- 您现在的位置：买卖IC网 > PDF目录366515 > AM29LV640ML90RPCI (ADVANCED MICRO DEVICES INC) 64 Megabit (4 M x 16-Bit/8 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control PDF资料下载
参数资料
| 型号： | AM29LV640ML90RPCI |
| 厂商： | ADVANCED MICRO DEVICES INC |
| 元件分类： | PROM |
| 英文描述： | 64 Megabit (4 M x 16-Bit/8 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control |
| 中文描述： | 4M X 16 FLASH 3V PROM, 90 ns, PBGA64 |
| 封装： | 13 X 11 MM, 1 MM PITCH, BGA-64 |
| 文件页数： | 14/62页 |
| 文件大小： | 602K |
| 代理商： | AM29LV640ML90RPCI |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页
12
Am29LV640MH/L
December 14, 2005
D A T A S H E E T
at V
HH
for operations other than accelerated program-
ming, or device damage may result. In addition, no ex-
ternal pullup is necessary since the WP#/ACC pin has
internal pullup to V
CC.
Autoselect Functions
If the system writes the autoselect command se-
quence, the device enters the autoselect mode. The
system can then read autoselect codes from the inter-
nal register (which is separate from the memory array)
on DQ7–DQ0. Standard read cycle timings apply in
this mode. Refer to the
Autoselect Mode
and
Autose-
lect Command Sequence
sections for more informa-
tion.
Standby Mode
When the system is not reading or writing to the de-
vice, it can place the device in the standby mode. In
this mode, current consumption is greatly reduced,
and the outputs are placed in the high impedance
state, independent of the OE# input.
The device enters the CMOS standby mode when the
CE# and RESET# pins are both held at V
IO
± 0.3 V.
(Note that this is a more restricted voltage range than
V
IH
.) If CE# and RESET# are held at V
IH
, but not within
V
IO
± 0.3 V, the device will be in the standby mode, but
the standby current will be greater. The device re-
quires standard access time (t
CE
) for read access
when the device is in either of these standby modes,
before it is ready to read data.
If the device is deselected during erasure or program-
ming, the device draws active current until the
operation is completed.
Refer to the
DC Characteristics
table for the standby
current specification.
Automatic Sleep Mode
The automatic sleep mode minimizes Flash device en-
ergy consumption. The device automatically enables
this mode when addresses remain stable for t
ACC
+
30 ns. The automatic sleep mode is independent of
the CE#, WE#, and OE# control signals. Standard ad-
dress access timings provide new data when ad-
dresses are changed. While in sleep mode, output
data is latched and always available to the system.
Refer to the
DC Characteristics
table for the automatic
sleep mode current specification.
RESET#: Hardware Reset Pin
The RESET# pin provides a hardware method of re-
setting the device to reading array data. When the RE-
SET# pin is driven low for at least a period of t
RP
, the
device immediately terminates any operation in
progress, tristates all output pins, and ignores all
read/write commands for the duration of the RESET#
pulse. The device also resets the internal state ma-
chine to reading array data. The operation that was in-
terrupted should be reinitiated once the device is
ready to accept another command sequence, to en-
sure data integrity.
Current is reduced for the duration of the RESET#
pulse. When RESET# is held at V
SS
±0.3 V, the device
draws CMOS standby current (I
CC4
). If RESET# is held
at V
IL
but not within V
SS
±0.3 V, the standby current will
be greater.
The RESET# pin may be tied to the system reset cir-
cuitry. A system reset would thus also reset the Flash
memory, enabling the system to read the boot-up firm-
ware from the Flash memory.
Refer to the
AC Characteristics
tables for RESET# pa-
rameters and to Figure 16 for the timing diagram.
Output Disable Mode
When the OE# input is at V
IH
, output from the device is
disabled. The output pins are placed in the high
impedance state.
相关PDF资料 |
PDF描述 |
|---|---|
| AM29LV640MU100PCI | 64 Megabit (4 M x 16-Bit) MirrorBita?? 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/Oa?? Control |
| AM29LV640MU120RWHI | 64 Megabit (4 M x 16-Bit) MirrorBita?? 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/Oa?? Control |
| AM29LV640MU120WHI | 64 Megabit (4 M x 16-Bit) MirrorBita?? 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/Oa?? Control |
| AM29LV640MU25PCI | 64 Megabit (4 M x 16-Bit) MirrorBita?? 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/Oa?? Control |
| AM29LV640MU25WHI | 64 Megabit (4 M x 16-Bit) MirrorBita?? 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/Oa?? Control |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AM29LV640MU101RPCI | 制造商:Advanced Micro Devices 功能描述: |
| AM29LV640MU90NI | 制造商:Advanced Micro Devices 功能描述: |
| AM29LV640MU90RPC1 | 制造商:Advanced Micro Devices 功能描述: |
| AM29LV640MU90RPCI | 制造商:Advanced Micro Devices 功能描述: |
| AM29LV641DH120REF | 制造商:Spansion 功能描述:Flash Memory IC |
发布紧急采购，3分钟左右您将得到回复。