- 您现在的位置：买卖IC网 > PDF目录92918 > AM55-0007TR 2400 MHz - 2500 MHz RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER PDF资料下载
参数资料
| 型号： | AM55-0007TR |
| 元件分类： | 放大器 |
| 英文描述： | 2400 MHz - 2500 MHz RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER |
| 封装： | PLASTIC, SSOP-24 |
| 文件页数： | 7/7页 |
| 文件大小： | 239K |
| 代理商： | AM55-0007TR |
V 2.00
140 mW Power Amplifier with T/R Switch
AM55-0007
Port Reference
Approximate Loss (dB)
PA IN
0.25
PA OUT
0.25
Rx OUT (TO REC)
0.25
PCB DC Connector Jumper Settings
Evaluation PCB and RF Connector Losses
The DC connector on the Designer’s Kit PCB allows
selection of all the device’s operating modes. It is
accomplished by one or more of the following meth-
ods:
1. A mating female multi-pin connector (Newark
Electronics Stock # 46F-4658, not included)
2. Wires soldered to the necessary pins
(not included)
3. Clip leads (not included)
4. A combination of clip leads or wires and jumpers
(jumpers included as required)
VDD1
VDD2
ATTN
TR CTL
PA CTL
Jumper 1 (PA Sleep Control)
Position 1 = PA ON
Position 2 = PA Sleep Mode
Jumper 2 (T/R Switch Control)
Position 1 = Receive Mode
Position 2 = Transmit Mode
Jumper 3 (Attenuator Control)
Position 1 = Attenuator ON (Low Power Transmit)
Position 2 = Attenuator OFF (High Power Transmit)
In order to prevent transients which may damage
the MMIC, please adhere to the following procedure.
Turn on all power supplies and set all voltages to
0 volts BEFORE connecting the power supplies to the
DC connector.
Set jumpers for desired test mode.
Apply a -5.0 volt supply to DC connector pin 20 (VGG).
Apply a +5.0 volt supply to the DC connector pin 1 (VDD1).
Apply a +5.0 volt supply to the DC connector pin 2 (VDD2).
Apply a +5.0 volt supply to the DC connector pin 19
(VDD PA).
Adjust VGG supply to -5 volts.
Adjust all VDD supplies to +5 volts.
Hot switching of jumpers will not damage device.
To power off, reverse above procedure.
1. Set VDD1 & VDD2 & VDD PA to 0 volts.
2. Set VGG to 0 volts.
3. Disconnect bias lines from DC connector.
4. Turn off power supplies.
AM55-0007SMB Biasing Procedure
Jumper 1
Jumper 2
Jumper 3
Jumper 1
Jumper 2
Jumper 3
Pin 2
Pin 1
Jumpers
(Position 1)
Jumpers
(Position 2)
Pin 20
Pin 19
相关PDF资料 |
PDF描述 |
|---|---|
| AM55-0007 | 2400 MHz - 2500 MHz RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER |
| AM55-0015TR | 2400 MHz - 2500 MHz RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER |
| AM55-0015 | 2400 MHz - 2500 MHz RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER |
| AM55-0023RTR | 800 MHz - 2000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER |
| AM55-0023TR | 800 MHz - 2000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AM55-0016 | 制造商:MA-COM 制造商全称:M/A-COM Technology Solutions, Inc. 功能描述:Switched Low Noise Amplifier 800 - 1000 MHz |
| AM55-0016_1 | 制造商:MA-COM 制造商全称:M/A-COM Technology Solutions, Inc. 功能描述:Switched Low Noise Amplifier 800 - 1000 MHz |
| AM55-0016RTR | 制造商:MA-COM 制造商全称:M/A-COM Technology Solutions, Inc. 功能描述:Switched Low Noise Amplifier 800 - 1000 MHz |
| AM55-0016SMB | 制造商:MA-COM 制造商全称:M/A-COM Technology Solutions, Inc. 功能描述:Switched Low Noise Amplifier 800 - 1000 MHz |
| AM55-0016TR | 制造商:M/A-COM Technology Solutions 功能描述:RF AMP CHIP SGL GP 1GHZ 5V 8MSOP - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。