- 您现在的位置：买卖IC网 > PDF目录20834 > AS1110-BQFT (ams)IC DRIVER LED 16-CHAN 28-WQFN PDF资料下载
参数资料
| 型号： | AS1110-BQFT |
| 厂商： | ams |
| 文件页数： | 12/25页 |
| 文件大小： | 0K |
| 描述： | IC DRIVER LED 16-CHAN 28-WQFN |
| 标准包装： | 5,000 |
| 恒定电流： | 是 |
| 拓扑： | 16 位移位寄存器，PWM |
| 输出数： | 16 |
| 内部驱动器： | 是 |
| 类型 - 主要： | LED 照明显示器，标牌，汽车 |
| 频率： | 50MHz |
| 电源电压： | 3 V ~ 5.5 V |
| 输出电压： | 15V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-QFN（5x5） |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 85°C |
AS1110
Datasheet - D e t a i l e d D e s c r i p t i o n
Figure 13. Switching Global Error Mode Timing Diagram
OEN
t TESTING
t GSW(ERROR)
LD
t SU(ERROR)
t GSW(ERROR)
CLK
t P(I/O)
t GSW(ERROR)
t P(I/O)
t P(I/O)
SDI
T FLAG(IN)
O FLAG(IN)
S FLAG(IN)
SDO
Don’t
Care
T FLAG
Don’t
Care
O FLAG
Don’t
Care
S FLAG
Acquisition of Error
t P4
t SW(ERROR)
t SW(ERROR)
Status
8.3 Error-Detection Mode
Acquisition of the error status occurs at the rising edge of OEN. Error-detection mode is started on the rising edge of LD when OEN is high. The
CLK signal must be low when entering error detection mode. Error detection for open- and shorted-LEDs can only be performed for LEDs that
are switched on during test time. To switch between error-detection modes clock pulses are needed (see Table 5) .
Note: To test all LEDs, a test pattern that turns on all LEDs must be input to the AS1110.
8.4 Global Error Mode
Global error mode is entered when error-detection mode is started. Clock pulses during this period are used to select between temperature,
open-LED, and shorted-LED tests, as well as low-current diagnostic mode and shutdown mode (see Table 5) . In global error mode, an error flag
(T FLAG, O FLAG, S FLAG ) is delivered to pin SDO if any errors are encountered.
Table 5. Global Error Mode Selections
Clock
Pulses
0
1
2
3
4
Output Port
Don't Care
Enabled
Enabled
Don't Care
Don't Care
Error-Detection Mode
Over-Temperature Detection
Open-LED Detection
Shorted-LED Detection
Low-Current Diagnostic Mode
Shutdown Mode
Global Error Flag/Shutdown Condition
T FLAG = SDO = 1: No over-temperature warning.
T FLAG = SDO = 0: Over-temperature warning.
O FLAG = SDO = 1: No open-LED error.
O FLAG = SDO = 0: Open-LED error.
S FLAG = SDO = 1: No shorted-LED error.
S FLAG = SDO = 0: Shorted-LED error.
SDI = 1: Wakeup
SDI = 0: Shutdown
Note: For a valid result SDI must be 1 for the first device.
If there are multiple AS1110s in a chain, the error flag will be gated through all devices. To get a valid result at the end of the chain, a logic 1 must
be applied to the SDI input of the first device of the chain. If one device produces an error this error will show up after n *t P(I/O) + t SW(ERROR) at
pin SDO of the last device in the chain. This means it is not possible to identify which device in the chain produced the error. Therefore, if a global
error occurs, the detailed error report can be run to identify which AS1110, or LED produced the error.
Note: When no error has occurred, the detailed error report can be skipped, setting LD and subsequently OEN low.
Revision 1.6
11 - 24
相关PDF资料 |
PDF描述 |
|---|---|
| TA45-A146F180C0-754-AZM10 | CIRCUIT BRKR THERMAL 18A 2POLE |
| P51-750-S-Y-I12-4.5V-000-000 | SENSOR 750PSI 7/16-20-2B .5-4.5V |
| ECC08DRYH | CONN EDGECARD 16POS DIP .100 SLD |
| P51-3000-S-F-M12-4.5V-000-000 | SENSOR 3000PSI 1/4-18NPT .5-4.5V |
| P51-1000-S-J-P-4.5OVP-000-000 | SENSOR 1000PSI 3/8-24 UNF 4.5V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS1110-BSST | 功能描述:IC DRIVER LED 16-CHAN 24-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 特色产品:LM3445 TRIAC Dimmable LED Driver 标准包装:55 系列:PowerWise® 恒定电流:是 恒定电压:- 拓扑:PWM，降压（降压） 输出数:1 内部驱动器:无 类型 - 主要:- 类型 - 次要:高亮度 LED（HBLED） 频率:30kHz ~ 1MHz 电源电压:8 V ~ 12 V 输出电压:- 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOICN 包装:管件 工作温度:-40°C ~ 125°C 产品目录页面:1285 (CN2011-ZH PDF) 其它名称:LM3445M |
| AS1110BSSU | 制造商:AMS 功能描述:IC LED DRIVER CONSTANT CURRENT SSOP24 制造商:AMS 功能描述:IC, LED DRIVER, CONSTANT CURRENT, SSOP24 制造商:AMS 功能描述:IC, LED DRIVER, CONSTANT CURRENT, SSOP24; Topology:Constant Current; No. of Outputs:16; Output Current:100mA; Output Voltage:15V; Driver Case Style:SSOP; Input Voltage Min:3V; Input Voltage Max:5.5V; Dimming Control Type:Analogue ;RoHS Compliant: Yes |
| AS1110-BSSU | 功能描述:LED显示驱动器 RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| AS1110-EB | 制造商:ams 功能描述:AS1110 Evaluation Board |
| AS1110-QF_EK_ST | 功能描述:AS1110 16, Non-Isolated Output LED Driver Evaluation Board 制造商:ams 系列:- 零件状态:有效 电流 - 输出/通道:100mA 输出和类型:16，非隔离 电压 - 输出:15V 特性:过热保护，开路 LED，短路 LED，诊断 电压 - 输入:3 V ~ 5.5 V 所含物品:板 使用的 IC/零件:AS1110 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。