参数资料
| 型号： | ARS15A12 |
| 厂商： | Panasonic Electric Works |
| 文件页数： | 9/11页 |
| 文件大小： | 0K |
| 描述： | RELAY RF SPDT 500MA 12V |
| 其它有关文件： | Standards Chart |
| 产品目录绘图： | ARS Series ARS15 Series Circuit |
| 标准包装： | 40 |
| 系列： | ARS |
| 继电器类型： | RF |
| 线圈类型： | 锁存，单线圈 |
| 线圈电流： | 16.7mA |
| 线圈电压： | 12VDC |
| 触点形式： | SPDT（1 C 型） |
| 触点额定值（电流）： | 500mA |
| 切换电压： | 30VDC - 最小值 |
| 关闭电压（最大）： | 9 VDC |
| 安装类型： | 表面贴装 |
| 端接类型： | 鸥翼型 |
| 包装： | 管件 |
| 触点材料： | 镀金 |
| 操作时间： | 10ms |
| 释放时间： | 6ms |
| 线圈功率： | 200 mW |
| 线圈电阻： | 720 欧姆 |
| 工作温度： | -40°C ~ 70°C |
| 产品目录页面： | 2598 (CN2011-ZH PDF) |
| 其它名称： | 255-2709 |
RS (ARS)
NOTES
1. Coil operating power
Pure DC current should be applied to the
coil. The wave form should be
rectangular. If it includes ripple, the ripple
factor should be less than 5%.
However, check it with the actual circuit
since the characteristics may be slightly
Single side stable silent type
Humidity, %R.H.
85
Tolerance range
(Avoid freezing (Avoid
when used at condensation
*Relays are in?uenced by the type of PC
board used. Please con?rm with the
actual PC board you plan to use.
*Please avoid re?ow soldering.
2) Surface-mount terminal
In case of automatic soldering, the
following conditions should be observed
different. The nominal operating voltage
should be applied to the coil for more
than 30 ms to set/reset the latching type
relay.
2. Coil connection
temperatures
lower than
0 ° C 32 ° F )
-40
-40
5
when used at
temperatures
higher than
0 ° C 32 ° F )
0 60
32 140
Temperature, ° C ° F
(1) Position of measuring temperature
A
T 2 =230 ° C and higher
1.5 +0.1 dia.
2.0 1.75 8.3 .339
16.0 .079 .069 .327
RS relay 12.0 .630 4.0
.472
.016
When connecting coils, refer to the wiring
diagram to prevent mis-operation or
malfunction.
3. External magnetic ?eld
Since RS relays are highly sensitive
polarized relays, their characteristics will
be affected by a strong external magnetic
?eld. Avoid using the relay under that
condition.
4. Cleaning
For automatic cleaning, the boiling
method is recommended. Avoid
ultrasonic cleaning which subjects the
relays to high frequency vibrations, which
may cause the contacts to stick.
It is recommended that alcoholic solvents
be used.
5. Conditions for operation, transport
and storage conditions
1) Temperature
? Single side stable standard and latching
type: –40 to 70 ° C –40 to 158 ° F
? Single side stable silent type:
–40 to 60 ° C –40 to 140 ° F
2) Humidity: 5 to 85% RH
(Avoid freezing and condensation.)
The humidity range varies with the
temperature. Use within the range
indicated in the graph below.
3) Atmospheric pressure: 86 to 106 kPa
Temperature and humidity range for
usage, transport, and storage:
Single side stable standard
and latching type
Humidity, %R.H.
4) Condensation
Condensation forms when there is a
sudden change in temperature under
high temperature and high humidity
conditions. Condensation will cause
deterioration of the relay insulation.
5) Freezing
Condensation or other moisture may
freeze on the relay when the temperature
is lower than 0 ° C 32 ° F . This causes
problems such as sticking of movable
parts or operational time lags.
6) Low temperature, low humidity
environments
The plastic becomes brittle if the relay is
exposed to a low temperature, low
humidity environment for long periods of
time.
7) Storage requirements
Since the relay is sensitive to humidity,
the surface-mount type is packaged with
tightly sealed anti-humidity packaging.
However, when storing, please be careful
of the following.
(1) Please use promptly once the anti-
humidity pack is opened.
If relays are left as is after unpacking,
they will absorb moisture which will result
in loss of air tightness as a result of case
expansion due to thermal stress when
re?ow soldering during the mounting
process. (within one day, 30 ° C and
60%R.H or less)
(2) When storing for a log period after
opening the anti-humidity pack, storage
A: Surface of PC board where relay is mounted.
(2) IR (infrared re?ow) soldering method
T 3
T 1 =150 to 180 ° C
T 2
T 1 T 3 =250 ° C max.
t 1 =60s to 120s
t 2 =within 30s
t 1 t 2
? Mounting cautions
Rise in relay temperature depends
greatly on the component mix on a given
PC board and the heating method of the
re?ow equipment. Therefore, please test
beforehand using actual equipment to
ensure that the temperature where the
relay terminals are soldered and the
temperature at the top of the relay case
are within the conditions given above.
3) Please meet the following conditions if
this relay is to be soldered by hand.
(1) 260 ° C 500 ° F for max. 10 seconds
(2) 350 ° C 662 ° F for max. 3 seconds
The effect on the relay depends on the
actual substrate used. Please verify the
substrate to be used.
(3) Avoid ultrasonic cleaning. Doing so
will adversely affect relay characteristics.
Please use alcohol-based cleaning
solvents when cleaning relays.
7. Tape and reel packing
1) Tape dimensions
8.6
0
.059 +.004 dia.
0.4
.157
85
Tolerance range
in anti-humidity packaging with an anti-
humidity bag to which silica gel has been
added, is recommended.
X type
Relay polarity bar
11.5
.453
15.00
.591
24.0 ± 0.3
.945 ± .012
(Avoid freezing
when used at
temperatures
(Avoid
condensation
when used at
*Furthermore, if the relay is solder
mounted when it has been subjected to
Z type
Tape coming out direction
(General tolerance: ± 0.1 ± .004 )
21 dia.
.827 dia.
14.961 dia.
80 ± 1 dia.
3.150 dia.
lower than
0 ° C 32 ° F )
-40
-40
5
temperatures
higher than
0 ° C 32 ° F )
0 70
32 158
Temperature, ° C ° F
excessive humidity, cracks and leaks can
occur. Be sure to mount the relay under
the required mounting conditions.
6. Soldering
1) Please meet the following conditions if
this relay is to be automatically soldered.
(1) Preheating: Max. 120 ° C 248 ° F
(terminal solder surface) for max. 120
2) Dimensions of plastic reel
± 0.8
± .031
2.0 ± 0.5
.079 ± .020
380 ± 2 dia.
± .079
± .039
seconds
13 dia.
(2) Soldering: Max. 260 ± 5 ° C 500±9°F for
max. 6 seconds
± 0.2
.512 ± .008 dia. 24.4 +2.0
.961 +.079
2.0 ± 0.2
.079 ± .008
ASCTB106E 201202-T
Panasonic Corporation
Automation Controls Business Unit
industrial.panasonic.com/ac/e/
相关PDF资料 |
PDF描述 |
|---|---|
| 3501-0000 | CONN SOCKET 26POS .050" GOLD |
| G6ZU-1PE DC9 | RELAY RF SPDT 10MA 9V |
| 4-1546700-1 | CONN BARRIER BLOCK 23CIRC 9.53MM |
| 2-1546701-8 | CONN BARRIER BLOCK 23CIRC 9.53MM |
| G6ZU-1PE DC5 | RELAY RF SPDT 10MA 5V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ARS15A24 | 功能描述:高频/射频继电器 RELAY LATCH SPDT 3GHZ 24VDC SMD RoHS:否 制造商:Omron Electronics 触点形式:2 Form C (DPDT-BM) 触点电流额定值: 线圈电压:5 VDC 线圈类型:Non-Latching 频率: 功耗:100 mW 端接类型:Solder Terminal 绝缘:20 dB to 30 dB at 1 GHz 介入损耗:0.2 dB at 1 GHz |
| ARS15A4H | 功能描述:高频/射频继电器 ARS (RS) High Frequency Relay RoHS:否 制造商:Omron Electronics 触点形式:2 Form C (DPDT-BM) 触点电流额定值: 线圈电压:5 VDC 线圈类型:Non-Latching 频率: 功耗:100 mW 端接类型:Solder Terminal 绝缘:20 dB to 30 dB at 1 GHz 介入损耗:0.2 dB at 1 GHz |
| ARS15Y03 | 功能描述:高频/射频继电器 Relay Y layout, 1-coil latching RoHS:否 制造商:Omron Electronics 触点形式:2 Form C (DPDT-BM) 触点电流额定值: 线圈电压:5 VDC 线圈类型:Non-Latching 频率: 功耗:100 mW 端接类型:Solder Terminal 绝缘:20 dB to 30 dB at 1 GHz 介入损耗:0.2 dB at 1 GHz |
| ARS15Y12 | 功能描述:高频/射频继电器 RELAY LATCH SPDT 3GHZ 12VDC SMD RoHS:否 制造商:Omron Electronics 触点形式:2 Form C (DPDT-BM) 触点电流额定值: 线圈电压:5 VDC 线圈类型:Non-Latching 频率: 功耗:100 mW 端接类型:Solder Terminal 绝缘:20 dB to 30 dB at 1 GHz 介入损耗:0.2 dB at 1 GHz |
| ARS15Y24 | 功能描述:高频/射频继电器 RELAY LATCH SPDT 3GHZ 24VDC SMD RoHS:否 制造商:Omron Electronics 触点形式:2 Form C (DPDT-BM) 触点电流额定值: 线圈电压:5 VDC 线圈类型:Non-Latching 频率: 功耗:100 mW 端接类型:Solder Terminal 绝缘:20 dB to 30 dB at 1 GHz 介入损耗:0.2 dB at 1 GHz |
发布紧急采购，3分钟左右您将得到回复。