- 您现在的位置：买卖IC网 > PDF目录378403 > AN1672D (ON SEMICONDUCTOR) The ECL Translator Guide PDF资料下载
参数资料
| 型号： | AN1672D |
| 厂商： | ON SEMICONDUCTOR |
| 英文描述： | The ECL Translator Guide |
| 中文描述： | 翻译的ECL指南 |
| 文件页数： | 4/10页 |
| 文件大小： | 64K |
| 代理商： | AN1672D |
AN1672/D
http://onsemi.com
4
Section 2: Translation from Different ECL Operating Mode Drivers to Non ECL Receivers
The following table indicates the options available for translation from different ECL operating drivers to non ECL receivers.
Table 4. Translation from Different ECL Operating Mode Drivers to Non ECL Receivers
To:
From:
TTL
V
CC
= +5 V
H350
H607
ELT21
ELT23
ELT28*
LVTTL/LVCMOS
V
CC
= 3.3 V
LVEL92 + LVELT23
or EPT21
or EPT23
or LVELT23
or EPT26
CMOS
V
DD
= 5 V
PECL
V
CC
= +5 V
PECL to TTL or PECL to LVTTL/LVCMOS
Translator and HCT or ACT
LVPECL
V
CC
= +3.3 V
ELT21
ELT23
EPT21
EPT23
LVELT23
EPT26
LVPECL to LVTTL Translator and
HCT or ACT Input
LVNECL
V
EE
= 3.3 V
NECL
V
EE
= 4.5 to 5.2 V
ELT25
EPT25*
EPT25
LVNECL/TTL Translator to HCT or
ACT Input
H125
H601
H603
H605
H680*
H681*
ELT25
EPT25*
EPT25
NECL/TTL Translator to HCT or
ACT Input
*See text segment for details
From PECL to TTL
MC10H350 as PECL to TTL
Several devices are offered for translation signals from
PECL mode drivers to 5 V supplied TTL receivers. The
MC10H350 operates over the frequency range from DC to
about 50 MHz. Although operation is possible to 80 MHz,
the output will not sustain full spec V
OH
levels rolling off
with higher frequency.
Open, floating differential inputs on a gate will force the
TTL output to default LOW. By adding a pullup resistor of
1 k to 4 k , a device’s output will directly interface with
CMOS (5 V) inputs. The device input pin “common mode
range”, V
IHCMR
min to max, is insufficient to allow
recognition of LVPECL levels. Single ended operation of
the MC10H350 will require an input signal swing of 700 mV
peaktopeak or greater.
Outputs are Enabled by Pin 9, OE, going LOW. If left
floating open, MC10H350 Pin 9 will default LOW. Worst
case skew from Output to Output within a device occurs
from Input falling edge to Output falling edge at 125
°
C at
1.4 ns. For the Input rising edge to Output rising edge, the
worst case skew is about 1 ns (at 55
°
C). Device to Device
slew is less than 800 ps skew from part to part. Output drive
will come out of saturation with 80 mA 100 mA, lowering
V
OH
levels.
MC10H607 / MC100H607 as PECL to TTL
The MC10H607 and MC100H607 are Registered PECL
to TTL translators. A standard output test condition load is
50 pF and 500 to GND. MR, Pin 19, will default LOW
when floating open, allowing operation. The input pin
“common mode” range is insufficient to allow recognition
of LVPECL levels.
ELT21/23/28 as PECL to TTL
ECL inputs for ELT21/23/28 have 50 k internal
pulldown resistors. If both ECL ELT21/23 inputs are pulled
below 1.3 V, an override circuit will force the output Q to
HIGH, Qb LOW. By adding an output pullup resistor of 1 to
4 k , a device will interface with CMOS (5 V) inputs. The
input common mode range for ELT21 / ELT23 is generally
considered to be sufficient (2.2 V) to allow recognition of
PECL HIGH levels (>4 V) allowing translation. Single
ended operation may be accomplished with a V
BB
reference
voltage placed on the nondriven differential input. If a V
BB
pin is present, then it should be bypassed when used or left
floating open when unused. A simple V
BB
supply may be
created by a resistor divider providing the proper switch
point voltage to preserve duty cycle (see AND8066). A
High Current may be created from a simple buffer gate as
shown in AND8020, Figure 22.
These ELT TTL devices typically display >2X the
required data sheet drive. For example, at V
OLmax
(0.5 V)
the required sinking drive current is 24 mA and actual drive
>>50 mA. At V
OHmin
(2.4 V), the spec sourcing drive
current is 3.0 mA and the typical device will source >>8 mA.
The unloaded V
OH
max may reach as positive as 4.0 V.
相关PDF资料 |
PDF描述 |
|---|---|
| AN1687 | A FULL-FEATURED WIRELESS INTERFACE FOR RS-232 COMMUNICATIONS |
| AN1812 | Freescale Semiconductor, Inc. |
| AN2001 | Designing Expansion Boards |
| AN211A | FIFELD EFFECT TRANSISTORS IN THEORY AND PRACTICE |
| AN2121SC | USB Controller(通用串行总线（USB）控制器) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AN1673.0 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Application Circuit to Generate Plus |
| AN1687 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:A FULL-FEATURED WIRELESS INTERFACE FOR RS-232 COMMUNICATIONS |
| AN1690.0 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Electronics Meets the Challenges of Patient Monitors |
| AN16903A | 制造商:PANASONIC 制造商全称:Panasonic Semiconductor 功能描述:IC for sound multiplex demodulation in NTSC (Japanese TV mode) |
| AN-1698 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:A Specification for EMI Hardened Operational Amplifiers |
发布紧急采购，3分钟左右您将得到回复。