- 您现在的位置：买卖IC网 > Datasheet目录311 > AS1118-BQFT (ams)IC DRIVER 64LED W/DELAY 24-TQFN Datasheet资料下载
参数资料
| 型号： | AS1118-BQFT |
| 厂商： | ams |
| 文件页数： | 15/21页 |
| 文件大小： | 0K |
| 描述： | IC DRIVER 64LED W/DELAY 24-TQFN |
| 标准包装： | 1 |
| 系列： | * |
AS1118
Datasheet - D e t a i l e d D e s c r i p t i o n
Feature Register (0x0E)
The Feature Register is used for enabling various features including switching the device into external clock mode,
applying an external reset, selecting code-B or HEX decoding, enabling or disabling blinking, enabling or disabling the
SPI-compatible interface, setting the blinking rate, and resetting the blink timing.
Note: At power-up the Feature Register is initialized to 0.
Table 20. Feature Register Summary
D7
blink_
start
D6
sync
D5
blink_
freq_sel
D4
blink_en
D3
NU
D2
decode_sel
D1
reg_res
D0
clk_en
Table 21. Feature Register Bit Descriptions (Address (HEX) = 0xXE)
Addr: 0xXE
Feature Register
Enables and disables various device features.
Bit
Bit Name
Default
Access
Bit Description
External clock active.
D0
clk_en
0 R/W
0 = Internal oscillator is used for system clock.
1 = Pin CLK of the serial interface operates as system clock input.
Resets all control registers except the Feature Register.
0 = Reset Disabled. Normal operation.
D1
reg_res
0 R/W
1 = All control registers are reset to default state (except the Feature
Register) identically after power-up.
Note: The Digit Registers maintain their data.
Selects display decoding for the selected digits ( Table 10 on page 10 ).
D2
decode_sel
0 R/W
0 = Enable Code-B decoding (see Table 11 on page 11 ).
1 = Enable HEX decoding (see Table 12 on page 11 ).
D3
NU
Not used
D4
blink_en
0 R/W
Enables blinking.
0 = Disable blinking. 1 = Enable blinking.
Sets blink with low frequency (with the internal oscillator enabled):
D5
blink_freq_sel
0 R/W
0 = Blink period typically is 1 second (0.5s on, 0.5s off).
1 = Blink period is 2 seconds (1s on, 1s off).
Synchronizes blinking on the rising edge of pin LD. The multiplex and
D6
sync
0 R/W
blink timing counter is cleared on the rising edge of pin LD. By setting
this bit in multiple devices, the blink timing can be synchronized across
all the devices.
Start Blinking with display enabled phase. When bit D4 (blink_en) is set,
D7
blink_start
0 R/W
bit D7 determines how blinking starts.
0 = Blinking starts with the display turned off.
1 = Blinking starts with the display turned on.
No-Op Register (0xX0)
The No-Op Register is used when multiple AS1118 devices are cascaded in order to support displays with more than 8
digits. The cascading must be done in such a way that all SDO pins are connected to SDI of the next AS1118 ( see Fig-
ure 20 on page 16 ). The LD and SCL signals are connected to all devices.
For example, if five devices are cascaded, in order to perform a write operation to the fifth device, the write-command
must be followed by four no-operation commands. When the LD signal goes high, all shift registers are latched. The
first four devices will receive no-operation commands and only the fifth device will receive the intended operation com-
mand, and subsequently update its register.
www.austriamicrosystems.com/LED-Driver-ICs/AS1118
Revision 1.01
14 - 20
相关PDF资料 |
PDF描述 |
|---|---|
| AS1121B-BQFT | IC DRIVER 16-CH 32-TQFN |
| AS1122B-BQFT | IC LED DVR 12-CH 24-TQFN |
| AS1123-BTST | IC LED DVR 16-CH 40MA 24-QSOP |
| AS1390A-ZQFT | IC BOOST CTLR/BUCK CONV 20-QFN |
| AS212-L | SOCKET 12V AUTO SAFETY CAP MNT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS1118-XXX-I-A1-D | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog Filter |
| AS1118-XXX-I-A1-S | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog Filter |
| AS1118-XXX-I-A2-D | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog Filter |
| AS1118-XXX-I-A2-S | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog Filter |
| AS1118-XXX-I-A3-D | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog Filter |
发布紧急采购，3分钟左右您将得到回复。