- 您现在的位置：买卖IC网 > PDF目录17091 > AP2151WG-7 (Diodes Inc)IC PWR SW USB 1CH 0.5A SOT-25-5 PDF资料下载
参数资料
| 型号： | AP2151WG-7 |
| 厂商： | Diodes Inc |
| 文件页数： | 10/17页 |
| 文件大小： | 0K |
| 描述： | IC PWR SW USB 1CH 0.5A SOT-25-5 |
| 产品变化通告： | Copper Bond Wire Change 13/Jan/2012 |
| 标准包装： | 1 |
| 类型： | USB 开关 |
| 输出数： | 1 |
| Rds（开）： | 115 毫欧 |
| 内部开关： | 是 |
| 电流限制： | 800mA |
| 输入电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-74A，SOT-753 |
| 供应商设备封装： | SOT-25 |
| 包装： | 标准包装 |
| 产品目录页面： | 1137 (CN2011-ZH PDF) |
| 其它名称： | AP2151WGDIDKR |
AP2141/ AP2151
Application Information
Power Supply Considerations
A 0.01- μ F to 0.1- μ F X7R or X5R ceramic bypass capacitor between IN and GND, close to the device, is recommended. Placing a high-value
electrolytic capacitor on the input (10- μ F minimum) and output pin(s) is recommended when the output load is heavy. This precaution reduces
power-supply transients that may cause ringing on the input. Additionally, bypassing the output with a 0.01- μ F to 0.1- μ F ceramic capacitor improves
the immunity of the device to short-circuit transients.
Over-current and Short Circuit Protection
An internal sensing FET is employed to check for over-current conditions. Unlike current-sense resistors, sense FETs do not increase the series
resistance of the current path. When an overcurrent condition is detected, the device maintains a constant output current and reduces the output
voltage accordingly. Complete shutdown occurs only if the fault stays long enough to activate thermal limiting.
Three possible overload conditions can occur. In the first condition, the output has been shorted to GND before the device is enabled or before V IN
has been applied. The AP2141/AP2151 senses the short circuit and immediately clamps output current to a certain safe level namely I LIMIT .
In the second condition, an output short or an overload occurs while the device is enabled. At the instance the overload occurs, higher current may
flow for a very short period of time before the current limit function can react. After the current limit function has tripped (reached the over-current
trip threshold), the device switches into current limiting mode and the current is clamped at I LIMIT .
In the third condition, the load has been gradually increased beyond the recommended operating current. The current is permitted to rise until the
current-limit threshold (I TRIG ) is reached or until the thermal limit of the device is exceeded. The AP2141/AP2151 is capable of delivering current up
to the current-limit threshold without damaging the device. Once the threshold has been reached, the device switches into its current limiting mode
and is set at I LIMIT .
Note that when the output has been shorted to GND at extremely low temperature (< -30°C), a minimum 120- μ F electrolytic capacitor on the output
pin is recommended. A correct capacitor type with capacitor voltage rating and temperature characteristics must be properly chosen so that
capacitance value does not drop too low at the extremely low temperature operation.
A recommended capacitor should have temperature
P D = R DS(ON) × I
characteristics of less than 10% variation of capacitance change when operated at extremely low temp. Our recommended aluminum electrolytic
capacitor type is Panasonic FC series.
FLG Response
When an over-current or over-temperature shutdown condition is encountered, the FLG open-drain output goes active low after a nominal 7-ms
deglitch timeout. The FLG output remains low until both over-current and over-temperature conditions are removed. Connecting a heavy capacitive
load to the output of the device can cause a momentary over-current condition, which does not trigger the FLG due to the 7-ms deglitch timeout.
The AP2141/AP2151 is designed to eliminate false over-current reporting without the need of external components to remove unwanted pulses.
Power Dissipation and Junction Temperature
The low on-resistance of the internal MOSFET allows the small surface-mount packages to pass large current. Using the maximum operating
ambient temperature (T A ) and R DS(ON) , the power dissipation can be calculated by:
2
Finally, calculate the junction temperature:
T J = P D x R θ JA + T A
Where:
T A = Ambient temperature °C
R θ JA = Thermal resistance
P D = Total power dissipation
AP2141/ AP2151
Document number: DS31562 Rev. 7 - 2
10 of 17
March 2013
? Diodes Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| SDR-Z | SCOTCH CODE REFILL Z |
| GSM08DRTI-S13 | CONN EDGECARD 16POS .156 EXTEND |
| ELJ-PE22NKF | INDUCTOR 22NH 10% 0603 SMD |
| SDR-Y | SCOTCH CODE REFILL Y |
| ADS7864M-EVM | EVAL MODULE FOR ADS7864M |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AP2152 | 制造商:AKM 制造商全称:AKM 功能描述:3CH High Power WLED Driver |
| AP2152A | 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:0.5A DUAL CHANNEL CURRENT-LIMITED POWER SWITCH WITH OUTPUT DISCHARGE |
| AP2152AFGEG-7 | 功能描述:电源开关 IC - USB DUAL SWITCH 125mOhms 0.5A RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube |
| AP2152AMPG-13 | 功能描述:电源开关 IC - USB DUAL SWITCH 125mOhms 0.5A RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube |
| AP2152ASG-13 | 功能描述:电源开关 IC - USB DUAL SWITCH 130mOhms 0.5A RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。