- 您现在的位置：买卖IC网 > PDF目录366457 > Am29LV017B-120FCB (Advanced Micro Devices, Inc.) CAT5E 350MHZ PATCH CABLE 30FT, GREEN PDF资料下载
参数资料
| 型号： | Am29LV017B-120FCB |
| 厂商： | Advanced Micro Devices, Inc. |
| 英文描述： | CAT5E 350MHZ PATCH CABLE 30FT, GREEN |
| 中文描述： | 16兆位（2米× 8位）的CMOS 3.0伏特，只有统一部门闪存 |
| 文件页数： | 23/39页 |
| 文件大小： | 510K |
| 代理商： | AM29LV017B-120FCB |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
23
Am29LV017B
P R E L IM IN A R Y
DQ5: Exceeded Timing Limits
DQ5 indicates whether the program or erase time has
exceeded a specified internal pulse count limit. Under
these conditions DQ5 produces a “1.” This is a failure
condition that indicates the program or erase cycle was
not successfully completed.
The DQ5 failure condition may appear if the system
tries to program a “1” to a location that is previously
programmed to “0.”
Only an erase operation can
change a “0” back to a “1.”
Under this condition, the
device halts the operation, and when the operation has
exceeded the timing limits, DQ5 produces a “1.”
Under both these conditions, the system must issue
the reset command to return the device to reading
array data.
DQ3: Sector Erase Timer
After writing a sector erase command sequence, the
system may read DQ3 to determine whether or not an
erase operation has begun. (The sector erase timer
does not apply to the chip erase command.) If addi-
tional sectors are selected for erasure, the entire time-
out also applies after each additional sector erase com-
mand. When the time-out is complete, DQ3 switches
from “0” to “1.” If the time between additional sector
erase commands from the system can be assumed to
be less than 50 μs, the system need not monitor DQ3.
See also the “Sector Erase Command Sequence” sec-
tion.
After the sector erase command sequence is written,
the system should read the status on DQ7 (Data# Poll-
ing) or DQ6 (Toggle Bit I) to ensure the device has ac-
cepted the command sequence, and then read DQ3. If
DQ3 is “1”, the internally controlled erase cycle has be-
gun; all further commands (other than Erase Suspend)
are ignored until the erase operation is complete. If
DQ3 is “0”, the device will accept additional sector
erase commands. To ensure the command has been
accepted, the system software should check the status
of DQ3 prior to and following each subsequent sector
erase command. If DQ3 is high on the second status
check, the last command might not have been ac-
cepted. Table 9 shows the outputs for DQ3.
Table 9.
Write Operation Status
Notes:
1.
DQ5 switches to ‘1’ when an Embedded Program or Embedded Erase operation has exceeded the maximum timing limits.
See “DQ5: Exceeded Timing Limits” for more information.
2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further details.
Operation
DQ7
(Note 2)
DQ7#
0
DQ6
Toggle
Toggle
DQ5
(Note 1)
0
0
DQ3
N/A
1
DQ2
(Note 2)
No toggle
Toggle
RY/BY#
0
0
Standard
Mode
Embedded Program Algorithm
Embedded Erase Algorithm
Reading within Erase
Suspended Sector
Reading within Non-Erase
Suspended Sector
Erase-Suspend-Program
Erase
Suspend
Mode
1
No toggle
0
N/A
Toggle
1
Data
Data
Data
Data
Data
1
DQ7#
Toggle
0
N/A
N/A
0
相关PDF资料 |
PDF描述 |
|---|---|
| AM29LV017B-120FE | GIGABASE 350 CAT5E PATCH 100 FT, NON BOOT, GREEN |
| Am29LV017B-120FEB | GIGABASE 350 CAT5E PATCH 2 FT, NON BOOT, RED |
| AM29LV017B-120FI | GIGABASE 350 CAT5E PATCH 4 FT, NON BOOT, RED |
| Am29LV017B-80RFEB | KEY REPLACEMENT A126 CODE BLACK |
| Am29LV017B-80RFIB | LM3480 100 mA, SOT-23, Quasi Low-Dropout Linear Voltage Regulator; Package: SOT-23; No of Pins: 3; Qty per Container: 1000; Container: Reel |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AM29LV017D120EC | 制造商:Advanced Micro Devices 功能描述: |
| AM29LV017D-120EC | 制造商:SCRAFT 功能描述: 制造商:SPANSION, INC. 功能描述: |
| AM29LV017D-120EI | 制造商:Advanced Micro Devices 功能描述: |
| AM29LV017D-70EC | 制造商:Advanced Micro Devices 功能描述: |
| am29lv017d-70wcc | 制造商:Advanced Micro Devices 功能描述: |
发布紧急采购，3分钟左右您将得到回复。