- 您现在的位置：买卖IC网 > PDF目录366430 > AM29F160DB90FI (ADVANCED MICRO DEVICES INC) 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) CMOS 5.0 Volt-only, Boot Sector Flash Memory PDF资料下载
参数资料
| 型号： | AM29F160DB90FI |
| 厂商： | ADVANCED MICRO DEVICES INC |
| 元件分类： | PROM |
| 英文描述： | 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) CMOS 5.0 Volt-only, Boot Sector Flash Memory |
| 中文描述： | 1M X 16 FLASH 5V PROM, 90 ns, PDSO48 |
| 封装： | REVERSE, MO-142DD, TSOP-48 |
| 文件页数： | 9/46页 |
| 文件大小： | 914K |
| 代理商： | AM29F160DB90FI |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
8
Am29F160D
DEVICE BUS OPERATIONS
This section describes the requirements and use of the
device bus operations, which are initiated through the
internal command register. The command register it-
self does not occupy any addressable memory loca-
tion. The register is composed of latches that store the
commands, along with the address and data informa-
tion needed to execute the command. The contents of
the register serve as inputs to the internal state ma-
chine. The state machine outputs dictate the function of
the device. The appropriate device bus operations
table lists the inputs and control levels required, and the
resulting output. The following subsections describe
each of these operations in further detail.
Table 1.
Am29F160D Device Bus Operations
Legend:
L = Logic Low = V
IL
, H = Logic High = V
IH
, V
ID
= 12.0
±
0.5 V, X = Don’t Care, A
IN
= Address In, D
IN
= Data In, D
OUT
= Data Out
Notes:
1. Addresses are A19:A0 in word mode (BYTE# = V
IH
), A19:A-1 in byte mode (BYTE# = V
IL
).
2. The sector protect and sector unprotect functions may also be implemented via programming equipment. See the “Sector
Protection/Unprotection” section.
3. The 16 Kbyte boot sector is protected when WP# = V
IL
.
4. In CMOS mode, WP# must be at V
CC
±0.5 V or left floating.
Word/Byte Configuration
The BYTE# pin controls whether the device data I/O
pins DQ15–DQ0 operate in the byte or word configura-
tion. If the BYTE# pin is set at logic ‘1’, the device is in
word configuration, DQ15–DQ0 are active and control-
led by CE# and OE#.
If the BYTE# pin is set at logic ‘0’, the device is in byte
configuration, and only data I/O pins DQ0–DQ7 are ac-
tive and controlled by CE# and OE#. The data I/O pins
DQ8–DQ14 are tri-stated, and the DQ15 pin is used as
an input for the LSB (A-1) address function.
Requirements for Reading Array Data
To read array data from the outputs, the system must
drive the CE# and OE# pins to V
IL
. CE# is the power
control and selects the device. OE# is the output control
and gates array data to the output pins. WE# should re-
main at V
IH
.
The internal state machine is set for reading array
data upon device power-up, or after a hardware reset.
This ensures that no spurious alteration of the mem-
ory content occurs during the power transition. No
command is necessary in this mode to obtain array
data. Standard microprocessor read cycles that as-
sert valid addresses on the device address inputs
produce valid data on the device data outputs. The
device remains enabled for read access until the
command register contents are altered.
See “Reading Array Data” for more information. Refer
to the AC Read Operations table for timing specifica-
Operation
Read
Write
CE#
L
L
V
CC
±
0.5 V
L
X
OE# WE#
L
H
WP#
X
(Note 3)
RESET#
H
H
V
CC
±
0.5 V
H
L
Addresses
(Note 1)
A
IN
A
IN
DQ0–
DQ7
D
OUT
D
IN
DQ8–DQ15
BYTE#
= V
IH
D
OUT
D
IN
BYTE#
= V
IL
H
L
DQ8–DQ14 = High-Z,
DQ15 = A-1
Standby
X
X
(Note 4)
X
High-Z
High-Z
High-Z
Output Disable
Reset
H
X
H
X
X
X
X
X
High-Z
High-Z
High-Z
High-Z
High-Z
High-Z
Sector Protect
(Note 2)
L
H
L
X
V
ID
Sector Address,
A6 = L, A1 = H,
A0 = L
Sector Address,
A6 = H, A1 = H,
A0 = L
D
IN
X
X
Sector Unprotect
(Note 2)
L
H
L
X
V
ID
D
IN
X
X
Temporary Sector
Unprotect
X
X
X
(Note 3)
V
ID
A
IN
D
IN
D
IN
High-Z
相关PDF资料 |
PDF描述 |
|---|---|
| AM29F160DT120 | Triple 3-Input Positive-AND Gates 14-SOIC -40 to 85 |
| AM29F160DT120EC | Triple 3-Input Positive-AND Gates 14-SOIC -40 to 85 |
| AM29F160DT120EI | Triple 3-Input Positive-AND Gates 14-SO -40 to 85 |
| AM29F160DT120FC | Triple 3-Input Positive-AND Gates 14-SO -40 to 85 |
| AM29F160DT120FI | Triple 3-Input Positive-AND Gates 14-SO -40 to 85 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AM29F160DT-120EI | 制造商:Spansion 功能描述:16M (2MX8/1MX16) 5V, BOOT BLOCK, TOP, TSOP48, IND - Trays |
| AM29F160DT-70EF\\T | 制造商:Spansion 功能描述:FLASH PARALLEL 5V 16MBIT 2MX8/1MX16 70NS 48TSOP - Tape and Reel |
| AM29F160DT-70EF\T | 制造商:Spansion 功能描述:FLASH PARALLEL 5V 16MBIT 2MX8/1MX16 70NS 48TSOP - Tape and Reel |
| AM29F160DT-70EI | 制造商:Spansion 功能描述:NOR Flash Parallel 5V 16Mbit 2M/1M x 8bit/16bit 70ns 48-Pin TSOP |
| AM29F160DT-75EF | 功能描述:闪存 16Mb 75ns 5V Parallel NOR 闪存 RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。