- 您现在的位置：买卖IC网 > PDF目录20832 > AS1122-BQFT (ams)IC LED DVR 12-CH W/DELAY 24-TQFN PDF资料下载
参数资料
| 型号： | AS1122-BQFT |
| 厂商： | ams |
| 文件页数： | 16/23页 |
| 文件大小： | 0K |
| 描述： | IC LED DVR 12-CH W/DELAY 24-TQFN |
| 标准包装： | 1 |
| 系列： | * |
AS1122
Datasheet - D e t a i l e d D e s c r i p t i o n
Status Information Data (SID)
The AS1122 contains an integrated status information register. After latching the correct identifier with a 16 bit data word the input shift register
data is replaced with status information data.
With the next 16 clock cycles the Open LED information, the Overtemperature-Warning and -Error flag as well as the power-on reset (POR) flag
can be read out at pin SDO. The status information data packet is 16 bits wide. Bits 11:0 contain the open LED detection status of each channel.
Bit 12 is the overtemperature-warning flag, bit 13 is the overtemperature-error flag and bit 14 indicates if the POR was triggered. The complete
status information data packet is shown in Figure 34 .
Figure 34. Status Information Data Packet Format
Note: Bit14 (POR) is set to ‘1’ after start-up and after triggering a power-on reset due to a supply voltage drop. Must be set to ‘0’ manually.
Readback the Status Information Data
To read out the SID the read bit in the command data needs to be set to “1”. After the new command data is lachted into the device the SID is
shifted to the SDO register and will be shifted out with the next running clk cycles on CLKI. After keeping the clk low for the time tlow, the device
is reset again and can be programmed with need information.
Figure 35. Reading of the Status Information Register
Setting Maximum Channel Current
The maximum output current per channel is programmed by a single resistor R IREF , which is placed between pin I REF and GND. The voltage on
pin I REF is set by an internal band gap V IREF (1.27V typ). The maximum channel current is equivalent to the current flowing through R IREF mul-
tiplied by a factor of 31.5. The maximum output current is calculated as:
I MAX =
V IREF
x 31.5
(EQ 3)
R IREF
Where:
V IREF = 1.27V;
R IREF = User-selected external resistor.
www.austriamicrosystems.com/LED-Driver-ICs
Revision 1.00
15 - 22
相关PDF资料 |
PDF描述 |
|---|---|
| MAX16804ATP+ | IC LED DRIVR HIGH BRIGHT 20-TQFN |
| REC7.5-4812SRW/H2/A/M/SMD/CTRL | CONV DC/DC 7.5W 36-72VIN 12VOUT |
| P51-50-S-AA-I12-4.5V-000-000 | SENSOR 50PSI 7/16-20 UNF .5-4.5V |
| P51-100-S-M-P-4.5OVP-000-000 | SENSOR 100PSI M10-1.0 6G .5-4.5V |
| P51-75-S-H-M12-4.5V-000-000 | SENSOR 75PSI M12-1.5 6G .5-4.5V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS1122-XXX-I-A1-D | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog Filter |
| AS1122-XXX-I-A1-S | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog Filter |
| AS1122-XXX-I-A2-D | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog Filter |
| AS1122-XXX-I-A2-S | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog Filter |
| AS1122-XXX-I-A3-D | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog Filter |
发布紧急采购，3分钟左右您将得到回复。