参数资料
| 型号： | AS1329B-BTTT |
| 厂商： | ams |
| 文件页数： | 12/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST SYNC ADJ TSOT23-6 |
| 标准包装： | 1 |
| 类型： | 升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 2.5 V ~ 5 V |
| 输入电压： | 0.65 V ~ 5 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 1.2MHz |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 细型，TSOT-23-6 |
| 包装： | 标准包装 |
| 供应商设备封装： | TSOT-23-6 |
| 其它名称： | AS1329B-BTTTDKR |
AS1329
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
9.1 Output Voltage Ripple
The AS1329 is designed to work at high efficiency. In order to reduce the output ripple the following improvements are recommended:
Use a higher output capacitor, up to 44μF and a higher input capacitor (22μF).
Use smaller values for the resistor divider. R1 should be about 300k ? . To avoid a high leakage current from pin VOUT through the resistor
divider to GND, R1 should not be less than 100k ? ..
To reduce the output ripple it’s also possible to speed up the feedback loop. To achieve this, place a 22pF (C4 in Figure 24 ) capacitor in
parallel to R1. Via C4 the fast transients are shorted to the FB pin and the feedback loop is even faster. A 1M ? resistor for R1 slows down
the FB loop.
Due to noise and to their non linear behavior, the use of potentiometers is not recommended.
Figure 24. AS1329 - Typical Application for lower Output Voltage Ripple
L1
4.7μH
1
SW
2xAA Battery
6
5
V OUT = 2.8V
C 1
22μF
VIN
AS1329
VOUT
C 4
22pF
R 1
250k ?
C 2
22μF
C 3
22μF
On
4
3
Off
SHDNN
2
GND
FB
R 2
196k ?
Note: For correct measurements of the output ripple connect the oscilloscope probe as close as possible to the positive plate of the C OUT
and connect the GND of the oscilloscope probe to the negative plate of the C OUT . This will reduce the inductive coupling and will
deliver a more accurate measurement result.
The output ripple is getting higher as V IN is getting closer to V OUT . Figure 25 shows that the above mentioned improvements reduce the output
voltage ripple. If V IN is higher than V OUT the AS1329 stops switching and V IN is connected to V OUT via the inductor and the internal P-FET.
Figure 25. Output Voltage Ripple vs. Input Voltage; V OUT = 2.8V, I OUT = 0.8mA
125
Cout = 44μF
Cout = 66μF
100
75
50
25
0
Cout = 44μF + C4 = 22pF
0.5
1
1.5
2
2.5
3
3.5
Input Voltage (V)
www.ams.com/DC-DC_Step-Up/AS1329
Revision 1.12
12 - 20
相关PDF资料 |
PDF描述 |
|---|---|
| AS1330-BTDT-30 | IC REG BOOST SYNC 3V 0.15A 8TDFN |
| AS1331-BTDT-25-1K | IC REG BUCK BST SYNC 2.5V 10TDFN |
| AS1331-BTDT-33-6K | IC REG BUCK BST SYNC 3.3V 10TDFN |
| AS1332-BWLT | IC CONV BUCK 400MA ADJ 8WLCSP |
| AS1334-BTDT-30 | IC REG BUCK SYNC 3V 0.65A 8TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS1329B-EB | 制造商:ams 功能描述:AS1329B Evaluation Board |
| AS1329B-TT_EK_ST | 功能描述:AS1329B - DC/DC, Step Up 1, Non-Isolated Outputs Evaluation Board 制造商:ams 系列:- 零件状态:有效 主要用途:DC/DC，步升 输出和类型:1，非隔离 功率 - 输出:- 电压 - 输出:3.3V 或 5V 电流 - 输出:570mA 电压 - 输入:0.85 V ~ 5 V 稳压器拓扑:升压 频率 - 开关:1.2MHz 板类型:完全填充 所含物品:板 使用的 IC/零件:AS1329B 标准包装:1 |
| AS1329C | 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:Low Voltage, Micropower, DC-DC Step-Up Converters |
| AS1329C EB | 功能描述:BOARD EVAL AS1329C RoHS:否 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| AS1329CBTTT | 制造商:AMS 功能描述:IC STEP-UP DC/DC CONVERTER 6-SOT-23 |
发布紧急采购，3分钟左右您将得到回复。