参数资料
| 型号： | AS1369-BWLT-28-10K |
| 厂商： | ams |
| 文件页数： | 14/22页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 2.8V .2A 4WLCSP |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 2.8V |
| 输入电压： | 最高 5.5V |
| 电压 - 压降（标准）： | 0.08V @ 200mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 200mA |
| 电流 - 限制（最小）： | 210mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 4-UFBGA，WLCSP |
| 供应商设备封装： | 4-WLCSP |
| 包装： | 标准包装 |
| 其它名称： | AS1369-BWLT-28-10KDKR AS1369-BWLT-28DKR AS1369-BWLT-28DKR-ND |
AS1369
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
8 Application Information
Figure 46. Typical Application Diagram
V IN
V OUT
C1
EN
V REF
On/Off
Control
_
+
Thermal &
Over Current
Protection
GND
C2
Figure 46 shows the block diagram of the AS1369. It identifies the basics of a series linear regulator employing a P-Channel MOSFET as the
control element. A stable voltage reference (REF in Figure 46 ) is compared with an attenuated sample of the output voltage. Any difference
between the two voltages (reference and sample) creates an output from the error amplifier that drives the series control element to reduce the
difference to a minimum. The error amplifier incorporates additional buffering to drive the relatively large gate capacitance of the series pass P-
channel MOSFET, when additional drive current is required under transient conditions. Input supply variations are absorbed by the series
element, and output voltage variations with loading are absorbed by the low output impedance of the regulator.
8.1 Dropout Voltage
Dropout is the input to output voltage difference, below which the linear regulator ceases to regulate. At this point, the output voltage change
follows the input voltage change. Dropout voltage may be measured at different load currents, but is usually specified at maximum output. As a
result, the MOSFET maximum series resistance over temperature is obtained. More generally:
V DROPOUT = I LOAD x R SERIES
Dropout is probably the most important specification when the regulator is used in a battery application. The dropout performance of the
regulator defines the useful “end of life” of the battery before replacement or re-charge is required.
(EQ 2)
www.austriamicrosystems.com/LDOs/AS1369
Revision 1.7
13 - 21
相关PDF资料 |
PDF描述 |
|---|---|
| X40435S14-AT1 | IC VOLT MON TRPL EEPROM 14-SOIC |
| MAX8717ETI+ | IC CNTRLR PWR SUP 28-TQFN |
| AYM18DRMH-S288 | CONN EDGECARD 36POS .156 EXTEND |
| X4043S8IT2 | IC SUPERVISOR CPU 4K EE 8-SOIC |
| ASM18DRMH-S288 | CONN EDGECARD 36POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS1369-BWLT-28-1K | 功能描述:IC REG LDO 2.8V .2A 4WLCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.5V 输入电压:2.5 V ~ 5.5 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:300mA（最小值） 电流 - 限制（最小）:360mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 供应商设备封装:TSOT-23-5 包装:带卷 (TR) |
| AS1369-BWLT-30 | 功能描述:IC REG LDO 3V .2A 4WLCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.5V 输入电压:2.5 V ~ 5.5 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:300mA（最小值） 电流 - 限制（最小）:360mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 供应商设备封装:TSOT-23-5 包装:带卷 (TR) |
| AS1369-BWLT-30-10K | 制造商:ams 功能描述:IC REG LDO 3V 0.2A 4WLCSP 制造商:ams 功能描述:T&R / WLP |
| AS1369-BWLT-33 | 功能描述:低压差控制器 - LDO RoHS:否 制造商:Micrel 最大输入电压:5.5 V 输出电压:Adjustable 输出电流:10 mA 负载调节: 输出类型:Adjustable, Fixed 输出端数量:1 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-6 |
| AS1369-BWLT-33-10K | 制造商:AMS 功能描述:IC REG LDO 3.3V 0.2A 4WLCSP |
发布紧急采购，3分钟左右您将得到回复。