- 您现在的位置：买卖IC网 > Datasheet目录394 > APGAC031 (Microchip Technology)KIT ACC TIRE PRESSURE MON SYSTEM Datasheet资料下载
参数资料
| 型号： | APGAC031 |
| 厂商： | Microchip Technology |
| 文件页数： | 4/12页 |
| 文件大小： | 0K |
| 描述： | KIT ACC TIRE PRESSURE MON SYSTEM |
| 标准包装： | 1 |
| 类型： | 汽车 - 轮胎压力监视器 |
| 频率： | 315MHz |
| 适用于相关产品： | APGRD003 |
| 已供物品： | 轮胎传感器节点 |
AN238
Sensonor SP-13 Sensor IC
FIGURE 3:
SENSONOR SP-13 SENSOR
The SP-13 sensor IC performs several functions. It
measures pressure, temperature, and generates a flag
when the battery voltage drops below a predetermined
threshold. The SP-13 has five unique modes:
IC
Pressure/Temperature Sensor IC
+3V
U4
1.
Storage mode : If the pressure is below 1.5 bar,
pressure is measured every 60 seconds but no
data is sent. If the pressure increases above
1.5 bars, the component shifts into the Initial
mode.
R4
1
2
3
4
5
6
7
GND1
GND2
GND3
V SS
R EXT
GND4
V SS
GND5
TXON
TXD
TXBC
V DD
AV DD
V SS
14
13 x
12
11 x
10
9
8
C10
GP0
2.
Initial mode : This mode occurs at power on or
if the pressure increases above 1.5 bar from
5.6 M Ω
SP-13_SO
0.01 μ F
Storage mode. In this mode, pressure is
measured every 0.85 seconds and data is sent
every 0.85 seconds. This sequence is repeated
256 times. After the sequence is repeated 256
times, the device shifts into the Normal mode
only if pressure is above 1.5 bar. If the pressure
is below 1.5 bar, the device will shift into the
Storage mode.
LF Input Circuitry
The LF input is designed to receive and demodulate a
125 kHz signal and transform the received data into a
specific command. The LF input circuit makes use of
3.
4.
Normal mode : Pressure is measured every
3.4 seconds and data is transmitted every
60 seconds. If the measured pressure differs by
more than 200 mbar from the reference taken
every 60 seconds, the device enters a Pressure
Alert mode.
Pressure Alert mode : It is the same measure-
the internal comparator of the rfPIC microcontroller,
thereby reducing cost, module size and quiescent cur-
rent. The LF input circuitry features a LC tank circuit
that is tuned to 125 kHz. The LF sensing input com-
prises L1 and C11. L1 is specially designed by Coilcraft
for this type of application. It provides good sensitivity
in a compact package. A conventional coil could be
ment and transmitting pattern as the Initial
mode.
5. High Temp Alert mode : If the temperature
exceeds 120 ° C, the SP-13 device enters into
the same measurement and transmitting pattern
as the Initial mode.
The SP-13 also includes a 32-bit identification number
that is programmed into the device at the time of
manufacture. This unique ID, when used by the central
receiver, allows differentiation between S/TXs.
Sensonor, as well as several other manufacturers,
continue to offer enhanced pressure sensing devices of
varying functionality. Therefore, it is recommended that
a TPM developer thoroughly research the market prior
to making a final pressure sensor selection.
DS00238C-page 4
used in its place, but overall circuit sensitivity or range
would be reduced. Schottky diode D3 is used to clamp
the voltage developed across the LC tank to safe lev-
els. The output of the LC tank circuit, after passing
through current limiting resistor R5, is fed into the rfPIC
microcontroller comparator ’s negative input. The com-
parator ’s positive input is configured as V REF through
the rfPIC12F675 V REF module. The output of the com-
parator is then fed into an envelope detector consisting
of Schottky diode D2, capacitor C9 and resistor R3. C9
and R3 are selected to provide adequate filtering of the
LF frequency without rounding the edges of the desired
data signal. The output of the envelope detector is then
fed directly into a port pin on the rfPIC microcontroller
and used to process the LF data.
Without a limiting diode, the LF input circuit may be
prone to being overdriven when strong LF fields are
present. This can be seen when the LF commander
device is in close proximity to the S/TX device. The
envelope detection circuit can be abandoned to reduce
cost, but doing so would require additional data
extraction software.
? 2009 Microchip Technology Inc.
相关PDF资料 |
PDF描述 |
|---|---|
| APGRD003 | KIT TPMS REFERENCE DESIGN |
| APR 400 B420L | SENSOR CURRENT 40A 24V MOD |
| APT1608F3C | EMITTER IR 1.6X0.8 940NM CLR SMD |
| APT1608SF4C-PRV | LED IR 880NM SF4 1.6X0.8MM SMD |
| APT2012F3C | EMITTER IR 2X1.2MM 940NM CLR SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| APGB112-4380-17 | 制造商:Airpax 功能描述:CIRCUIT PROTECTOR HYD MAGNETIC 制造商:Sensata Technologies 功能描述:APGB112-4380-17 /Pole # 3 /Prod Family: 0207 |
| APGB121-4380-15 | 制造商:Airpax 功能描述:CIRCUIT PROTECTOR HYD MAGNETIC 制造商:Sensata Technologies 功能描述:APGB121-4380-15 /Pole # 3 /Prod Family: 0207 |
| APG-BTW400 | 功能描述:射频模块 Bluetooth Access Point Gateway RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
| APGDT001 | 功能描述:界面开发工具 LIN Serial Analyzer RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| APGDT002 | 功能描述:界面开发工具 CAN Bus Analyzer RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。