- 您现在的位置：买卖IC网 > Datasheet目录311 > AS1112C-BQFT (ams)IC DRIVER LED 16CHAN 32-TQFN Datasheet资料下载
参数资料
| 型号： | AS1112C-BQFT |
| 厂商： | ams |
| 文件页数： | 9/20页 |
| 文件大小： | 0K |
| 描述： | IC DRIVER LED 16CHAN 32-TQFN |
| 标准包装： | 1,000 |
| 恒定电流： | 是 |
| 拓扑： | PWM |
| 输出数： | 16 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光，通用 |
| 类型 - 次要： | 颜色 |
| 频率： | 30MHz |
| 电源电压： | 3 V ~ 5.5 V |
| 输出电压： | 15V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN（5x5） |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 85°C |
AS1112
Datasheet - D e t a i l e d D e s c r i p t i o n
9 Detailed Description
Serial Interface
The AS1112 features a serial interface (CLK, SDI, SDO, LD, OEN and MODE), which can be connected to microcontrollers or digital signal pro-
cessors in various configurations.
The rising edge of the CLK signal shifts data from pin SDI to the internal register. After all data is clocked in, the serial data is latched into the
internal registers at the rising edge of the LD signal.
Note: All data is clocked in with the MSB first.
Multiple AS1112 devices can be cascaded by connecting the SDO pin of one device with pin SDI of the next device (see Figure 17 on page 15) .
The SDO pin can also be connected to the microcontroller to receive status information from the AS1112. The serial data format is 96-bit or 192-
bit wide, depending on mode of the device (see LD on page 2) .
Figure 9. Serial Data Input Timing Diagram
MODE
LD
Dot Correction Mode
Data Input Cycle
t H 3
Greyscale Mode
Data Input Cycle
t SU3
t H3
Dot Correction Mode
Data Input Cycle
SDI
DC n -1
LSB
DC n
MSB
DC n
LSB
GS n
MSB
GS n
LSB
DC n +1
MSB
DC n -1
MSB-1
t H2
t SU2
t SU2
CLK
1
96
1
192
1
2
SDO
DC n-1
MSB
DC n-1
MSB -1
DC n-1
LSB
DC n
MSB
X
X
SID
MSB
X
Error Information Output
The open-drain output pin XERR indicates if the device is in one of the two error conditions: overtemperature flag or open LED detect. During
normal operation, the internal transistor connected to pin XERR is turned off and the voltage on XERR is pulled up to V CC through an external
pullup resistor.
If an overtemperature or open LED condition is detected, the internal transistor is switched on, and XERR is pulled to GND. Because XERR is an
open-drain output, multiple AS1112 devices can be ORed together and pulled up to V CC with a single pullup resistor (see Figure 17 on page 15) .
This reduces the number of signals needed to report a system error.
To differentiate the overtemperature flag from the open LED detect flag from pin XERR, the open LED detect flag can be masked out by setting
OEN = 1 (see Table 8) .
www.austriamicrosystems.com/LED-Driver-ICs/AS1112
Revision 1.13
8 - 19
相关PDF资料 |
PDF描述 |
|---|---|
| AS1113-BSST | IC DRIVER LED 16-CHAN 24-SSOP |
| AS1117-BQFT | IC DRIVER 64LED MOBILE 24-TQFN |
| AS1118-BQFT | IC DRIVER 64LED W/DELAY 24-TQFN |
| AS1121B-BQFT | IC DRIVER 16-CH 32-TQFN |
| AS1122B-BQFT | IC LED DVR 12-CH 24-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS1112-EB | 制造商:ams 功能描述:AS1112 Evaluation Board |
| AS1112-XXX-I-A1-D | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog Filter |
| AS1112-XXX-I-A1-S | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog Filter |
| AS1112-XXX-I-A2-D | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog Filter |
| AS1112-XXX-I-A2-S | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog Filter |
发布紧急采购，3分钟左右您将得到回复。