- 您现在的位置：买卖IC网 > PDF目录17092 > AP2280-2WG-7 (Diodes Inc)IC LOAD SW PROGR SOT-25 PDF资料下载
参数资料
| 型号： | AP2280-2WG-7 |
| 厂商： | Diodes Inc |
| 文件页数： | 8/12页 |
| 文件大小： | 0K |
| 描述： | IC LOAD SW PROGR SOT-25 |
| 标准包装： | 1 |
| 类型： | 高端开关 |
| 输出数： | 1 |
| Rds（开）： | 105 毫欧 |
| 内部开关： | 是 |
| 电流限制： | 2.0A |
| 输入电压： | 1.5 V ~ 6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-74A，SOT-753 |
| 供应商设备封装： | SOT-25 |
| 包装： | 标准包装 |
| 产品目录页面： | 1137 (CN2011-ZH PDF) |
| 其它名称： | AP2280-2WGDIDKR |
AP2280
Single Channel Slew Rate Controlled Load Switch
Application Note
Input Capacitor
A 1 μ F capacitor is recommended to connect
between IN and GND pins to decouple input power
supply glitch and noise. The input capacitor has no
specific type or ESR (Equivalent Series Resistance)
requirement. However, for higher current
application, ceramic capacitors are recommended
Power Dissipation
The device power dissipation and proper sizing of
the thermal plane is critical to avoid thermal
shutdown and ensuring reliable operation. Power
dissipation of the device depends on input voltage
and load conditions and can be calculated by:
P D = I OUT xR DSON
due to their capability to withstand input current
surges from low impedance sources, such as
batteries in portable applications. This input
2
(1)
capacitor must be located as close as possible to
the device to assure input stability and less noise.
For PCB layout, a wide copper trace is required for
both IN and GND.
Output Capacitor
A 0.1 μ F capacitor is recommended to connect
However, the maximum power dissipation that can
be handled by the device depends on the
maximum junction to ambient thermal resistance,
maximum ambient temperature, and maximum
device junction temperature, which can be
approximated by the equation below:
between OUT and GND pins to stabilize and
accommodate load transient condition. The output
capacitor has no specific type or ESR requirement.
The amount of the capacitance may be increased
P D (max@ T A ) =
( + 125 ° C ? T A )
θ JA
(2)
without limit. For PCB layout, the output capacitor
must be placed as close as possible to OUT and
GND pins, and keep the traces as short as
possible.
Enable/Shutdown Operation
The AP2280 is turned on by setting the EN pin high,
and is turned off by pulling it low. To ensure proper
operation, the signal source used to drive the EN
pin must be able to swing above and below the
specified turn-on/off voltage thresholds listed in the
Electrical Characteristics section under V IL and V IH .
Discharge Operation
The AP2280 offers discharge option that helps to
discharge the output when disabled. To use this
feature, the DIS pin is connected to OUT pin
externally. If this feature is not used, the DIS pin
should be left open.
For example at V IN =5V, the typical R DSON = 80m ? .
For I OUT =2A, the maximum power dissipation
calculated using equation (1) is P D =0.32W. Based
on θ JA =160°C / W and equation (2), the calculated
junction temperature rise from ambient is
approximately 51°C. Since the maximum junction
temperature is 125°C, the operating ambient
temperature must be kept below 74°C to safely
operate the device.
On the other hand, at T A =85°C and V IN =5V, the
calculated maximum power dissipation from
equation (2) is P Dmax =0.25W. Hence the safe
operating maximum continuous current is 1.77A.
For other application conditions, the users should
recalculate the device maximum power dissipation
based on the operating conditions.
AP2280 Rev. 6
8 of 12
FEBRUARY 2009
? Diodes Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| 0210490851 | CABLE JUMPER 1.25MM .254M 15POS |
| SDR-O | SCOTCH CODE REFILL O |
| RMM08DSEH | CONN EDGECARD 16POS .156 EYELET |
| RCM11DSEH | CONN EDGECARD 22POS .156 EYELET |
| DK-V6-BCCN-G-J | VIRTEX-6 FPGA CONNECTIVITY KIT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AP22804AM8-13 | 功能描述:LOAD SWITCH MSOP-8 制造商:diodes incorporated 系列:* 包装:带卷（TR） 零件状态:在售 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商器件封装:8-MSOP 标准包装:2,500 |
| AP22804ASN-7 | 功能描述:LOAD SWITCH U-DFN2020-6 制造商:diodes incorporated 系列:* 包装:带卷（TR） 零件状态:在售 封装/外壳:6-UFDFN 裸露焊盘 供应商器件封装:U-DFN2020-6 标准包装:3,000 |
| AP22804AW5-7 | 功能描述:IC LOAD SWITCH SOT25 制造商:diodes incorporated 系列:- 包装:剪切带（CT） 零件状态:在售 开关类型:USB 开关 输出数:1 比率 - 输入:输出:1:1 输出配置:高端 输出类型:P 通道 接口:开/关 电压 - 负载:2.7 V ~ 5.5 V 电压 - 电源（Vcc/Vdd）:不需要 电流 - 输出（最大值）:2.5A 导通电阻（典型值）:50 毫欧 输入类型:非反相 特性:负载释放，状态标志 故障保护:限流（固定），超温，UVLO 工作温度:-40°C ~ 85°C（TA） 封装/外壳:SC-74A，SOT-753 供应商器件封装:SOT-25 标准包装:1 |
| AP22804BM8-13 | 功能描述:IC LOAD SWITCH MSOP-8 制造商:diodes incorporated 系列:- 包装:剪切带（CT） 零件状态:在售 开关类型:USB 开关 输出数:1 比率 - 输入:输出:1:1 输出配置:高端 输出类型:P 通道 接口:开/关 电压 - 负载:2.7 V ~ 5.5 V 电压 - 电源（Vcc/Vdd）:不需要 电流 - 输出（最大值）:2.5A 导通电阻（典型值）:50 毫欧 输入类型:非反相 特性:负载释放，状态标志 故障保护:限流（固定），超温，UVLO 工作温度:-40°C ~ 85°C（TA） 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商器件封装:8-MSOP 标准包装:1 |
| AP22804BSN-7 | 功能描述:LOAD SWITCH U-DFN2020-6 制造商:diodes incorporated 系列:* 包装:带卷（TR） 零件状态:在售 封装/外壳:6-UDFN 裸露焊盘 供应商器件封装:U-DFN2020-6 标准包装:3,000 |
发布紧急采购，3分钟左右您将得到回复。