| AM29BDD160GT54DKF | 16 Megabit (1 M x 16-bit/512 K x 32-Bit), CMOS 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/Write Flash Memory |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AM29BDS128HE9VKI | 制造商:Advanced Micro Devices 功能描述:Flash Mem Parallel/Serial 1.8V 128M-Bit 8M x 16 50ns 80-Pin FBGA |
| AM29BDS643GT5KVAI | 制造商:Spansion 功能描述:FLASH PARALLEL 1.8V 64MBIT 4MX16 55NS 44FBGA - Trays |
| AM29BL802CB-65RZET | 制造商:Spansion 功能描述: |
| AM29C01WW WAF | 制造商:Advanced Micro Devices 功能描述: |
| AM29C10API | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
发布紧急采购，3分钟左右您将得到回复。