- 您现在的位置：买卖IC网 > PDF目录92919 > AMMC-5620-W10 6000 MHz - 20000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER PDF资料下载
参数资料
| 型号： | AMMC-5620-W10 |
| 元件分类： | 放大器 |
| 英文描述： | 6000 MHz - 20000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER |
| 封装： | 0.0555 X 0.0397 INCH, DIE, 7 PIN |
| 文件页数： | 6/8页 |
| 文件大小： | 581K |
| 代理商： | AMMC-5620-W10 |
6
Biasing and Operation
The AMMC-5620 is normally biased with a single positive
drain supply connected to the VDD bond pads shown in
Figure 19. The recommended supply voltage is 5 V, which
results in IDD = 95 mA (typical).
No ground wires are required because all ground con-
nections are made with plated through-holes to the
backside of the device.
Refer the Absolute Maximum Ratings table for allowed
DC and thermal conditions.
Assembly Techniques
The backside of the AMMC-5620 chip is RF ground. For
microstripline applications, the chip should be attached
directly to the ground plane (e.g., circuit carrier or heat-
sink) using electrically conductive epoxy [1,2].
For best performance, the topside of the MMIC should be
brought up to the same height as the circuit surrounding
it. This can be accomplished by mounting a gold plated
metal shim (same length and width as the MMIC) under
the chip, which is of the correct thickness to make the
chip and adjacent circuit coplanar.
The amount of epoxy used for chip and or shim at-
tachment should be just enough to provide a thin fillet
around the bottom perimeter of the chip or shim. The
ground plane should be free of any residue that may
jeopardize electrical or mechanical attachment.
The location of the RF bond pads is shown in Figure
20. Note that all the RF input and output ports are in a
Ground-Signal-Ground configuration.
RF connections should be kept as short as reasonable to
minimize performance degradation due to undesirable
series inductance. A single bond wire is sufficient for sig-
nal connections, however double-bonding with 0.7 mil
gold wire or the use of gold mesh is recommended for
best performance, especially near the high end of the
frequency range.
Thermosonic wedge bonding is the preferred method
for wire attachment to the bond pads. Gold mesh can
be attached using a 2 mil round tracking tool and a tool
force of approximately 22 grams with an ultrasonic pow-
er of roughly 55 dB for a duration of 76 ± 8 mS. A guided
wedge at an ultrasonic power level of 64 dB can be used
for the 0.7 mil wire. The recommended wire bond stage
temperature is 150 ± 2 ° C.
Caution should be taken to not exceed the Absolute
Maximum Rating for assembly temperature and time.
The chip is 100 m thick and should be handled with
care. This MMIC has exposed air bridges on the top
surface and should be handled by the edges or with a
custom collet (do not pick up die with vacuum on die
center.)
This MMIC is also static sensitive and ESD handling pre-
cautions should be taken.
Notes:
1. Ablebond 84-1 LM1 silver epoxy is recommended.
2. Eutectic attach is not recommended and may jeopardize reliability
of the device.
相关PDF资料 |
PDF描述 |
|---|---|
| AMMC-5620-W50 | 6000 MHz - 20000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER |
| AMMC-6120-W50 | 8000 MHz - 20000 MHz RF/MICROWAVE FREQUENCY DOUBLER |
| AMMC-6140-W10 | 10000 MHz - 20000 MHz RF/MICROWAVE FREQUENCY DOUBLER |
| AMMC-6140-W50 | 10000 MHz - 20000 MHz RF/MICROWAVE FREQUENCY DOUBLER |
| AMMC-6220-W10 | 6000 MHz - 20000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AMMC-5620-W50 | 功能描述:射频放大器 Amp GaAs MMIC RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
| AMMC-6 | 功能描述:接线端子工具和配件 END CLMP F. TERM MOD RoHS:否 制造商:Phoenix Contact 产品:Tools & Accessories 类型:End Bracket |
| AMMC-6120-W10 | 功能描述:射频放大器 Doubler MMIC 6-20GHz RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
| AMMC-6120-W50 | 功能描述:射频放大器 Doubler MMIC 6-20GHz RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
| AMMC-6140-W10 | 功能描述:射频无线杂项 Doubler MMIC 6-40GHz RoHS:否 制造商:Texas Instruments 工作频率:112 kHz to 205 kHz 电源电压-最大:3.6 V 电源电压-最小:3 V 电源电流:8 mA 最大功率耗散: 工作温度范围:- 40 C to + 110 C 封装 / 箱体:VQFN-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。