- 您现在的位置：买卖IC网 > PDF目录92919 > AMMC-6241-W10 (AGILENT TECHNOLOGIES INC) 26000 MHz - 43000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER PDF资料下载
参数资料
| 型号： | AMMC-6241-W10 |
| 厂商： | AGILENT TECHNOLOGIES INC |
| 元件分类： | 放大器 |
| 英文描述： | 26000 MHz - 43000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER |
| 封装： | 0.0748 X 0.0315 INCH, 0.004 INCH HEIGHT, DIE |
| 文件页数： | 7/8页 |
| 文件大小： | 944K |
| 代理商： | AMMC-6241-W10 |
7
Biasing and Operation
The AMMC-6241 is normally
biased with a positive supply
connected to both VD1 and VD2
bond pads through the 100pF
bypass capacitor as shown in
Figure 21. The recommended
supply voltage is 3 V. It is
important to place the bypass
capacitor as close to the die as
possible. No negative gate bias
voltage is needed for the
AMMC-6241. Input and
output matching are achieved
on-die, therefore no other
external component is required
besides one 100pF bypass
capacitor for the main supply.
The input and output are DC-
blocked with internal coupling
capacitors.
No ground wires are needed
because all ground connections
are made with plated through-
holes to the backside of the
device.
Refer the Absolute Maximum
Ratings table for allowed DC
and thermal conditions.
Assembly Techniques
The backside of the MMIC
chip is RF ground. For
microstrip applications the
chip should be attached
directly to the ground plane
(e.g. circuit carrier or
heatsink) using electrically
conductive epoxy [1]
For best performance, the
topside of the MMIC should be
brought up to the same height
as the circuit surrounding it.
This can be accomplished by
mounting a gold plate metal
shim (same length and width
as the MMIC) under the chip
which is of correct thickness
to make the chip and adjacent
circuit the same height. The
amount of epoxy used for the
chip and/or shim attachment
should be just enough to
provide a thin fillet around the
bottom perimeter of the chip
or shim. The ground plan
should be free of any residue
that may jeopardize electrical
or mechanical attachment.
The location of the RF bond
pads is shown in Figure 12.
Note that all the RF input and
output ports are in a Ground-
Signal-Ground configuration.
RF connections should be kept
as short as reasonable to
minimize performance
degradation due to undesirable
series inductance. A single
bond wire is normally
sufficient for signal
connections, however double
bonding with 0.7 mil gold wire
or use of gold mesh [2] is
recommended for best
performance, especially near
the high end of the frequency
band.
Thermosonic wedge bonding is
preferred method for wire
attachment to the bond pads.
Gold mesh can be attached
using a 2 mil round tracking
tool and a tool force of
approximately 22 grams and a
ultrasonic power of roughly 55
dB for a duration of 76 +/- 8
mS. The guided wedge at an
untrasonic power level of 64
dB can be used for 0.7 mil
wire. The recommended wire
bond stage temperature is 150
+/- 2C.
Caution should be taken to not
exceed the Absolute Maximum
Notes:
[1] Ablebond 84-1 LM1 silver epoxy is
recommended.
[2] Buckbee-Mears Corporation, St. Paul, MN,
800-262-3824
Figure 18. AMMC-6241 Simplified Schematic
RFout
RFin
VD1
VD2
相关PDF资料 |
PDF描述 |
|---|---|
| AMMC-6241-W50 | 26000 MHz - 43000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER |
| AMMC-6241 | 26000 MHz - 43000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER |
| AMMC-6420-W10 | 6000 MHz - 18000 MHz RF/MICROWAVE WIDE BAND MEDIUM POWER AMPLIFIER |
| AMMC-6420 | 6000 MHz - 18000 MHz RF/MICROWAVE WIDE BAND MEDIUM POWER AMPLIFIER |
| AMMC-6420 | 6000 MHz - 18000 MHz RF/MICROWAVE WIDE BAND MEDIUM POWER AMPLIFIER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AMMC-6241-W50 | 功能描述:射频放大器 LNA MMIC 30-41GHz RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
| AMMC-6333-W10 | 功能描述:射频放大器 LNA MMIC 17-33GHz RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
| AMMC-6333-W50 | 功能描述:射频放大器 LNA MMIC 17-33GHz RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
| AMMC-6345 | 制造商:HP 制造商全称:Agilent(Hewlett-Packard) 功能描述:20 - 45 GHz Driver Amplifier |
| AMMC-6345-W10 | 功能描述:射频放大器 Amp MMIC 20-45GHz RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。