- 您现在的位置：买卖IC网 > Datasheet目录310 > AOZ1977AI (Alpha & Omega Semiconductor Inc)IC LED DRVR BCKLGT 16SOIC Datasheet资料下载
参数资料
| 型号： | AOZ1977AI |
| 厂商： | Alpha & Omega Semiconductor Inc |
| 文件页数： | 4/16页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR BCKLGT 16SOIC |
| 标准包装： | 3,000 |
| 系列： | EZBoost™ |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 无 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | 高亮度 LED（HBLED） |
| 频率： | 50kHz ~ 300kHz |
| 电源电压： | 8 V ~ 30 V |
| 输出电压： | 16V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 85°C |
AOZ1977
PIN 11: DPWM
This is the driver output for the gate of the LED current
control NMOS switch. DPWM = low if PIN13: DBRT
signal is low or fault condition is triggered. DPWM = high
if PIN 13: DBRT signal is high under normal operation.
The high voltage is equal to VDD voltage. It is
recommended to add a 1 ? resistor between this pin and
the NMOS gate. The resistor value can be optimized
depending on the switching frequency and selection of
the NMOS.
PIN 12: OVP
This is the input for LED Over-Voltage Protection.
OVP monitors the LED output voltage through a resistor
divider. When the voltage at this pin is higher than 1 V,
the controller will stop switching immediately until the
PIN 14: COMP
This is for feedback loop compensation. It is the output of
the error amplifier that controls PWM logic for the boost
controller. An RC network should be used to generate the
compensation for boost feedback loop.
PIN 15: ISET
This is for full scale LED current setting. A reference
voltage between 0.5 V and 0.8 V should be applied to this
pin. The voltage can be derived from a resistor divider
from the 1.2 V reference voltage at PIN 10: VREF.
To minimize power consumption, it is recommended that
the total resistance for the divider is approximately 20 k ? .
The FB voltage will regulate to this voltage level. The full
scale LED current is derived by the FB voltage divided by
the Sense resistor.
voltage at this pin is below 0.8 V.
PIN 16: FB
PIN 13: DBRT
This is the input for digital brightness control. A PWM
logic signal is applied to this pin to vary the brightness of
the LED. The brightness of the LED is proportional to the
duty cycle of the PWM logic signal. The input signal will
control the output driver at DPWM pin. This input pin
cannot be left floating.
This is the feedback input for boost controller. This pin
should connect to a resistor that senses the LED current.
The FB voltage will be regulated to ISET voltage to
determine the desired LED current when LED current
control NMOS switch is on.
Rev. 2.1 May 2012
www.aosmd.com
Page 4 of 16
相关PDF资料 |
PDF描述 |
|---|---|
| AP-104-NT | 12V PLUG TRANSFORMER EMPTY CASE |
| AP-120 | PLUG AUTO LOCKING BLACK |
| AP-121 | PLUG AUTO LOCKING BLACK W/LED |
| AP-124 | 12V AUTO PLUG STD EURO CE |
| AP-129 | PLUG 12V AUTO EURO CE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AOZ1978 | 制造商:AOSMD 制造商全称:Alpha & Omega Semiconductors 功能描述:Dual Channel High Voltage LED Driver IC |
| AOZ1995MI | 制造商:Alpha & Omega Semiconductor 功能描述:IC DISPLAY DRIVER |
| AOZ2002PI | 功能描述:Linear Voltage Regulator IC Positive Adjustable 1 Output Adj to 0.8V 2A 8-SO Exposed Pad 制造商:alpha & omega semiconductor inc. 系列:- 包装:带卷（TR） 零件状态:有效 稳压器拓扑:正，可调式 电压 - 输出:可调至 0.8V 电流 - 输出:2A 电压 - 跌落（典型值）:0.18V @ 2A 稳压器数:1 电压 - 输入:1.3 V ~ 5.5 V 电流 - 限制（最小值）:2.2A 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商器件封装:8-SO 裸露焊盘 标准包装:3,000 |
| AOZ2003 | 制造商:AOSMD 制造商全称:Alpha & Omega Semiconductors 功能描述:3A Ultra Low Dropout Linear Regulator |
| AOZ2003PI | 制造商:Alpha & Omega Semiconductor 功能描述:IC REG LDO ADJ 3A 8SO |
发布紧急采购，3分钟左右您将得到回复。