- 您现在的位置：买卖IC网 > PDF目录17352 > AS1322 EB (ams)BOARD EVAL AS1322 PDF资料下载
参数资料
| 型号： | AS1322 EB |
| 厂商： | ams |
| 文件页数： | 11/18页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL AS1322 |
| 设计资源： | Design Support Tool |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步升 |
| 输出及类型： | 1，非隔离 |
| 输出电压： | 2.5 ~ 5 V |
| 电流 - 输出： | 150mA 或 500mA |
| 输入电压： | 1 ~ 5 V |
| 稳压器拓扑结构： | 升压 |
| 频率 - 开关： | 1.2MHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | AS1322 |
AS1322
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
9.1 Output Voltage Ripple
The AS1322 is designed to work at high efficiency. In order to reduce the output ripple the following improvements are recommended:
Use a higher output capacitor, up to 44μF and a higher input capacitor (22μF).
Use smaller values for the resistor divider. R1 should be about 300k ? . To avoid a high leakage current from pin VOUT through the resistor
divider to GND, R1 should not be less than 100k ? .
To reduce the output ripple it’s also possible to speed up the feedback loop. To achieve this, place a 22pF (C4 in Figure 20 ) capacitor in
parallel to R1. Via C4 the fast transients are shorted to the FB pin and the feedback loop is even faster. A 1M ? resistor for R1 slows down
the FB loop.
Due to noise and to their non linear behavior, the use of potentiometers is not recommended.
Figure 20. AS1322 - Typical Application for lower Output Voltage Ripple
L1
4.7μH
1
SW
2xAA Battery
6
5
V OUT = 2.8V
C 1
22μF
VIN
AS1322
VOUT
C 4
22pF
R 1
250k ?
C 2
22μF
C 3
22μF
On
4
3
Off
SHDNN
2
GND
FB
R 2
196k ?
Note: For correct measurements of the output ripple connect the oscilloscope probe as close as possible to the positive plate of the C OUT
and connect the GND of the oscilloscope probe to the negative plate of the C OUT . This will reduce the inductive coupling and will
deliver a more accurate measurement result.
The output ripple is getting higher as V IN is getting closer to V OUT . Figure 21 shows that the above mentioned improvements reduce the output
voltage ripple. If V IN is higher than V OUT the AS1322 stops switching and V IN is connected to V OUT via the inductor and the internal P-FET.
Figure 21. Output Voltage Ripple vs. Input Voltage; V OUT = 2.8V, I OUT = 0.8mA
125
Cout = 44μF
Cout = 66μF
100
75
50
25
0
Cout = 44μF + C4 = 22pF
0.5
1
1.5
2
2.5
3
3.5
Input Voltage (V)
www.ams.com/DC-DC_Step-Up/AS1322
Revision 1.10
11 - 18
相关PDF资料 |
PDF描述 |
|---|---|
| A9CAA-0404F | FLEX CABLE - AFG04A/AF04/AFE04T |
| ISL60002DIH330Z-TK | IC VREF SERIES PREC 3V SOT-23-3 |
| LQW2UASR75J00L | IND 750NH 360MA SRF 360MHZ 1008 |
| AS1326 EB | BOARD EVAL AS1326 |
| EGM06DRMH | CONN EDGECARD 12POS .156 WW |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS1-322-W3-302 | 制造商:TE Connectivity 功能描述: |
| AS1323 | 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:1.6uA Quiescent Current, Single Cell, DC-DC Step-up Converter |
| AS1323_04 | 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:1.6??A Quiescent Current, Single Cell, DC-DC Step-up Converter |
| AS1323_1 | 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:1.6uA Quiescent Current, Single Cell, DC-DC Step-up Converter |
| AS1323-27 | 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:1.6レA Quiescent Current, Single Cell, DC-DC Step-Up Converter |
发布紧急采购，3分钟左右您将得到回复。