参数资料
| 型号： | AS1322A-BTTT |
| 厂商： | ams |
| 文件页数： | 2/18页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST SYNC ADJ TSOT23-6 |
| 设计资源： | Design Support Tool |
| 标准包装： | 1 |
| 类型： | 升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 2.5 V ~ 5 V |
| 输入电压： | 0.65 V ~ 5 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 1.2MHz |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 细型，TSOT-23-6 |
| 包装： | 标准包装 |
| 供应商设备封装： | TSOT-23-6 |
| 其它名称： | AS1322A-BTTTDKR |
AS1322
Datasheet - P i n A s s i g n m e n t s
4 Pin Assignments
Figure 2. Pin Assignments (Top View)
SW 1
6 VIN
GND 2
AS1322
5
VOUT
4.1 Pin Descriptions
Table 2. Pin Descriptions
FB 3
4 SHDNN
Pin Number
1
2
3
4
5
6
Pin Name
SW
GND
FB
SHDNN
VOUT
VIN
Description
Switch Pin . Connect an inductor between this pin and V IN . Keep the PCB trace lengths as
short and wide as is practical to reduce EMI and voltage overshoot. If the inductor current
falls to zero, or pin SHDNN is low, an internal 100 ? anti-ringing switch is connected from this
pin to V IN to minimize EMI.
Note: An optional Schottky diode can be connected between this pin and V OUT .
Signal and Power Ground . Provide a short, direct PCB path between this pin and the
negative side of the output capacitor(s).
Feedback Pin . Feedback input to the g m error amplifier. Connect a resistor divider tap to this
pin. The output voltage can be adjusted from 2.5 to 5V by: V OUT = 1.23V[1 + (R 1 /R 2 )]
Shutdown Pin . Logic controlled shutdown input.
1 = Normal operation, 1.2MHz typical operating frequency.
0 = Shutdown; quiescent current <1μA. If SHDNN is undefined, pin SW may ring.
Note: In a typical application, SHDNN should be connected to V IN through a 1M ? pull-up
resistor.
Output Voltage Sense Input and Drain of the Internal PMOS Synchronous Rectifier .
Bias is derived from V OUT when V OUT exceeds V IN . PCB trace length from V OUT to the
output filter capacitor(s) should be as short and wide as is practical. V OUT is held at
approximately V IN - 0.6V during shutdown.
Input Voltage . The AS1322 gets its start-up bias from V IN unless V OUT exceeds V IN , in
which case the bias is derived from V OUT . Thus, once started, operation is completely
independent from V IN . Operation is only limited by the output power level and the internal
series resistance of the supply.
www.ams.com/DC-DC_Step-Up/AS1322
Revision 1.10
2 - 18
相关PDF资料 |
PDF描述 |
|---|---|
| AS1323-BTTT-30 | IC REG BST SYNC 3V 0.1A TSOT23-5 |
| AS1324-BTTT-18 | IC REG BUCK SYNC 1.8V TSOT23-5 |
| AS1326A-BTDT-1K | IC REG BST SYNC 3.3V/ADJ 10-TDFN |
| AS1326B-BTDT | IC REG BST SYNC 3.3V/ADJ 10TDFN |
| AS1329B-BTTT | IC REG BOOST SYNC ADJ TSOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS1322A-TT_EK_ST | 功能描述:AS1322 - DC/DC, Step Up 1, Non-Isolated Outputs Evaluation Board 制造商:ams 系列:- 零件状态:有效 主要用途:DC/DC，步升 输出和类型:1，非隔离 功率 - 输出:- 电压 - 输出:2.5 V ~ 5 V 电流 - 输出:570mA 电压 - 输入:1 V ~ 5 V 稳压器拓扑:升压 频率 - 开关:1.2MHz 板类型:完全填充 所含物品:板 使用的 IC/零件:AS1322 标准包装:1 |
| AS1322B | 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:Low Voltage, Micropower, DC-DC Step-Up Converters |
| AS1322BBTTT | 制造商:AMS 功能描述:IC STEP-UP DC/DC CONVERTER 6-SOT-23 |
| AS1322B-BTTT | 功能描述:IC REG BOOST SYNC ADJ TSOT23-6 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| AS1322-EB | 制造商:ams 功能描述:AS1322 Evaluation Board |
发布紧急采购，3分钟左右您将得到回复。