参数资料
型号: AMIS30623C623AG
厂商: ON Semiconductor
文件页数: 21/61页
文件大小: 0K
描述: IC MOTOR DVR MICROSTP LIN 32NQFP
标准包装: 40
应用: 步进电机驱动器
评估套件: 可供
输出数: 1
电流 - 输出: 800mA
电源电压: 6.5 V ~ 29 V
工作温度: -40°C ~ 165°C
安装类型: 表面贴装
封装/外壳: 32-VQFP 裸露焊盘
供应商设备封装: 32-NQFP(7x7)
包装: 管件
AMIS ? 30623
DriveHS
Tsw = 1024 m s
Tsw_on = 128 m s
640 m s
t
DriveLS
t
“R” ? Comp
R th
t
SWI_Cmp
120 m s
t
ESW
0
1
1
1
t
ActPos
t
Figure 13. Simplified Timing Diagram Showing the Change in States for SWI Comparator
Main Control and Register, OTP memory + ROM
Power ? up Phase
Power ? up phase of the AMIS ? 30623 will not exceed
10 ms. After this phase, the AMIS ? 30623 is in standby
mode, ready to receive LIN messages and execute the
associated commands. After power ? up, the registers and
flags are in the reset state, while some of them are being
loaded with the OTP memory content (see Table 19: RAM
Registers).
Reset
After power ? up, or after a reset occurrence (e.g. a
micro ? cut on pin V BB has made V DD to go below VddReset
level), the H ? bridges will be in high ? impedance mode, and
the registers and flags will be in a predetermined position.
This is documented in Table 19: RAM Registers and
Table 20: Flags Table.
Soft ? stop
A soft ? stop is an immediate interruption of a motion, but
with a deceleration phase. At the end of this action, the
register <TagPos> is loaded with the value contained in
register <ActPos> , see Table 19: Ram Registers). The
circuit is then ready to execute a new positioning command,
provided thermal and electrical conditions allow for it.
Sleep Mode
When entering sleep mode, the stepper ? motor can be
driven to its secure position. After which, the circuit is
completely powered down, apart from the LIN receiver,
which remains active to detect a dominant state on the bus.
In case sleep mode is entered while a motion is ongoing, a
transition will occur towards secure position as described in
Positioning and Motion Control provided < SecPos> is
enabled. Otherwise, < SoftStop> is performed.
Sleep mode can be entered in the following cases:
? The circuit receives a LIN frame with identifier 0x3C
and first data byte containing 0x00 , as required by LIN
specification rev 1.3 and <SleepEn> bit = 1. See also
Sleep in the LIN Application Command section.
? In case the >SleepEn> bit = 1 and the LIN bus remains
inactive (or is lost) during more than 25000 time slots
(1.30 s at 19.2 kbit/s), a time ? out signal switches the
circuit to sleep mode.
http://onsemi.com
21
相关PDF资料
PDF描述
RMM06DTBN-S189 CONN EDGECARD 12POS R/A .156 SLD
EEU-EB2G470 CAP ALUM 47UF 400V 20% RADIAL
1-6278875-0 C/A 50.125UM RIS MTRJ 10M1
UPM2G3R3MPD1TD CAP ALUM 3.3UF 400V 20% RADIAL
VI-J1P-EX CONVERTER MOD DC/DC 13.8V 75W
相关代理商/技术参数
参数描述
AMIS30623C623ARG 功能描述:马达/运动/点火控制器和驱动器 800mA CNTRL LIN BUS MICRO STP/STALL DET RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
AMIS30623C623BG 功能描述:马达/运动/点火控制器和驱动器 LIN STEPPER DRIVER STALL RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
AMIS30623C623BRG 功能描述:马达/运动/点火控制器和驱动器 LIN STEPPER DRIVER STALL RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
AMIS-30623PGA 制造商:ON Semiconductor 功能描述:STEPPER MOTOR CNTRLR - Rail/Tube 制造商:ON Semiconductor 功能描述:STEPPER MOTOR CNTRLR - Tape and Reel
AMIS-30623PNA 制造商:ON Semiconductor 功能描述:STEPPER MOTOR CNTRLR - Trays 制造商:ON Semiconductor 功能描述:STEPPER MOTOR CNTRLR - Tape and Reel